VW T4 Transporter Door Lock Cylinder Replacement, Key Barrel Repair Fix

Подписаться 5 тыс.

Просмотров 50 тыс.

50% 1

VW T4 Transporter Door Lock Cylinder Replacement, Key Barrel Repair Fix. This repair method can be applied to the side door and both front doors. Volkswagen Transporter / Caravelle / Multivan / Syncro / Doka.
www.buymeacoffee.com/t4tipsgu...
VW T4 Transporter Door Lock Zylinder Ersatz, Schlüssel Fass reparieren.
VW T4 Transporter porte serrure cylindre remplacement, baril clés réparation Fix.
VW T4 Transporter puerta cerradura cilindro recambio, barril clave reparación Fix.
VW T4 Transporter deur Lock cilinder vervanging, belangrijke vat Reparatie Fix.
VW T4 Transporter porta serratura cilindro sostituzione, Nottolino chiave riparazione Fix.
Due to factors beyond the control of T4 Tips & Guides, I can not guarantee against improper use or unauthorized modifications of this information. T4 Tips & Guides assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. T4 Tips & Guides recommends safe practices when working on vehicles and / or with tools seen or implied in this video. Due to factors beyond the control of T4 Tips & Guides, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not T4 Tips & Guides.

Авто/Мото

Опубликовано:

14 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 42

@T4TipsGuides 8 месяцев назад

8 Years later and the lock is still working perfectly.

@T4TipsGuides 6 лет назад

Two years later and the lock is still working perfectly.

@T4TipsGuides 3 года назад

Over 5 years now since the repair and the lock is still working perfectly.

@whatcanisayflur 3 года назад

Awesome content so useful!

@abogadossa 6 лет назад

Gracias. Me has solucionado mi problema

@eddy6237 8 лет назад

I really enjoy your clips, really informative and clear, keep them coming buddy. Top job.

@T4TipsGuides 8 лет назад

Thank you

@JKMediaCorp 3 года назад

I recently bought a 2002 Eurovan MV, and it came with 3 different keys. I was able rekey the liftgate AND the driver's door to match the ignition, passenger door, and sliding door. Additionally the angle at 4:21 allow me to figure out just where and how that "extra" spring on my desk was supposed to go. Since I couldn't see anyplace obvious and the latch still functioned without it. So thanks for this video.

@T4TipsGuides 3 года назад

Glad to hear the video helped. Thanks for watching.

@omar52500 6 лет назад

Thanks a lot 😄

@haraldpost 8 лет назад

Absolutely brilliant vid! Subscribed.

@T4TipsGuides 8 лет назад

+haraldpost Thanks, I try and cover all aspects of the job, more video's to come.

@Mr_wayne0805 8 лет назад

Thanks for the video. I was In bits today as I locked the sliding door, pulled the key out and the barrel was still attached to the key. thought I was going to need a new lock but watching the video, I may only need to fine the small pin you are knocking out at the beginning.

@T4TipsGuides 8 лет назад

Hope you got it sorted, I thought it was going to be expensive but the barrel was only £16 direct from VW.

@Mr_wayne0805 8 лет назад

+T4 Tips & Guides luckily we have a few good guys at work with all the tools n knowledge required to build almost anything from scratch. i took the barrel to bits cleaned everything up and replaced a pin that had snapped in locking mechanism inside the door. works like new. many thanks again.

@aliceartwork 5 лет назад

what did you use to make a new pin? and did you have to take the whole lock off to get the pin back in? @@Mr_wayne0805

@kestutis29 8 лет назад

Thanks, great vid !

@T4TipsGuides 8 лет назад

+Chris G Thanks, hope it helped you fix your lock.

@johno7808 8 лет назад

Really really helpful thank you for sharing 👍

@T4TipsGuides 8 лет назад

+Jono Muzz Thank you, I'm working on a fix for the broken heater control problem at the moment, will get that uploaded when it is ready.

@ollie-allen 5 месяцев назад

Great video. I am looking to convert my T4 from barn doors to a tailgate. I have read that the lock barrels are different. Do you think, by using your process, the wafers could be swapped over from the barn door barrel to a tailgate barrel in order for it to use the same key? Cheers

@T4TipsGuides 5 месяцев назад

Yes. I believe the front doors, side sliding doors, and barn doors use the same barrel. The up and over door or tailgate you wish to fit uses a slightly longer barrel. They contain the same amount of wafers/tumblers.

@cristianrosortega1443 3 года назад

Great Video! Btw , what's the transparent liquid used to clean the cylinder and other metal pieces?

@T4TipsGuides 3 года назад

I used a citrus based de-greaser. It is called Virosol.

