Thank you very much for the time you spend making these videos

Great job Dad! That’s the best way to train and make memories!

😎👍🇺🇲

👍

Cutting edge

if we had 5 dollars for every time we hit our self's hammering we would be rich

wow that is some A+ number one work... amazing ... just wow ... it looks factory .. you sir are one hell of a welder !!

What I find interesting is that you are welding a steel plate onto cast iron. Your using MIG, so I am imagining the use of the pin scaler is to impregnate filler into the cast iron? I have an old Oliver tractor with a hole in the block - wonder if I could use your technique to patch it.

I always like your choice of music love your videos

This dumbass makes a 21 minute video and doesn't check before hand to see if he has any silicon brass rod, which he didn't. Quite the amateur film maker!!!!

ah you need some figure 8 calipers to measure that thickness. Thanks for sharing

RU-vid is why I hardly watch any television. Your videos are one of the reasons I watch so much RU-vid! Keep the good stuff coming!!

What are the power requirements for that Lincoln MIG welder that you used in this video? I assume that you are powering it off of your Miller gas powered welder. Does this serve as a really good alternative to a suitcase wire feeder? Because let's face it, those suitcases are expensive!

Big steel big welds. Right on.

I know it was a crappy job, but I would rather you do it right than someone else tacking it on. If it did come apart, people could get hurt. I am glad you did it.

Well done isaac

Isaac, the best thing you can say about your joke telling is you don’t talk much when you weld.

After those jokes you could have just as easily turned off the camera and not lost the viewership. We would’ve waited. This video has been painful. But not bad enough to turn away.

That C style Lenco ground clamp is a serious clamp. I need to buy one also.

Bro, been welding for over 125 years, worked on the Titanic ..you are awesome. Great video my friend..i have learned so much from ya😂

You should have some brake clean in your truck I've used it a lot molding up oil pans on vehicles

Perfect. Thanks for the videos.

At 33:00 just as you start gouging there's a spark shower behind the bucket - top right corner of the frame- what's that?

Great size fan in that older unit.

I'm ashamed of the engineering on the track. The track takes all the load and punishment of the machine to the ground. Of all places to go minimum metal strength. The track system is not one of those places. Hopefully, the other side doesn't fail soon for the customer. Have a happy 4th of July, everyone.

I like the new Hypertherm Plasma torch. Great repair! Next week you get to do the other side. Thanks for the video.

You are lucky because the frame and the tube is seted themselfs in a correct angle at the siting position. This issue is run out the field service range, all the folks lucky by twice, because the pin is can not come out , when the frame is stand. Try to not be a hero and u last longer with that amaunt of luck!

👍👍😉

Well done. Where is your Minion??? Be good and be safe.

Very good job 👍👍

This was a challenge? This was every day life for a welder.

Thing #1 and thing #2? Both using Harbor Freight grinders. LOL

Issac, wonderful video, that new Hypertherm torch head looks super duper handy...... I had seen them at the LWS, but did not really think about the ease of getting into such tight places...that was tight as a crab's ass in there, Water Tight !!!! Have a wonderful 4th of July, Best Wishes from Orlando , Paulie Brown

Another fixed _broken banana_ well all I can say is that will be _a peeling._ 😲🤦‍♂️

Dock cranes on a rolling yard , Genius 😖

34:40 why do you do that “pulsing” method? I’ve seen you use that method before and always wondered why. Thanks

Isaac at his trickery again! Good job 👍👍

Yes

Exactly! Why not😜

That thing is big

Great video! Good work

The best reality chanel ever. I keep this thing for a while: when an tool was fall just before the critical operation was start, there is a signal to not do or not do that way.

Hİ IC. Could you try arc gouging with steel electrod like 7018 and blow the molten metal with regular air gun? It may be the first on the internet.

Hİ IC. Could you try arc gouging with steel electrod like 7018 and blow the molten metal with regular air gun? It may be the first on the internet.

That had to be one of those 5k Chineseium excavators. That frame looks brand new no rust. No wonder there so cheap there made of low grade tin foil.🍻

Hell yeah!! Making it happen

This is a lot of force on that flange with no gussets to help keep it from breaking off with a span that long.

👍👍🇺🇸🇺🇸🇺🇸🇺🇸 have a safe 4th

Thats not good when you have to weld it to take it apart lol... It's usually the other way around