1992 Cadillac Fleetwood - Misfire, Rough Idle, Poor MPG (Shorted Injectors)

Подписаться 423 тыс.

Просмотров 41 тыс.

50% 1

This is typical of early GM fuel injectors (multec-1). On the 2.8L, 3.1L and 3.3L group fired systems, one shorted injector will cause a no start! On the sequential engines, like on this Cadillac, misfiring and rough idle is the typical complaint. Be aware of replacement parts and the characteristic differences you will see in a current ramp waveform. For you scope guys out there, this type of thing can have you barking up the wrong tree.
Related videos:
Rough idle, MAP code 33, intermittent no start (shorted injectors) - GM
• Rough idle, MAP code 3...
How to test for shorted fuel injectors (1987-1994 GM Cars)
• How to test for shorte...
How to interpret fuel injector waveforms (a ScannerDanner Premium video)
• How to interpret fuel ...
GM 3300 Intermittent no start rough idle (shorted injectors) part 2
• GM 3300 Intermittent n...
ScannerDanner Tools:
www.scannerdanner.com/tools.html
www.amazon.com/shop/scannerda...
For more information on this topic, I have written a “field manual” called Engine Performance Diagnostics which is available at www.scannerdanner.com as an eBook or paper book.
Want even more diagnostic training? Whether you are a DIY trying to fix your own car, someone looking to become an auto technician, or a current auto technician that wants to get more into diagnostics, subscribe to ScannerDanner Premium www.scannerdanner.com/join-sc... There is a 14 day free trial.
On ScannerDanner Premium I will bring you right into my classroom at Rosedale Technical College. You will find page for page lectures taken right from my book as well as exclusive classroom type case studies. What is so special about these classroom case studies? I pull live problem vehicles directly into my classroom and we troubleshoot them in real time, using and applying the theory and testing procedures we learn during the classroom lectures. There is no better on-line training of how to troubleshoot automotive electrical and electronics systems anywhere!
Disclaimer:
Due to factors beyond the control of ScannerDanner LLC, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ScannerDanner LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ScannerDanner LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ScannerDanner LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ScannerDanner LLC.

Авто/Мото

Опубликовано:

9 июл 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 246

@ScannerDanner 3 года назад

Related videos: How to interpret fuel injector waveforms (a ScannerDanner Premium video) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-4mut0Lpg5k4.html Rough idle, MAP code 33, intermittent no start (shorted injectors) - GM ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-iIO-2LmwkdY.html How to test for shorted fuel injectors (1987-1994 GM Cars) ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ssxuR5At6Io.html GM 3300 Intermittent no start rough idle (shorted injectors) part 2 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-vmutNjx7QDY.html

@1202Sid 3 года назад

If not using the snapon scope and you don't use attenuator, will it damage the scope or just make the readings worthless ?

@HOTRODRICO 2 года назад

Mr. Danner I love the content, however, as a guy who's been watching your videos for a long time, the new over usage of editing it making the video super jittery, cutting to the next clip or scene every 5 seconds is making me dizzy, also the darker cinematic effect is making things feel like im high watching this or am wearing sunglasses in my house lol I kinda miss the raw natural vibe from your earlier videos, yea keep the HQ 1080p and everything but the over polishing is unnecessary, that's not why we fell in love with your videos, its your expertise and ability to teach, please understand this is not a knock on you or your son's abilities obviously he's become a pro with the software and kudos to him for that.. but its kinda like the original texas chainsaw massacre that was gritty, raw , almost made you feel like "is this real?" vs todays versions where its so prefect and clean and everyone is a model with oil of olay commercial perfect skin that it's not scary anymore... if that makes any sense cool... at the least take it into consideration , thanks for your time...peace

@ScannerDanner 2 года назад

@@HOTRODRICO definitely great feedback and this is something Caleb and I have been actively discussing. Some of these are absolutely necessary to same a TON of time in the final production, but the overuse can be distracting to some. You will see less of what you are describing probably starting in July or August of this year! Others were saying the same. As for the lighting. That is my brothers shop. We are actively looking for an upgraded lighting system for him to help no only him but with our videos. So there is no cinema effect here that we are going for. Just bad lighting. We WILL do better! Really appreciate you and this comment. We will do better! I promise!

@JimmyShagoury 3 года назад

That little dance to the car alarm 😂 Caleb is an artist.

