You NEED these tools for Powder Coat, Vapor Blast and Zinc Prep! Yamaha TRI-Z 250 Part 5

Подписаться 238 тыс.

Просмотров 51 тыс.

50% 1

You NEED these tools for Powder Coat, Vapor Blast and Zinc Prep! Yamaha TRI-Z 250 Part 5
#yamaha #2stroke #vintage
Big shout out to you guys for recommending these tools and shout out to Rocky Mountain for sending them to me to try! You guys ROOOOCCK and I hope you're enjoying the series so far! 🤘
PARTS AND TOOLS IN THIS VIDEO - (These links may be affiliate links that I get a kick back for; there is no added cost to you)
TIRE LINKS
Maxxis RAZR Tires - cuts2.com/eEAdM
SunF (RAZR Knockoff) - ebay.us/1B90Pn
ITP Holeshots - cuts2.com/AsDvj
Reaper Tires - ebay.us/8TxfhH
Carlisle Fast Trax - ebay.us/lnfcGR
Wanda (Like Turf Tamer) - ebay.us/nDDPkJ
OTR 350 Mag - ebay.us/fHGOKm
OTR 38 Special - ebay.us/MivLWb
OTHER LINKS
Stud Removal Tool - cuts2.com/CmlCT
Dowel Pin Remover - cuts2.com/DltHn
T Handle Allen Wrenches - cuts2.com/kSEVT
Blind Bearing Puller - cuts2.com/Ulqzx
Orbital Sander - ebay.us/9JrRpf
Bench Sander - ebay.us/dIOnOZ
Mini Clamps - ebay.us/1maGO5
Stainless Brakelines - ebay.us/N0ance
BVC Fork Conversion Kit - cuts2.com/IydGC
Blow Torch - amzn.to/45H1Pbg
Mobile Work Bench - ebay.us/PnYKOq
Drill and Driver - amzn.to/43kzIwW
Milwaukee Hacksaw - amzn.to/45E8V0h
Die Grinder - amzn.to/3qj9dJv
Sanding Discs - amzn.to/3OP8HNP
Large Clamps - amzn.to/3CaWjQC
LED Headlights - amzn.to/42aXPww
SPONSORS/COMPANIES I TRUST
⬇️ CUSTOM TRIKES SXS, ATV'S & MORE ⬇️
BVC Offroad - bvcoffroad.com/
⬇️ OEM PARTS, PLASTICS, BEARINGS, SEALS ETC ⬇️
Rocky Mountain ATV MC - bit.ly/32OHs02
⬇️ POWDER COATING ⬇️
Bonehead Performance Coatings - boneheadperfor... (Mention my name and get 10% off)
⬇️ SUSPENSION ⬇️
Rocket Ron - www.rocketronra...
⬇️ CASE SAVERS & SKID PLATES ⬇️
DRW Performance - bit.ly/34dxWEp (Code SABO10 for 10% off)
⬇️ PREMIUM BAR CLAMPS & THROTTLES ⬇️
Urmosi - urmosi.com/
⬇️ USED PARTS & REBUILD SERVICES ⬇️
Power Sports Nation - www.powersport...
⬇️ VAPOR BLASTING & ZINC COATING ⬇️
MotoBlast - www.njvaporbla...
MERCH - michaelsabo.com/
Add me on Instagram @michaelsabo350 for Channel Updates!
Companies and Sponsors please contact: michaelsabo350@gmail.com
I own the license to use any and all music in this video.

Опубликовано:

13 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 271

@MichaelSabo Год назад

Big shout out to you guys for recommending these tools and shout out to Rocky Mountain for sending them to me to try! You guys ROOOOCCK and I hope you're enjoying the series so far! 🤘

@michaelmain1990 Год назад

Use the reapers for the tires, they slide well. Atleast on a zero turn, when I use to mow professionally we didn't like them that much for hills because we were driving at a 45 to 55 degree angle

@hobbs37110 Год назад

Well now you gotta name it Dirt Ball

@MichaelSabo Год назад

@@hobbs37110 😂😂😂

@abbybonilla4511 Год назад

The best way to wind down after work/school is beer and BCG.

