Walk-around - Land Cruiser Prado 120 tourer 

indeed

No worries, glad it was helpful for you :)

Glad to hear, thanks

I just bought a GX 470, it doesn't seem to hard to do most of it.

No worries, thanks mate

Thanks mate, good luck with your build :)

No worries, thanks mate!

Thanks mate - Yeah I ended up moving my compressor to inside the car in the boot so not so much dust gets into it and its cooler in there, I have an outlet at the back now rather than the front

No worries, good luck with the projects.

@@chappelle121 Chappelle can you plz tell me is your cargo barrier a full size one or have you fitted the half cargo barrier size

@@rt-ks2bh it was a full size cargo barrier, it was actually to suit a mitsubishi van I got it for free and just cut it and bolted the bottom to the top of the drawers. That way it left room for the water bladder between it and the seats.

@@chappelle121 Thx for your reply,,,appreciated and very well thought out,,cheers

Awesome! glad it was helpful - thanks for your comment

Thanks mate - yeah probably I'll do an update video of some sort, I have added a lift kit and winch and a bash plate and some other small changes since this video. Just subscribe i suppose and you'll see when I end up making more.

Sounds good... Sub'ed :)

Thanks, Its from 4wd Supa Centre, its the 'Full Length Steel Roof Rack', 220cm long

Thank you, yes I did.

Nope, never had any water come in there. I have since re-wired those and ran the wires just to look more tidy. I now have them come out of the left tail light and up to the roof there.

Hi mate, thanks ! I don't have plans unfortunately, that one was all just off the cuff figuring it as I go. Basically just got a bit of wood for the divider and cut it in a shape that would work combined with the angle off the cargo barrier, couple hinges and carpet and its done! the shelf was the same deal, just got some wood and carpet and cut to fit in the space

Mine are just through the plastic only which is sufficient.

Hi mate, yes - 1 hole is drilled and just a nut on the back of the plastic, and then got 1 longer bolt of the same thread to go into the original threaded car body mounting hole.

no worries! No - i have not had any issues with the DCDC charger, works well.

Hi Mate, the titan draws you can actually buy vehicle specific, mine is a set specifically for the Prado 120 series - then it has everything you need to fit and the wings suit properly.

If its a kings thumper max dual compressor, it should have an inbuilt pressure switch, you don't have to do anything it just cuts out when it reaches a certain pressure, which if your trigger is closed and it's not leaking anywhere it should reach that pressure very quickly and just cut out until you open the trigger or whatever again which will turn it back on.

Hi mate, have since moved the air compressor inside of the car in my drawer setup instead - in saying that I did a few small water crossings and it was not a problem for me - must of kept up enough momentum to keep water flooding the engine bay too much. Only stock breathers which actually run pretty high up already - one of those jobs on the to do list though!

This particular air compressor has a pressure switch built in. You can modify another compressor by adding a pressure switch fairly cheaply if you are bit of a handyman and not scared of a bit of wiring. Should be able to find some info online about adding a pressure switch im sure.

Hey mate, there is a rubber bung just under the carpet near the rear left tail light area (near the jack compartment) . If you look under the car you will see it. Drill a hole through and poke the hose through

Not sure sorry, haven't had it weighed.

Hi mate, thanks - it is home made, everything is from the local hardware shop (bunnings)

Depends where you are, here in Perth Western Australia there are definitely no issues, a very common early mod for most 4x4 owners here. Most 4x4's here have bull bars here. You will need to check with your local authority on local laws and regulations.

Thanks mate, It is the 'Wanderer Aluminium Folding Table' from BCF

Shelf and divider are a homejob DIY, just MDF cut out and wrapped in marine carpet

Hi there, I used black Plasti dip, so it is removable if i want to. (and it has held up really well even with off road use). there are lots of videos online on how to plasti dip rims.

Hey mate, got mine from 'total tools' in Joondalup

Yeah you see that a fair bit, AGM's ideally should not be in the engine bay, however for me I didn't have another good place to put it, but it is working just fine... I run my lights, fridge, charging phones etc... while camping and in the morning the voltage is still like 12.6V so plenty of juice by morning. the DC DC charger I use gives it a nice full charge and its temperature compensated - it has a temperature probe to help it charge efficiently so if its hot it wont pump so much current into it I guess. (its a Projecta Inteli-carge) On the Prado the battery is right behind the headlight too so I don't think it gets that hot, there's probably some decent airflow there.

They are just self tap screws from memory and has been just fine, Cheers.

It was so long ago i don't remember to be honest, wood i would guess around 18mm. Attached to the handles by getting some threaded eye bolts that goes into the same thread as the handles. then another eye bolt on the shelf, and then a turnbuckle that goes between those eye bolts. and back the back just bolted to the cargo barrier.

Ebay - a seller called mycarslook, it was advertised as a Navara expedition decals, and I just messaged them and asked them to change it to the land cruiser logo.

We have two first aid kits in the car with various extra bits chucked in each