@jamesrezza7854 3 года назад

I worked for Cadillac in the 90s and 2000, that 4.9L is a great motor

@UcantBeSerious03 3 года назад

I'm not even a mechanic anymore, I gave up on that field in early 03. Yet I still enjoy the diagnosis - I worked with so many part changing monkeys

@SuperMarioDiagnostics 2 года назад

High production value, amazing product and systems knowledge, AND the importance of tooling. What more can you ask for? Love this!

@youmeek 3 года назад

Wow! These post editings are awesome! Nice job Caleb! Love it

@ScannerDanner 3 года назад

Glad you like them!

@Paul1958R 3 года назад

Clan Danner: Great video - thank you! Caleb - great camera work Paul - great explanations James - great hair (as always!) God bless Paul (in MA)

@rexreid6915 2 года назад

I love you Danner! You're my repair hero!! If only every city had a dinner like you. I'm rooting for you!!

@DrFillyBlunt 3 года назад

Loved your explanation of why you wanted to see a ramp instead of a straight shot up on the scope. This is the type of education you can't get from parts changers. Love learning details like this. I have a little bit of background knowledge on electrical but know very little about cars. Videos like these help to fill in the gaps so to speak and demonstrate to me how electrical theory is applied in automotive diagnostics.

@faustogonzalez8397 3 года назад

Great Video Paul, I especially like how you and Danner interact, the way you respect each others opinions and solve problems. Keep up the great work !!

@cjayjayjay2973 3 года назад

Great teacher and a great video editor/ videographer. I love learning what you teach

@scope3autos756 3 года назад

This is a great little video. Good refresher regardless of the age of the vehicle. We have had a heat wave over here in the UK and I haven’t touched an engine in about 4 weeks, all my workshop is full of is window regulator issues and door locks with electrical gremlins.

@amirbeganovic3522 3 года назад

Awsome Video! I take my hat off for you guys for being there for us to learn. Thank you! This reminds me of my first shorted injectors problem about 15 years ago. 1994 Chevy Lumina 3.1. It ran great while cold. As it got to operating temperature it would miss under load and longer it ran worse the miss would get. I was convinced that it was the ignition system... We all lost sleep on this one for a few days but eventually got it figured out. 3 out of 6 injectors were shorting out. We ended up swapping out all 6 and never saw the lumina again. Happy diagnosing to all!

@timgebhart8735 3 года назад

Thank you for sharing your knowledge and skill recently had a bunch of codes and truck would not go out of Reduced engine power. Took me a few hours but I found the Green spot tug test and it snapped thank you Danner I was about to give up.Learning is power.God Bless.

@MarioDallaRiva 3 года назад

Video Grand Master Caleb deserves a raise in pay. The edits and overlays adds big time to the educational content. 👍🏻

@ScannerDanner 3 года назад

Great to hear

@simonilett998 3 года назад

Congrats on the 300K subs milestone guys. I like these Sat night/Sunday morning premiers, I get a chance to join in the chat, and watch 'em as soon as they hit YT. Nice one Caleb, I love the flashing lights and Cat/Danner Dance edits at the start..lol🤣👍🇦🇺

@gregoryfairchild2460 3 года назад

Good waveform patterns are priceless

@rickrogers2649 3 года назад

The more things change the more they stay the same. Awesome video. Thanks for all you do and congrats on 300K subs. Well deserved !!

@robertrichardson1133 3 года назад

Great information on waveforms, great video all together. Tell Caleb he is doing a great job editing and adding all the extras!! Thanks for alk you guys do.

@salvadorgutierrezr5914 3 года назад

Thanks for the video Caleb , and thanks for teaching Scanner Danner, and saludos to brother Danner

@PaulysAuto 3 года назад

This is why you're video's are absolute GOLD 💯 Thank you for everything Paul!

@ScannerDanner 3 года назад

Thank you my friend!

@patrickkabunga4526 3 года назад

I salute you SD, your stuff is making me a diagnostician. I request you share more from the premium channel. Am Patrick , a technician from Uganda

@ScannerDanner 3 года назад

I'll give you access for awhile Patrick. Take a screen shot of this conversation and email me at support@scannerdanner.com

@mikeaho4143 3 года назад

Thanks for the vid Paul. It's another reason to get all the info from the customer when diagnosing.

@upkarbath 2 года назад

Video quality is next level Paul. Great work

@abraman5 3 года назад

I see the Nissan 300zx 🤩 I hope you might show it more. I enjoyed watching the road trip you guys took to get it.