@mikebarriball Год назад

Hell yeah mike, I'm enjoying it all the way, bro''

@daveb4mv Год назад

I know it gets said a lot dude, but the effort you put into these vids and the quality of them is really top notch.

@MichaelSabo Год назад

Still always means a lot man; thank you!

@user5.56 Год назад

aww

@jameschitwood5962 Год назад

Really impressed how far you’ve come from your fist videos man! You can see the hard work and progression. Great job Mike! Keep up the good work!

@MichaelSabo Год назад

Much appreciated James; thanks for being around for my older content too!

@sfr2929 Год назад

Pro tip mike, put valve lapping compound on the dowls before you install the puller, helps it bite and not slip off the dowl

@blessedinjax Год назад

I think those lawn mower tires are bad ass or would be for this 3 wheel build

@blakecarpenter219 Год назад

😂 loved the info commercial bit. That's what makes you a step above the rest. Going that extra mile for your viewers.

@MichaelSabo Год назад

Haha, glad you liked it and thank you for the love!

@Shadowz_660R Год назад

🎉🎉🎉 Dude we dont care what your fixing as long as you film it and drop a video we are good 😂 Are you still going to drop the raptor full engine build video?

@MichaelSabo Год назад

I appreciate that Jose! Yes, that video will be posted; thank you for the reminder!

@Shadowz_660R Год назад

@@MichaelSabo For sure dude. I'm in the process of building one. So far I got the bike fully stripped, blasted the frame, welded a lsr gusset kit and got the frame back from powder. Now I'm working on cerakoteing the engine, all the blasting is done just need time to actually paint them.

@MichaelSabo Год назад

@Jose Calas sounds like a great build dude! I will try to get the engine build video up sooner than later.

@Shadowz_660R Год назад

@@MichaelSabo Yeah man it should be a nice build if I can translate what's on my mind to reality. 686 11-1 cp piston, carrillo rod, port and polished head, +1mm valves, beehives springs with titanium retainers, stage 3 hot cam, +4 curved stellar swingarm, I contacted full flight to see if they could make me a set of Arms like yours to run the yfz 450R long travel shocks, they were great and made them for me. I appreciate you giving them the measurements on the A arms and for all the replies man seriously.

@blessedinjax Год назад

Thx for the update about the new tools Makin life easier should be everyone’s goal If not for your videos I wouldn’t have a clue Now I’m a pro lmao

@MichaelSabo Год назад

Hell yea dude, I'm glad you've learned from my videos 🤘

@v73w85 Год назад

Your mud ball was a “Dirt Dauber” nest. They are a type of wasp but many variations of them don’t sting or are just not aggressive. They are kinda loaners and just make these nests to incubate their larvae

@Berm_Blaster Год назад

I love these little random tools that make the job so much easier. Sure vise grips can get dowels out but it ruins them and there’s just something satisfying about using the right tool.

@MichaelSabo Год назад

Very true man, and you don't have to worry about scoring the cases with the right tools

@vintagetrikesandquads4012 Год назад

Love the comedy bit about the dowel remover.

@kylemay2735 Год назад

Great Video Sabo! Little tip for a neck bearing race or a blown out wheel bearing that leaves the outside race. Run a solid bead of weld and that will shrink the race. Will almost fall out. Little tappy tappy with your purse will help send her home 👍🏻

@Primerk5 Год назад

yea I was going to suggest that too

@Charles53412 Год назад

BulTaco Mike ! I love how you pay homage to BulTaco ! A lot of the younger generation has never heard of a BulTaco let alone ever ridden one. BulTaco !!

@mikebarriball Год назад

IN THIS BUILD YOU CAN SEE HOW MUCH WORK REALLY GOSE INTO A BUILD LIKE THIS. ALL THE LITTLE THINGS, ALL THE REPAIRS, AND MODIFICATIONS YOU DO. YEAH, I CAN'T WAIT TO SEE THE END PRODUCT, AND TO SEE WHAT YOU ARE GOING TO DO WITH IT. 🏁🏴‍☠

@giosansone1457 Год назад

Man, those darn wildfires

@j.need4qlife483 Год назад

Michael, I watch your videos so much and have actually purchased the tools you use after watching. I am now finding I need to get a much bigger tool cabinet. Thanks for the inspiration.

