Voron 2.4 kit from

Подписаться 3,2 тыс.

Просмотров 2,3 тыс.

50% 1

Open box video of #voron #3Dprinter kit from Formbot. I highly suggest you order a kit (anywhere actually) than sourcing parts yourself unless you build a custom #Voron which in the end is just a regular custom 3D printer that is not supported by the Voron community. To order a kit from Formbot you can use this link www.formbot3d....
By the way, here is the list of upgrades that I ordered to upgrade #Formbot kit to the next level. You can definitely do to your #voron 2.4 3D printer as well.
Formbot 3D Printer kit:
www.formbot3d....
Affiliate Link:
Pin mod:
* D5 M3 Steel Pins: s.click.aliexp...
CAN Bus:
* PG7 Cable Gland: s.click.aliexp...
* CAN Board: s.click.aliexp...
PCB Klicky Proble:
* s.click.aliexp...
Dragon Hotend:
* Dragon Core: s.click.aliexp...
* Dragon Heat sink: s.click.aliexp...
* Dragon Heat Block s.click.aliexp...
* Dragon Heater Cartridge s.click.aliexp...
* Dragon Thermistor s.click.aliexp...
GT2 Bearing Idlers
Dial Test indicator: s.click.aliexp...
By the way, I use dial test indicator to check for a lot of things needed for 3D printer hobby. Buy one if you don't already have it. I'd suggest for Chinese made one below (affiliate link which also helps the channel) which doesn't cost a lot like Mitutoyo ones. Remember don't put magnet close to these Chinese made dial test indicators. You might damage them.
▬ Get Connected ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
► RU-vid: / lavithhcm
► Twitter: / lavitht
► Facebook: / lavitht
► Instagram: / di.ai.why
► Personal Website: www.thinhla.com
► Github: github.com/cucac

Опубликовано:

10 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 8

@erik3205 9 месяцев назад

I purchased a Trident from them last year, I was pretty pleased with what I got.

@lavithhcm 9 месяцев назад

so far so good except one linear rail has some play and sound rough. They try to send me a sliding block as replacement and hope it fixes the issue. This is my first Voron and I did really enjoy the building process and 2 weeks of printing out my own parts. 🙂 I did check the stepper motors and was pleased as well of motor quality ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WWF8mjZLdJ8.htmlsi=HLLxC0tTW_jUezMS

@michelcote 8 месяцев назад

probably hard 400 serie stainless steel which is magnetic. It's required for hardness of the bearing. It will rust but way less than steel. properly lubricated, rust will be no problems.

@lavithhcm 8 месяцев назад

Thanks for the info about the stainless steel 400 series

@Shalominati 9 месяцев назад

Looking forward to following your build!

@lavithhcm 9 месяцев назад

Thank you! I really enjoy "lego" building process 😍. At this point, finished my frame. 1 Y axis member extrusion a little twisted and waiting for formbot reply.