White Cement Jar (DIY Candle Jar Using Titanium Dioxide)

Подписаться 10 тыс.

Просмотров 11 тыс.

50% 1

If you are looking to create a white cement jar you can DIY using Titanium Dioxide. These cement jars are good for candles, plants or whatever your creative mind desires.
To purchase my concrete candle jar making course click below.
theupvibe.com/course/
My Etsy Shop for Stylish Downloadable Labels
www.etsy.com/shop/UPVibeCreat...
WEBSITE: theupvibe.com/
INSTAGRAM: / up_vibe
TIKTOK: / up_vibe
Earth Safe Finishes Concrete Sealers
😎Quick Dip Matte 32oz bit.ly/3DChNXg
😎Quick Dip Matte 1 Gal bit.ly/3OqDFKq
😎Quick Dip Gloss 32oz bit.ly/45OdMvD
😎Quick Dip Gloss 1 Gal bit.ly/3NejFLC
Earth Safe Finishes Hydrostone Sealers
😎Hydro Dip 32 oz: bit.ly/3Q2YGvn
😎Hydro Dip 1 Gallon: bit.ly/3tHz7IH
SILICONE MOLDS
😎www.boowannicole.com/UPVIBEEXCL
😎WAX MELTERS
10 Quart Wax Melter - amzn.to/4etXZ9P
5 Quart Wax Melter - amzn.to/4c7EkL3
4 Quart Wax Melter - amzn.to/3xBMHQ5
CUSTOM METALIC or STANDARD CANDLE LABELS:
😎bit.ly/4ahOAiM
AMAZON STOREFRONT: (All supplies I use from Amazon are linked below)
😎www.amazon.com/shop/upvibecandle
Disclosure: As an Amazon Associate, I earn from qualifying purchases. This page may contain affiliate links, and if you make a purchase through these links, I may earn a small commission at no additional cost to you.
UP VIBE CONCRETE CANDLE JAR MAKING SUPPLIES
😎Oval Silicone Mold: amzn.to/36SqIXO
😎Silicone Mold: amzn.to/34RHXqJ
😎Black Pigment: amzn.to/3toGyAF
😎Titanium Dioxide: amzn.to/33MO7si
😎Respirator: amzn.to/3sbGq89
😎Vibrating Machine: amzn.to/37k7x9e
😎Scale: amzn.to/3vkkOHL
😎Rubber Feet: amzn.to/3OU88z3
😎Eco Advance: amzn.to/3HIdexA
😎Pure Tung Oil: amzn.to/3HJUZrl
😎Simple Coat: amzn.to/40fXxow
😎Rutland Sealer: amzn.to/3NqGmcB
****************************************************************************
UP VIBE CANDLE MAKING SUPPLIES
😎Soylite Wax Melter: amzn.to/3RFdDmE
😎Temperature Gun: amzn.to/3esTlhy
😎Heat Gun: amzn.to/3u5sbFY
😎Digital Liquid Thermometer: amzn.to/3KRBltK
😎Wick Trimmer: amzn.to/3wY4M7H
😎Stainless Steel Pastry Cutter: amzn.to/3wV9XVW
😎Heat Resistant Silicone Trivets: amzn.to/3es1cw8
****************************************************************************
Some links are affiliate links
**DISCLAIMER: Everything shared in my videos is from my own personal experience and is for educational and informational purposes only. You must do your own research and test your own products to ensure that your creations are usable and safe**
0:00 Intro
1:12 What is Titanium Dioxide?
2:08 Supplies for Making a Concrete Vessel Using Titanium Dioxide
4:55 Formula for a White Concrete Jar Using Titanium Dioxide
8:31 Pouring the White Cement into the Silicone Mold
12:20 Important info
13:50 Demolding the White Concrete Jar with Titanium Dioxide
15:30 Revealing the Concrete Jar
#WhiteCementJar #MakeConcreteJars #HowtoMakeConcreteJars

Опубликовано:

23 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 124

@BGMBliss 2 месяца назад

Love this!!