@Jugger_Nutt Год назад

I'm voting on the first lawn mower tire, the reaper. It looks GREAT.

@billythebandit7480 Год назад

Good work love the content mike !!

@MichaelSabo Год назад

Thank you Billy!

@g.p.880 Год назад

That infomercial was done to perfection lol so funny.

@williamneske6452 Год назад

Best way to start the week right here🤘

@MichaelSabo Год назад

I appreciate you Will 🤘

@Cartduckmann Год назад

Btw thanks for being so dilligent! Watching these make me happy :D

@MichaelSabo Год назад

Thank you for watching them and supporting what I do!

@timkwasnicki Год назад

You need to open an advertising agency!!! 😂 best tool commercial I’ve ever seen!

@joniripatti154 Год назад

So pumped about this build

@lucascady4992 Год назад

That dowel tool is Badass!! Very impressed!

@SquirrellyDan88 Год назад

Lmaoooo! The whole ass commercial for the dowel pin remover was great! Need more of this!!!!!

@frankkrezel7922 Год назад

Anotger work of art!! Love the little comments and jokes! Cant wait to hear the tri z fire up. Keep up the great work Mike!!!🤙

@MichaelSabo Год назад

Thank you for the love Frank!

@MrAlternation Год назад

i love the last part of this video, you showing the tire options and stuff you are thinking of ordering, just feels like were chilling lol

@Jonny2Fingers Год назад

I'm so excited for this build! The yellow rad hoses are a nice custom touch. The price tag is worth it especially since it came with free stickers.

@mikewisher4083 Год назад

Tri-z it's cool to see u doing it . Even better to see some of these companies working on older machines keeping them alive . Can't wait going to be badass

@theglitch99 Год назад

👍🏼 always enjoy your videos, thanx

@Jdouglas999 Год назад

That dirtball was a mud wasp nest aka dirt dauber. Great idea welding that steering bearing race. I've fought with those for hours before. Never thought of that. 👍👍👍 Thanks!!

@lanniewiant8269 Год назад

I can't wait to see this done its gonna be great

@jadryanrosario403 Год назад

I had my 89' blaster powder coated by a good buddy of mine Peter Amato here in michigan, a great guy and he actually showed me the clear coated vin trick and honestly it looks TRICK!!

@christopheravery5808 Год назад

That was a Mud Dobber that made a nest in your exhaust. They are little black wasps with a blue tint. Typically not aggressive, but they make nests in places that can cause problems. Anyway, awesome job on the headlight, and that was a freaking awesome idea to get the neck bearing out. I’ll have to remember that for the future.

@MichaelSabo Год назад

Thank you man, just be careful not to weld the race to the frame 😂

@christopheravery5808 Год назад

@@MichaelSabo oh yeah, that would NOT be good 😅

@malibusbc Год назад

Yep exactly, we have them get into everything in the south. I couldn't get my echo back pack blower started one day, plug was wet but was getting spark. They filled a small muffler completely solid.

@christopheravery5808 Год назад

@@malibusbc I’m in Tennessee, if you leave anything outside that they can get into they can and will make a nest in it, as well as on every single brick building lol

@RealSuburbanCowboy Год назад

Freaking love the channel. You should buy your own vapor blaster. It's such a great too to have. 10 minutes at 200 degrees in your gas grill and bearings will pretty much fall out of cases.

@MichaelSabo Год назад

That's facts man! I usually do the oven but sometimes they just fall out; great info!

@ryananderson3856 Год назад

Love the camera transitions and editing, awesome video 👍🏻

@ThAtGuY-u9d Год назад

I can fully weld, reinforce and machine that case back to spec if you’re interested. No cost, I appreciate what you do and want to help out.