@cullenmiller8170 3 года назад

Nice video and the editing keeps getting better and better. I was glad to see the Verus in this video. I just bought a Verus of EBay and can’t wait to get it. I signed up to the premium channel and did watch all the basics and Verus classes so far.

@ScannerDanner 3 года назад

Awesome! Are you Cullen there too? I think we've spoken. But thanks so much either way!

@cullenmiller8170 3 года назад

@@ScannerDanner Yes, same user name

@isalmankhan1 3 года назад

Superb, Love it Thanks for sharing SD👍, the intro was Awesome, great work Caleb👍 Love the discussion between James Danner & SD, you guy's are Awesome😎 Special thanks to James Danner & Caleb👍 Stay Safe Guy's❤

@ttstang43 3 года назад

man this helps out so much, learning and understand what and how to look at the waveforms is impressive.. i have the pico 4425A standard kit and i love it.. just wanting to use it more and learn more... I seriously need to order scanner danners book !

@ScannerDanner 3 года назад

Thanks Brad! Come sit in on a few classes first. You'll be able to see what is in the book as I'm teaching through it. This way you won't spend a dime unless you're sure. There is a 14 day free trial, just be sure to cancel before the trial is up so you're not charged www.scannerdanner.com/join-scannerdanner-premium.html Hope to see you there. Start in my Chapter 1 playlist

@Hndsomehubby 3 года назад

The editing is on point nice work Caleb

@zaytoony 3 года назад

awesome intro and beat! great content as always!

@robertmoura7546 3 года назад

Mr. Danner , back in the late 70's early 80's Cadillac made I believe it was a Fleetwood with a 500 c.i with rocker arms actuated by electric solenoids where depending on the speed it would work on 4 or 6 or 8 cylinders, boy that was some challenge back then, great video thanks that brought me back to 3rd year apprentice days

@LowEnd31st 8 месяцев назад

That was a 368 8-6-4 early 80s

@moreykowalenko583 2 года назад

Dan the scanner man, love your videos and the many things i've learned from many a watch.

@htownblue11 3 года назад

Caleb’s thumbnails are getting better and better. Nothing like giving your pops a hard time over anything you can…..hahaha. Good to see an older ride in the mix. Caddy service CCR is Comp CONTROLLED Ride……when it works it’s awesome…..when it works….

@ScannerDanner 3 года назад

When it worked 🤣 good info thanks! I'll be sure Caleb see this too

@tracydiller9378 3 года назад

Great video guys as always and by the way,have not herd that ccr(Computer Controlled Ride) code in a long,long time goes to show how old i am LOL.Have a Great week everyone.

@bigdaddymak1439 3 года назад

Awesome intro Caleb! Even better when Paul gets frustrated 🤣🤣🤣

@herrkiwi3110 3 года назад

Excellent content as always Sir , thank you so much !

@speedy_pit_stop 3 года назад

They got you the wrong wire a couple times, but that didn't confuse you one bit. Thanks for sharing.

@stationaryenginesworldwide 3 года назад

Awesome video Paul and Caleb thank you …now I gotta go back to reading your Book …great information here Paul !

@ScannerDanner 3 года назад

Thank you so much!

@markferraro5250 3 года назад

good seeing you SD great intuation scope work thanks

@billrimmer5596 3 года назад

Great vid! Love it when u use the Snap On. Great that it doesn’t need an attenuator.

@baykarracko1505 3 года назад

Man, I gotta say, whoever is doing these video edits (guessing kaleb) is a genius pro editor, that intro feels like it's from a high end movie !

@spelunkerd 3 года назад

Caleb is a creative genius.

@throttlebottle5906 3 года назад

most of them I replaced shorted injectors on, were all shortly after a water pump failure/coolant leak and running hot, not enough to blow head gaskets/warp heads, but they always killed the middle fuel injectors, then they'd run a bit rough until overheating the ECM drivers and die until cooled off. the first time I ran into that, I nearly replaced the ECM thinking it was bad! almost a parts cannon fail, except I recalled an older TBI, injector coil going bad and killing ecm, which I did replace without checking injector. fortunately back then it was easy as junkyard pulling one and chip swapping. I lost a whole $40 I think lol

@kirkabrahamson1148 3 года назад

Awesome video again Danners. The style of videos has changed but the educational content stays the same.....Its always been great. The family interaction is great but also the "real world" diagnosing. Mistakes get made and things don't always go to plan and showing that in your videos is one of the things that make them great, plus it gives Caleb some great content to get creative lol.