@CLDUA 2 года назад

Wow I really have to look into this and try to make these myself. You make it look super easy

@georginaledlie7444 Год назад

Yes, beautiful. Thank you. I would love to try this. Hugs.

@jesusmarin1489 2 года назад

Love the video and I love your energy. I learned a lot. Thanks for sharing

@upvibecandle 2 года назад

Thank you. I’m glad it helped. 😊

@altoonadesign9163 Год назад

Thank you for your videos. They are the most helpful to make cement vessels on RU-vid! 😊

@melindaduncan3073 Год назад

I appreciate your positivity. I needed that little talk today!

@upvibecandle Год назад

That's why this is UP Vibe... Too much negativity in the world... Glad it helped.

@jrmulroney 4 месяца назад

Love it

@camillemclean339 10 месяцев назад

I feel your vibe, I love watching your videos ❤❤❤😊

@upvibecandle 10 месяцев назад

Thank you.

@chancerlynch3130 2 года назад

I love this video! I actually just purchased my cement all at Home Depot today and my molds and both black and white titanium. I am going to look at your video with the sealing process! I did subscribe. I see your videos going far!

@upvibecandle 2 года назад

Aww. Thanks for the compliment 🙏

@solonyetski 2 года назад

You’re amazing, man

@upvibecandle 2 года назад

Thanks 🙏 I truly appreciate it.

@jesusmarin1489 2 года назад

Love it.

@upvibecandle 2 года назад

Thanks 🙏

@pamelacorral1151 2 года назад

Love it! I need some white titanium dioxide!

@upvibecandle 2 года назад

Thank you. There is a link in the description for the Titanium Dioxide.

@esmeraldalunalongoria7067 2 года назад

Love your video!!

@upvibecandle 2 года назад

I love your comment and you officially just made my morning. Thank you!

@sxmhandcrafted Год назад

FYI: You can tare your scale before adding each ingredient so you don’t have to rely on math. Great video as always Jai!! 🎉

@rockermia2011 2 года назад

I enjoy watching your videos, super interesting and funny! 😃👍🏻🌟🌟🌟🌟🌟

@SunflowerToshaDiys 2 года назад

I seen another person sprayed alcohol on the bottom to take the bubbles out. I love your channel ❤️ your energy and teaching its awesome. Have a blessed day sir.

@upvibecandle 2 года назад

Wow alcohol. I would never think to use it but if it works by all means... I wonder if it matters the percentage... Anyway thanks for the comment and lovely comment.

@triciaeugene8451 2 года назад

Excellent thanks

@upvibecandle 2 года назад

You are very welcome!

@anahimartinez3632 2 года назад

I love it

@upvibecandle 2 года назад

Thanks 🙏

@sarahalwix3869 2 года назад

I just discovered your channel and was giggling just a few seconds in. Your the male version of me haha. You rock!

@upvibecandle 2 года назад

Hey. Thanks for the awesome comment. Nice to finally meet the female version of myself.

@regntjejen 5 месяцев назад

Loving your videos as a beginner learning a lot. My question is how about pigment + TD + Cementall ratio? If we use pigment in the mix wouldnt it lower the cement all ratio and disturb integrity? And also do you press your vessels afterwards for solidity? Some of my test vessels break some not I dont know how to test them or if should I :D

@thatcraftypanda 2 года назад

You can actually zero out your scale between different additives! That's what I do when I work with resin or hairdye!!! This is so inspiring!!! My mold comes tomorrow

@upvibecandle 2 года назад

Thank you for your tip. I truly appreciate it.

@MoneyMimi 2 года назад

Molds are on the way

@christopherort2889 Год назад

Cool video. I'll do some if these tomorrow

@upvibecandle Год назад

Excellent. Let me know how it goes.

@christopherort2889 Год назад

@@upvibecandle I sure will. I do 2 tests. 1 with the 10% TD. 1 with the 5% TD. May be interesting to see how the shades look compared with each other. I will make an adjustment to the water in the 5% test.

@upvibecandle Год назад

@@christopherort2889 Remember each time you increase the % load of TD the vessel losses (PSI) compressive strength.