@mtunmore3759 4 года назад

at 3.32 mins you can see inside the cylinder housing and there are four strips of metal which act as a key stop (?). Would anyone know what they are called please? Trying to find some replacement. Following this very helpful video I have found there are two missing from my lock, thus it will not let me open the door and take key out!

@lazydog4777 8 лет назад

excellent, bookmarked. just snapped off driver side lock yesterday. either tampered with, or has been broken for a while,and just came out now. so..? i can modify a replacement to work with old key? - do you have a tip for removing the plastic studs retaining lining panels inside the van model? thanks for the tutorial, would be lost without it.

@T4TipsGuides 8 лет назад

+lazy dog I remember when the drivers door lock barrel broke on my T4, half the barrel came out and was on the end of the key! As for the plastic studs, they can be a pain to get out, I have just taken the fibreboard roof panels out to replace with plywood ones. You can get a bag of 50 panels studs on ebay for about a fiver if you need to replace any.

@MisfitsAndMavericks 4 года назад

Thanks for the video, do you have any tips for placing the top 3 pins if you dont know which numbers go where? I lost the top half of the barrel.... Many thanks

@T4TipsGuides 4 года назад

It was a while ago now that I did this job but if I recall correctly there are 6 or 7 types of wafer/pin so to work out which ones go where should only take a couple minutes via trial and error. I know the people who have done this job many time aquire the ability set up a barrel just by looking at the key profile.

@e_valley2707 7 лет назад

Great video. Having problems getting the "pin" out that holds the barrel in place. Any suggestions?

@T4TipsGuides 7 лет назад

All I can suggest is trying to tap the pin out from the opposite side I show in the video, it may hve been removed before and could have been bent or damaged. Are you trying to knock it out with a short length of 2mm diameter rod as suggested?

@e_valley2707 7 лет назад

yes 2mm but the pin has only budged maybe 4mm. I think I'm into the barrel hole but that pin is a a real pia ... mind you the vehicle is 25 years old.

@aliceartwork 5 лет назад

Do you have any tips on what to do if you loose the spring for the barrel?

@T4TipsGuides 5 лет назад

Hi Alice, you can buy the springs on eBay (UK) they are £4.25 a bag, search for "NEW GENUINE VW AUDI SEAT LOCK BARREL TUMBLER PLATE SPRINGS 443837254" Hope that helps.

@peedee2994 5 лет назад

Hi. Just found this video as my drivers door lock has recently gone. I bought a new barrel with new key and my question is.. Do i need to go through the whole removing wafers and springs etc or just put in the new barrell that is already loaded with wafers and springs. If i dont mind having a new key for just the driver door then is it that simple? Thanks

@T4TipsGuides 5 лет назад

I would buy a genuine barrel and fit the wafers from the old barrel and continue to use the original key that matches the other locks. If you have bought a barrel with the wafers fitted, I assume it is an aftermarket one, I guess this will fit into the mechanism. Fitting the genuine wafers into a non genuine barrel may be an option, only one way to find that out, difficult for me to say without seeing what you have bought as a replacement. If you are not bothered about having different keys you should be ok just doing a straight swap, again, it is difficult to say for sure when you can't see the parts.

@t4oomf442 7 лет назад

i was thinking of replaceing handle with non genuine as vw want £250 and non gen is £25 what do you think please ?

@T4TipsGuides 6 лет назад

I would buy a second hand genuine part, the non genuine will not be as good a quality.

@Wendybellrings 8 лет назад

What happened to the rubber seal that stops all the grot getting in and causing the lock to fail ? You didn't replace it.

@T4TipsGuides 8 лет назад

+Robert Warner Hi Robert, if you have a look at 7:04 on the video you can see the new barrel has the seal you mention in place (a new seal was included with the new barrel and was already fitted when I took it out of the packet). If reusing the old barrel the seal can be cleaned and reused.

@stephane5997 Год назад

Hello to you, i see that you're a t4 spécialiste, i have a problem on my t4 1.9td abl, when cold i have a lot of trouble starting i have to use brake cleaner to get it to start... My glow plus are New my battery is 1 year old thé compressions are good and when it agrees to start it Stokes à little Black and thé engine coucghs, can it com from thé solenoid valve or the injection pump i don't know if you can hello me.. once it start it runs fine currently i'm in the moutains and this problem appears when it's vers cold last year there were holes in the cold accélération once it mounted at 90° everything Was rule we can talk to ofter you money in exchange this truck is my whole life this is my house...

@T4TipsGuides Год назад

Hi, sorry to hear you are having problems. Difficult to diagnose without having the van to look at. Possible pump timing issue. Is your cold start handle in place? The cable, more of a thin metal rod, can snap if not kept lubricated. The cold start advances the throttle and assists in starting. Best to visit a VW specialist who can diagnose the issue. Sorry I cannot help more. Hope you get it fixed.