@ScannerDanner 3 года назад

This comment really means a lot. Thank you! And I know you've been with me a long time, so you would know for sure.

@camarobossman 3 года назад

Laugh out loud Amateur hour. Caleb is killing it with the editing. The thumbnail is hilarious you guys are awesome absolutely love the shop and it's so good to see a Cadillac on the channel. My grandfather used to have one of these Cadillacs, as a little boy I would set this alarm off all the time. Now I know why.... it was never my fault it was the car's fault laugh out loud!!!!! AWESOME INSTRUCTION!!!!!!! YOUR older brother is Hilarious i love it.

@ScannerDanner 3 года назад

Thanks so much Scott. Having an interaction with my son and my brother on camera has really changed they way my videos flow. Then of course my son Caleb is the master in editing these days :-) So glad you approve. Some people miss my old videos but whatever, I love being with my family and it just comes out naturally in the videos these days

@manuellamas4747 3 года назад

Great video. Thanks for sharing

@pedromartinez7779 3 года назад

Great content ! Wish you were located in Texas.😁 I'm learning alot from your videos . I appreciate you for educating us .

@shamessun 3 года назад

Thank you man and for your brother and son

@LynxStarAuto Год назад

Brought back memories. I had one of these for a bit fresh out of high school. I remember having to put fuel injectors in it. Did all 8 myself. Btw CCR is the electronic suspension. Probably has bad drivers on the struts.

@curiosity2314 3 года назад

Good work on this unit. Good humor and a great attitude towards this industry and I'm sure your students at college. I still would have liked all 8 the same but what can you do. Interesting to see the differences on the scope.

@joseduranjr3152 3 года назад

I’ve always wanted a Cadillac like that

@gregjones8501 3 года назад

I was about to say I don’t know wassup with these failing injectors here lately. I just had a Honda Accord today that absolutely mopped the floor with me. ( I really wasnt expecting a bad injector to be honest) Great video Danner! I didn’t understand the ground stacking portion too much ( it was a quick shot so I missed what you were doing)

@ScannerDanner 3 года назад

the extra ground lead on the yellow channel, it is meant to hang and that is where your other channels ground to, NOT the scope. Make sense? Nice to hear from you too my friend! It's been awhile. Hope you and your family are well. God bless

@Russell_Duncan 3 года назад

Enjoyed that guys. Nice to see Tommy popping up in the chat. We miss your videos Tommy.

@ScannerDanner 3 года назад

we're bring some of Tommy's stuff to premium, he is awesome for sure, thank you my friend

@Russell_Duncan 3 года назад

I’m sure you’re proud to have been a part of Tommy’s development history. Look forward to seeing the videos on Premium.

@mannyautotech 2 года назад

very good lession like always, thanks for sharing

@mike-yp1uk 3 месяца назад

Another great video. Thanks

@medch4193 3 года назад

congratulations for 300k subscribers

@jkkennedy8919 3 года назад

This is a bad man at his game 💯🔥

@martyb4815 3 года назад

Awesome info. Now only if I had the equipment to do it. Lol I could test my 2011 5.3l GMC for all my missing problems. I know my aftermarket coil packs go bad, but still have bad mpg on highway.

@snooketcher 2 года назад

Man have I done a bunch of those injectors! It’s getting challenging to find a good set now, all the brands that make replacements nowadays are pretty much a time bomb waiting to happen!

@jkkennedy8919 3 года назад

This Man is the best teacher awesome

@thomasdemarco617 3 года назад

nice Dan great book I love it

@mobileautoserviceanddiagno2997 3 года назад

Tanks for everything very good diagnostic

@davakil 3 года назад

Your the man Paul 👍

@PistonShack 3 года назад

I would like to see more 1980-1990 epic cars diag on the channel. I am working on 1988 Mazda b2000 truck and i like simplicity of it. Thanks Paul.