@christopherort2889 Год назад

@@upvibecandle Yep. That's why it's an experiment. I may use that mix and incorporate it into another mix. It may look really cool. We'll see how it goes first. Thanks.

@boutchou3539 10 месяцев назад

Hi Jai 😊 i really need your help. I follow your recipe for white cementall jars and its always stunning when i demold, but as the jar dries, i see grey coming back and i don't know why. Do you have an idea of why its happenning ? Thanks so much

@nit22999 13 дней назад

These videos never get old. I always go back to watching your basics vedio...every time I find some knowledge gems ✨ thanks for educating us. Much gratitude. Quick question. I see you are using your go to Amazon molds. Do you use any shape retainer ( dono what they are called) to have a consistent circle .Those 3d printed casing.

@upvibecandle 13 дней назад

Thank you. No, I don't use a support for the Amazon silicone mold. However, the silicone mold from Boowan Nicole, that I use as well, comes with a great support brace. Cylinder Silicone Mold with Lid 🌀 collabs.shop/c4gajm

@miss_k3602 2 года назад

All you need is a suit with question marks all over it😄🤣???? I love your energy

@upvibecandle 2 года назад

Hahaha. That’s awesome. Love it.

@jenniferrochaandrade2855 2 года назад

Hi Great Job!! Can you please do a video on sealant. Sealing your vessels. Pleaseeeeee.

@upvibecandle 2 года назад

Thanks for the compliment and video idea. I will be doing a video on sealants in the near future.

@EleonoraPetkovic Год назад

Hello, Loving your videos and the humor your bring into it!! :) I have a question, can I use only the white cement? Without plaster and white sand.

@upvibecandle Год назад

Thank you. You will have to test it as not all cement, sand and plater are the same. At the very least you will need sand to add to your cement. Watch this video it will explain why. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KCByTrXFXzQ.html

@EleonoraPetkovic Год назад

@@upvibecandle thank you so much , will do 😊

@patriciakoenig3966 6 месяцев назад

I've been using the same molds and when it's time to release the cement or what ever I happen to be using I have found with every one the top of my cement is not perfectly round what's up with that? It's like oval urrrrrr I'm so mad.

@gisselavarela5649 2 года назад

Hello ! I love Your videos . I have a question What function titanium dioxide has?

@jaicatalano2967 2 года назад

Thanks. It turns the concrete white.

@oluwaseunaddy940 Год назад

Great video 👍. Can I add another color to the mix?

@upvibecandle Год назад

Absolutely. Like in this video here. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yczZX6TzO3k.html

@melindalester2052 2 года назад

can u show how u make the vessel with the crushed glass on the top of vessel please

@upvibecandle 2 года назад

I'll add that to the list.

@INQUIRINGMINEZ 2 года назад

Have you ever used rapid set flow control in you mixture for the crevices and more detail

@upvibecandle 2 года назад

No I have not. Is it good? Should I add it in?

@INQUIRINGMINEZ 2 года назад

I find that it helps make the mixture more fluid with less water so it dries faster while still seeming very “watery”

@upvibecandle 2 года назад

@@INQUIRINGMINEZ Oh thank you. That's good to know. I will look into it. Thanks again.

@KisshaJ Год назад

Question, my mold is made for a 16oz candle how do I measure the amount of cement all that makes a 16oz mold?

@upvibecandle Год назад

Here is a video I made that will help you figure it out. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7jF2YLfI_OY.html

@user-fg4om8fm1e 10 месяцев назад

Another question. Do I have to seal the outside? I like the matte cement look better than the gloss. Nice rustic look.

@upvibecandle 10 месяцев назад

@esmeraldalunalongoria7067 2 года назад

How do you know how much of cement/water to add for that mold.I guess the question is how do I figure how much cement/water to use depending on the mold I would use?

@upvibecandle 2 года назад

I did a trial an error. I started with way too much and then slowly started to subtract 5 to 10 grams at a time until I was spot on. Also if you have Cement All you need approximately a 4 to 1 ratio of CA to water. Hope that helps.