@MichaelSabo Год назад

This is a very generous offer; I already dropped the cover off at my coater but it may not be coated yet. If you like, send me an email and maybe I can send it to you - michaelsabo350@gmail.com

@kylekallies3381 Год назад

I guess if you want different lawn mower tires are definitely that would love to see you do that just to see the review on how they drive

@Shitty_Shit_With_Anthony Год назад

Man this dude has inspired me to build up my first dirt bike frame i love the vids alot

@ni_wink84 Год назад

6:06 😂😂😂 man I missed this type of stuff on your Channel, always gets me cracking up! Really like this build, I’m super excited to see it all come back together. Amazing video as always Mike!

@MichaelSabo Год назад

Haha, glad you liked the infomercial. Thank you as always bro!

@-jeffreybollenbach- Год назад

Now that is some great work. I'm really impressed, I know I couldn't do that. Thanks for the video man. Love it

@richhilton155 Год назад

Another awesome video Mike! Can’t wait until the full build! God bless!

@johnstancato8785 Год назад

Mike when you have a phillips-head that stripped out take a grinder and cut a slit in it and use a flat head screwdriver to get it out 👍

@shamblershamfam3597 Год назад

That is a spider pinata! I'm in Florida. The dirt dobbers are relentless. They will build in or on anything that sits still for more than a day.

@RECURT Год назад

Mike I have learned so much from you, you have inspired me to start doing these types of things just yesterday I finally got me a Yamaha warrior 350 to work on

@FatHulkRideEbike Год назад

In the 80s I would put Cheng Shin tires on my bikes because they had good tread patterns and they were an economical tire. People would always give me grief about it lol. Those same people today probably drool over Maxxis which is owned by Cheng Shin. Also on many bicycles and ebikes they have "CST" tires (Cheng Shin Tire). I believe CST is the largest bicycle tire manufacturer in the world. I feel some vindication lol.

@MichaelSabo Год назад

100% man! I actually just learned this past week that CST was Cheng Shin.

@gowengetter4599 11 месяцев назад

My favourite channel on YT Congratulations on building this up

@mitchellstepan7215 Год назад

You can always tap the dowel as well and use washers and a bolt to pull the dowel out. Can reuse the dowel too. This is the way I’ve always done it. I’ll probably buy this tool now though, thanks haha!! Great vid man

@MichaelSabo Год назад

Not sure what the washer and bolt method is but there's no doubt this is the easiest I've been about to remove an old stuck dowel; I'd say you'll be happy with it if you get one!

@bobbyroberrrt579 Год назад

Love the new tools definitely have to order me some!!

@MichaelSabo Год назад

Thank you for supporting man; they really are good tools to have

@nunyabizzness5477 Год назад

That stud tool is trick. The left cylinder base studs are discontinued, but the right are allegedly still available if you need any. That dowel tool is REAL trick! Those look like the original transmission bearings. They should have "NSK" "07L" and "TM205", it looks like, from the picture on Partzilla, on the seals. Certain Hondas use a sealed bearing, but only sealed on one side. It's to try and keep transmission oil in them. The almighty 1992-2001 CR250Rs use that tech, and I think the 1984-1986 CR125Rs do too. I know JB Weld works on rusty, glassbeaded steel that is then primer powdercoated, wet sanded, and color powdercoated. Nice and smooth. Looks like you're going to have the cover mini texture black powdercoated. I'm worried about there being pinhole leaks there though. That headlight bracket is gonna be bitchin'. I'm looking forward to seeing the LED fabrication part! Wow. Obviously, Yamaha never intended the steering stem bearings to be replaced...

@bigfootandbananaman4746 Год назад

With those Reaper tires, I mowed grass for years and some mowers had those. They do not have much more grip than standard turf tires, so they would be great for sliding around, but they would be pretty bad in wet conditions.

