I bought the Kingbolan BM550 on AliExpress however it didn't indicate any of my new or in service batteries as Good (yes I did set the tester to the CCR battery ratings). I tried to complain to the AliExpress seller, then AliExpress To no avail. I won't be buying from AliExpress again.
It's 2024 so if anyone is watching this video you do not have to take off the front bumper you only have to take out the right headlight remove the cover that's in the right front wheel well for the supercharger cooler there are two screws that holds in the housing for the cooler and then you can access the part that you're trying to remove
When painting the panel I would probably of keyed the entire panel with a scotch pad, masked off just the door, window, bumper and boot. Then blended the silver paint out over the rest of the panel so you don't get a hard edge. Silver is a massive pain to blend as it is. Or do all the prep work, metal work and get a paint shop to spray just that panel.
I have the same rust/corroded area on my 2007 A6, I have looked at a load of “how to” videos and yours is certainly the one that is giving me the confidence to start cutting, shaping some sheet steel and make a new rear bit for it. Thank you and I hope mine turns out as well as yours does on the metal work/ welding. Dont worry about the paint. It protects at the end of the day
Thanks so much for this great video. I had a PSACN error code and stuck on SRS light and feedback was "rotary coupler" - even though the horn was working. This helped me change it out on a 97 MGF. A few differences and I found I didn't need to remove the horn buttons just the connector. Super, super helpful! 👍
Just found your channel, Great video'. I tried welding for the first time yesturday which was fun and in a few months I will be tackling the rusty sill on my Daewoo Lacceti. Keep up the good work.
Great Videos - Just discovered your videos in time for starting the compressor replacement myself (independent RR specialist replaced one last year but don't wanna pay their £150 per hour(plus tax) hourly rate and like most of my cars I figure once I have done it once it will be good experience should I need to do it again.
Hello Brother. Nice repair! On the finish paint, maybe mask off to seam lines, then when painting, do a bit of dusting of the paint, where you will actually get paint over the whole panel. However, dusting over and over, time after time, until the blend disappears. Otherwise, nice job! You're 😎 not afraid of negative remarks. I'll back you every time!! Thanks 😉
Removing the battery leads with engine running can gouge a hole in the budget when you have to replace expensive electronics of the car. It isn't a 1940's tractor with no electronics , even on that one you can burn the ligtbulbs or the power generator
I wrote to you a few days ago. I meant the service manual for the MG TF. Could you at least send me the title and publisher, or where to buy it? I also have such a car and I renovate it myself. Best regards, Robert Meikson from Poland
One problem that I see with this charger when used as a float charger on a bike or a car is that it appears to me that if grid power goes off/on the charger would restart and wait for you to press the button. Am I missing something? BTW, I have been using a CTEK MXS 5.0 on my BMW 330xi when it's not being used for years now. I love the CTEKs.
you wana know why you have a f transmission fault etc... someone put in a plug connector sleve... and it's actualy an upgraded sleve the dealer made and it has to be pushed really tight while providing back preasure while clipping the reciever onto the clip... sometimes you can't get it clipped on all the way
I’ve recently picked up a l320 tdv6 so only just found your channel. I love the way you tear things down and explain fully as you go along, by the way you analyse things I’m guessing you have some sort of engineering background? I don’t have the tools or space to attempt this but it’s great learning how by watching you work! Keep it up 👍
This video shows that simple Range Rover repairs aren't all that simple. He planned to fix the suspension, now he has to pull off side steps, the grille, the headlight, he practically took the whole car apart to fix the suspension!
Hello. I replaced my timing belt on a TF 2003 after watching two tutorials. One question: I couldn't find a mark on the crankshaft pulley? I couldn't align the camshaft pulley markings! After making marks on the belt to be disassembled, I aligned them with the new belt. When I tighten my new belt tightly I have a gap tooth on the crankshaft pulley. The engine runs smoothly but the idle tends to stall what to do thank you
Sometimes because I don't drive my L320 much the battery is low, which causes 3 faults, suspension orange error, HTC transmission error and parking brake, after I drive it ,then turn off and back on clears the faults
Hi Lee. These videos on the MGTF series have been a God send for me! The fact that you include every single detail really sets you apart and is incredibly helpful as I work on my own MGF Many thanks for your hard work and commitment to show the whole process. All the very best, Steve
Klw baterenya lebih dari 6 AH, bisa ditest, mbak ! Klw kurang dari 6AH gak bisa dilakukan pengujian. Makanya untuk membeli alat test batere sejenis, harus dilihat spesifikasinya terlebih dahulu pada deskripsi produk, apakah alat test batere tersebut bisa untuk batere dibawah 6AH atau tidak, baru kemudian membeli alat test tersebut, bila sudah yakin alat tersebut akan bermanfaat untuk kita gunakan.😄
This tester is 30AH to 200AH. It will work only for voltage reading but CCA it won't be accurate. With smaller motorcycle batteries less than 30AH. For that I would recommend Autool BT360 Uni-t ut673a Lancol micro 200