@bijukurian7 2 года назад

He is so funny...hilarious....asking help from Alexa and passing the Maths exam....wow...where was this stuff when I was in board exam???

@CarolineDeKimpe 7 месяцев назад

Hi - bit confused on the percentage of titanium dioxide. in this video its just under 10% but in another video you mentioned only to use 5%. Can you please advise?

@upvibecandle 7 месяцев назад

No more than 5%. 10 is too risky.

@liviaribeiro655 2 года назад

Hi Jai. Thanks for the video. Question........How do you know how much titanium dioxide to use for each jar? I see you used 10% titanium dioxide from the amount of cement all you had. Globmarble has a video where they talk about how it is not recommended to use more that 5% titanium dioxide from the total amount of concrete because it lowers that PSI by a lot. Since these jars are for candles, the strength of the jar is very important for safety. What are you thoughts? Thanks!

@upvibecandle 2 года назад

Great question. When I first started I used 10% and then switched to 5% as going over that amount will start to compromise the vessel. So now 5% is the max I use. To figure out the amount to use just get your total formula amount and multiply that by 5%... and that will give you the amount to add in. Hope that helps.

@yvonnerod6276 Год назад

How would you calculate grams for plaster, cement, sand and water?

@upvibecandle Год назад

Here it is. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-JClrh1y9k4A.html

@thedreamingcure 2 года назад

hi, can you please tell me how i get stains out of your white concrete products?

@upvibecandle 2 года назад

I don’t quite know what you mean.

@Moonlightcandles.official 5 месяцев назад

Should I Preheat cement container 🫙 before pouring wax

@upvibecandle 5 месяцев назад

I don’t do that

@jellybelly083 2 года назад

Can you use titanium dioxide pre 630 and get the same effect?

@upvibecandle 2 года назад

I have never tried it. I read they are treated by different surface materials. 630 is treated with zirconium & aluminia, but 620 is treated with silica & alumina. With that said they both whiten so I would think you could get very similar results.

@erinotvos7813 Год назад

Anyone else’s Alexa went off during this? #350 😂

@upvibecandle Год назад

Hahaha!!!

@AshleySmith-up8kx Год назад

Hi I was wondering if I use the titanium dioxide in my cement all, then add like acrylic paint colors. Will it make them bright? Or not

@upvibecandle Год назад

Not necessarily. You can only use 5% of your mixture to whiten it.

@AshleySmith-up8kx Год назад

Thank you, Im super new to this and I’ve been wanting to make really bright candle vessels. It’s really hard without jesmonite, but it is really expensive so if you have any tips on making them super bright please lmk!!! Again thank you so much

@upvibecandle Год назад

@@AshleySmith-up8kx You can try painting them with white acrylic paint.

@dorothygedovius3488 Год назад

This is awesome but I have a question I seen other people just used plaster of Paris it came out beautiful with no bubbles but is it safe without cement?

@upvibecandle Год назад

Plaster of Paris is the weakest of all plasters and I wouldn't try making a candle with just POP. However, you can try other forms of plaster that should help you achieve your goals.

@dorothygedovius3488 Год назад

Thank you so much for letting me know I want to make it I will try them out one day..

@upvibecandle Год назад

@@dorothygedovius3488 Excellent. Yes let me know how it goes.

@Pilsner6996 Год назад

What is the difference between cement all and artisan concrete. Any experience with artisan? Thanks for the great videos!!!

@upvibecandle Год назад

Cement is a binding agent used in construction and is an ingredient of concrete. Artisan concrete is used for crafts and things of that nature.

@Pilsner6996 Год назад

@@upvibecandle So would artisan be an option for these candles you’re making? Or is cement all still the best option.

@upvibecandle Год назад

@@Pilsner6996 if you have access to Cement All then use that.

@michellegillie7428 2 года назад

How do you clean your bowls? I know we cannot use our sinks. Great videos

@upvibecandle 2 года назад

Great question. Because I don't have a lot of waste to begin with I am at an advantage. Then once I am done pouring I try my best to scrape out any residual product into my garbage bag. I then add water to my bowl and loosen the rest off. In my basement I have an unfinished section with a concrete floor similar to a garage floor that I throw the rest of the content there. When it dries it blends in with the floor and I start again. I hope that helps.