@MichaelSabo Год назад

Thank you for this feedback; that was my worry, is that on messy trails they'd be worthless lol

@markwarren3590 Год назад

That stud removal tool looks really good some are so weak and that dowel tool with the slide hammer was cool af clever idea, I've had best results with once I get the stud moving to keep going backwards and forwards a few turns at a time

@cletusbowling923 Год назад

Love the mud dobber in the DG exhausts silencer

@LP_LIFE Год назад

It’s a mud dobber, love ur videos

@nelsonkarrer6961 Год назад

Good choice on the rear tires

@johnjmar609 Год назад

I live in south jersey and the razors we used were perfect in the sugar sand or gravel but gripped hard with grass

@thegrimreeper3141 Год назад

yeah the fires are bad down here one near me I'm glad they put out plus the week worth of rain helped to

@josephgentilejr9059 Год назад

Great video, have fun in OK , look forward to upcoming videos 👍🏻

@virgilpayne2804 Год назад

Another way to remove inner races is to run a weld bead on the race where the bearing rides. Once it cools it will contract and “shrink” the race and it will come out much easier. Sometimes just fall out.

@exitzsplxtzyt6526 Год назад

Finally been waiting for this video

@DustinDoesStuff Год назад

To remove that race, all you gotta do is weld a continuous bead around it. Once the weld cools the race will just fall out of the barrel.

@MichaelSabo Год назад

Thank you for the tip! I think just welding on it is part of the reason it punched out so easily.

@jadonanderson8080 Год назад

Hey Mike just a reminder you should use a low profile tire for the rear something like a Honda 400 tire and make sure it’s OEM

@MichaelSabo Год назад

Not sure if you made it to the end but I chose 20x11x10 Razr's. Front will be 22x7x12. It will be about 2 inches lower than stock.

@jadonanderson8080 Год назад

Yeah I saw the tires you were going to use but I personally would recommend a looser tire for traction otherwise it will grip really hard when you’re trying to turn

@sayers_repairs Год назад

There is a filler, I believe it's called Lab metal high temp and can fill in the pitting from the Weld and also be powder coated. This process was done on one of my aluminum fuel tanks with great results.

@banginheep Год назад

Truth. Having worked at a powder coating shop for years high temp lab metal is the only filler that will hold up to the heat. Several companies also make low cure powders that can cure at 350deg which helps keep fillers from melting out.

@calamitycycles5994 Год назад

Whatever tire you get on a three wheeler, my experience is less traction the better. And light weight is a big factor too. Good luck my friend

@williamcoddington9662 Год назад

Lawnmower tires are fun and oddly turf saver tires are decent in snow but id spend an extra couple bucks for actual off road tires or something but they work great for ripping around the yard and not tearing everything up

@jordanpanich Год назад

Looking awesome!

@ScaleRacingChannel Год назад

Mud Dauber nest in the exhaust. I've had many of weed wackers mysteriously not run the next time out due to these little buggars setting up in the exhaust.

@MichaelSabo Год назад

Ahh, thank you for the info man! They're not that common around here but these TRI-Zs came from across the country.

@Bri-tg6xr Год назад

We could smell the smoke in Maryland at one point so pretty crazy. When that exhaust literally took a dump on your work bench, I died laughing. The work you do is so primo and I need those skills for some of the crap I buy too. I'm pretty sure I've seen a powder coat safe filler that you can use for those pinholes.

@askmeaboutarcticcats Год назад

Can run a continuous bead of weld On the bearing race to get it out. The weld will make the race shrink when the weld cools And they come out super easy.

@mikedahoe2251 Год назад

Lol did not expect the plumbing and archeology!!...Yu made a bunch of lame routine chores fun! Cool vid

@Redrummk2 Год назад

Cant wait to see it done

@jefferybye2169 Год назад

Thanks Sabo for another great educational video from Dr. Cycle.. I cant wait for the next one..And isnt it crazy about all that smoke from Canada, Im in Pennsville NJ and we had it bad here too, I hope you and your Dad have a awesome Father's Day.. You rock 🤘🤘🤘🤘🤘🍻

@davidstoner27 Год назад

Have a safe trip bro

@MichaelSabo Год назад

Thank you dude! It was a great one.

@davidstoner27 Год назад

@MichaelSabo ya it looked like alot of fun from your Instagram

@frankkrezel7922 Год назад

Just change my profile pic to my TRX700 🤙👍 keep ‘em coming Mike!!