@michellegillie7428 2 года назад

Thank you!

@michellegillie7428 2 года назад

I still need to get control of my waste. I’m new to this and both times I’ve made TOO much! I want to start a small candle business but I’m so nervous. I’m terrible at math lol and this all looks so easy but it’s not!

@upvibecandle 2 года назад

@@michellegillie7428 It's very tough and very scary and the math is not easy but take 1 step at a time and build and grow from there. I am scared too and I mean that but like I always tell my daughter... Feel the fear but DO IT ANYWAY!

@user-fg4om8fm1e 10 месяцев назад

I like your channel :) I'm a little confused. I thought the TD or pigment is in addition to the cement all. Because you use up to a certain percentage of the cement all. If your adding the TD in the total grams of everything then your actually using less cement all. Isn't that bad for the integrity? Also you have me scared of selling my candles because of safety issue of cracking. What if someone ignores my safety sticker and burns it 4 hours and it gets really hot. Is it going to break and wax get everywhere or worse? I'm getting scared to do this.

@upvibecandle 10 месяцев назад

TD should be no more than 5% of your dry mixture. Anything more starts to compromise the integrity of your vessel. If you test your work thoroughly you shouldn't be worried and not to make you feel nervous but pretty much EVERYONE is going to ignore your safety sticker. The human race as a whole will do what they want, forget to do it or avoid it altogether. So, add the label, test your work get great insurance and let the world continue to rotate as it does and you should be fine.

@user-fg4om8fm1e 10 месяцев назад

:) @@upvibecandle

@georginaledlie7444 Год назад

Hi, I have question if I may please ? I bought a bag of concrete. On the packet it says I have to add sand. Have I bought the wrong stuff ?

@upvibecandle Год назад

It appears that you bought a bag of cement. There is a difference. Here is a video that will help you out. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KCByTrXFXzQ.html

@georginaledlie7444 Год назад

@@upvibecandle Thank you so much. Looks like I did an 'oops "! I will try again. Can I still use what I bought please ?

@upvibecandle Год назад

@@georginaledlie7444 You bought cement so you need aggregates to make concrete. If you have them then you can make concrete. If not then you will only be able to make paste.

@l.b.1952 Год назад

Lately all my jars break when unmolding them ...is soo frustrating, maybe I use too much water? I mix concrete with water. I do not use hobby concrete, you use "normal" concrete from the DIY shop :(....I leave them hours. I also make candle bowls from concrete, those work fine, but the silicone mold ones not....maybe its a bad mold?

@upvibecandle Год назад

That stinks. Watch my video on the reasons concrete cracks. Try less water or letting them cure in the mold longer. You got this!

@juanpabloadame3685 Год назад

Why do the parts that are up come out foamy? I make my containers with Cement All, Color Direct, and distilled water. Sometimes I use Titanium Oxide. I have a soft mix left to handle. But when it dries, the part that is exposed to the elements becomes porous.

@upvibecandle Год назад

I'm not sure why you are experiencing that. Are you sure you are measuring everything correctly.

@juanpabloadame3685 Год назад

@@upvibecandle yes

@allin181 2 года назад

Also, why dont you zero out your scale each time you add something? That way you dont have ro add up everything. Zero the scale after you put the empty bowl on it. Pour the 255g of cement. Zero the scale. Put 25g of titanium, zero the scale, add the water you need.

@upvibecandle 2 года назад

Great points. Thanks for the advice.

@MakeupMobster Год назад

Ok so I actually tried this the other day and something is wrong with the formula because it was wayyyyyyy too much water either I did it wrong or it was wrong on here! I was able to crush the vessel with my hands! I did something wrong. I use this formula, one teaspoon of TD per one cup of cementall. It usually works pretty good.

@upvibecandle Год назад

I never had any issues with it when I was using it. Now I use hydrocal and/or hydrostone.