@samrehl Год назад

Great video Mike

@FilipHnizdil Год назад

When im restoring a old quad like blaster now, i love using old dunlops like kt335 and kt331 from 660 bcs they have the old quality of japan and in suits the style of made.but they are hard to find in good condition.

@richknight7307 Год назад

Great bud again as usual and love the razrs but just wanted to say I have the sunf knock offs on my warrior they’re pretty good and close enough for the price

@floridatrailrider305 Год назад

Great job on that clutch cover,definitely going to get that dowel pin remover. Looks like a great tool.

@MichaelSabo Год назад

Thanks man, hopefully it will be decent after coating. The tools are great!

@darrenstansbury6431 Год назад

Hey Micheal, I hope you get this, you said something about getting surgery on your rotator cuff, have you heard of QC Kenetics? It’s an all natural healing and it works. I had a torn muscle in my left shoulder and rotator cuff messed up in my right shoulder. I did the treatments and no surgery and didn’t miss one day of work and they want you to use your shoulders. I have no pain at all and can put both my arms above my head. Check it out. NO SURGERY! It works. I love your videos

@samphilipp4997 Год назад

That was awesome man 👍

@tristan_andrade Год назад

Never click that fast before 🔥😂

@MichaelSabo Год назад

My maaan, thank you Tristan!

@patty2Strk Год назад

gonna be sick !

@tykebrandt-lh2bv Год назад

Love the videos! Glad you put so much work into them. You’re very underrated. Hope the channel grows more. Keep up the good work!

@pbag26 Год назад

How come every time I watch your videos, my tool cabinet keeps getting cramped. Waiting to see everything come together. Love the videos!

@jarrettbutcher3082 Год назад

Love the vids❤

@MichaelSabo Год назад

Thank you Jarrett!

@eshott396 Год назад

I loved my GNCC tires/ I’m doing TT they hooked super great but slides just to little.just hooks. Did Hoosier tires amazing! And holeshot are good as well!

@Buck.short.builds Год назад

You need to buy vampliers they are the best pliers for stripped Phillips head screws ever they are amazing!

@tykebrandt-lh2bv Год назад

Love the videos! Glad you put so much work into them. You very underrated. Hope the channel grows more. Keep up the good work!

@michaelcoffey2589 Год назад

Lol I have sunf tires on my Polaris scrambler 500 4x4 and they slide well and will hook well they are very predictable when you are riding the machine Love the videos keep up the good work

@DerredmaxTRIAX Год назад

Good stuff!!

@MichaelSabo Год назад

Thank you bro!

@patrickadlam6888 Год назад

For tires u could look at the Duro HF-244 Desert X-Country Tire

@TeamHeresy 7 месяцев назад

What you found in the muffler is a dirt dauber nest, they eat spiders and make nests out of dirt. We have them here in Louisiana.

@snapfish89 Год назад

We got the smoke down in southern Illinois also.

@YerzengaPerformance Год назад

Great video Mike. As a long time Aluminum TIG welder, that weld was just about as good as it could have been for that part soaked in oil. Taking it down only guaranteed to reveal the porosity. But there is a high-temp body filler fix for those tricky porosity situations. Just braze in brass, lead or even the lead/tin mixture. The brass will likely be harder than the aluminum so it will also present challenges for finishing. But the lead works really well and is easy. Keep up the great work. Can't wait for the next one.

@MichaelSabo Год назад

I really appreciate hearing this from someone with experience. I am hoping after the texture powder is done, it will look decent but if it really needs it, I may take it back down and try brazing it like you suggested. Thank you

@YerzengaPerformance Год назад

@@MichaelSabo Unfortunately it may make it impossible to braze properly if that coat gets down deep into the porosity. The quality of the brazing is based completely on surface tension. And the surface tension can only be acquired from a clean and fresh surface. Aluminum brightener that the truckers use on their wheels is a good intermediate acid that will etch it well to attack it properly before welding or brazing. Just rinse and bake thoroughly after using it. This brightener can be found at NAPA auto parts and doesn't break the bank.