@TheCarTakerGarage 3 года назад

OOOHHHHHH Congratulations on 300 K Subs!!!!And also..thank you for awesome video,and the alarmgoingoff section editing...hahah that cracked me up.You are the EditMan, Caleb :) One thing...how would the resistance in these injectors that are failing look like? would they be within spec , internal resistance wise? Greetings from theNorwegianViking,Stefan :)

@ScannerDanner 3 года назад

They will drop in resistance as they fail. 12.6 ohms is the spec. That one that was near 10 amps would have measured around 1-2 ohms. But sometimes these would only fail when they got hot, so measuring resistance can look near normal when they are cold. Also the current flow acts as the heat im talking about too. It stresses the windings where an ohmmeter does not. But you should be able to catch most with just an ohmmeter

@Pablo_Automotive 3 года назад

Thanks a lot for another interesting video

@M-diag-auto Год назад

Thank you mr danner

@65blablabla 3 года назад

OMG that was funny the horn......you guys made my day....

@alb12345672 3 года назад

THis is stuff you learn in Electrical Engineering.

@charlesmecum5009 3 года назад

Wld love to buy that car gorgeous, older cars hv so much more curb appeal

@jakejones2482 3 года назад

Love these caddy's

@autoscan7otto489 3 года назад

Thanks Dan keep going

@godfamilycountry4211 3 года назад

Wow. You are gifted and sharp as a tack. Love the lesson. Greek but I follow you. Is a 1998 Northstar known for injector shorts??? Thx

@ScannerDanner 3 года назад

Thank you my friend. No the 98 would have multec-2 injectors, the multec-1 was known for shorting, the multec-2 is known for sticking closed lol

@georgebonney90 3 года назад

Thank u mr danner 👍

@markhollins2190 3 года назад

Great Job

@azekanarine6227 3 года назад

Great video once again.. can you advise me on a scan tool to purchase to use in my country, I work on alot of nissan vehicles,Toyota, etc.. i'm from guyana ,South America.

@JimmyMakingitwork 3 года назад

Proof that the best mechanics are still mechanics!

@MarioDallaRiva 3 года назад

Bravi! 👏🏻👏🏻

@flightmaster178 3 года назад

It seems like injectors are a pretty common issue now on those DeVille’s. I just changed the injectors out on mine. A fun job indeed. Lol Also ironically, I too have an alarm problem. However my security light continuously flashes with doors shut and unlocked and stays solid when doors are locked. Normally it’s supposed to extinguish five seconds after. Also, if you need any reference material I own the entire factory service manual for it. It’s like 4 inches thick.

@bdtews 3 года назад

I've actually dealt with this before, and I found it by ohm ing out the injectors. 2 injectors were hogging all the pulse. No start. BUT it WOULD RUN on carb cleaner. (group fire. 3.1 Chevy Camaro) MTBE in the fuel ruined a TON of GM injectors

@billsmith2212 3 года назад

On my 1987 , 2.8 L , the injectors are buried under the intake plenum . I checked the ohm reading through the harness on each group of three . The actual problem was a sticking EVAP Purge Solenoid . It is pulsed and would stick open . It was intermittent and created a low vacuum condition and loss of power . I plugged the hoses to verify .

@arthurfricchione8119 3 года назад

Very informative video Paul. Thank you for sharing. 😊

@brahimjaponi9982 3 года назад

Thanks poul

@jroman23 3 года назад

Good video! What about if you don’t have a scope to see the waveform. A incandescent test light to backprobe the control wire of a suspected injector is enough to blame a Computer fault?

@pantherplatform 3 года назад

One of my customers has one of these, same color, with a 4.9 V8 and it's had so many issues. It's a rust belt car from da U.P. so it's already had all the fuel lines and brake lines replaced. It hauls ass but it's not as nice as a rear wheel drive Lincoln Town Car.

@ronfraley6417 Год назад

I have a 1990 flertwood with the same issue and now I can go back to the dealer with this info. Seems once the car starts cold it shudders and has a rough idle. Smoothes out after running a while but still not what it should be. I'll be having this looked at. The other thing. When I turn the car on and at the top of the dash it sounds like a clicking noice for a second and a half then goes away.

@dans_Learning_Curve 3 года назад

Like #607 Thanks for the video! Life is a learning curve! HINDSIGHT is 20-15!

@calebldanner 3 года назад

20-15 is right lol

@jesserasso1042 3 года назад

Good looking dodge in the back ground

@johnasosajr 3 года назад

I need a scanner danner hotline number lol good stuff man I’m new to the field mainly oil tire brakes and suspension right now working up to it

@ScannerDanner 3 года назад

Keep watching, ill help you get there 😉 thanks!

@notsureigaf 3 года назад

0:43 this track set my speakers aflame 🔥 where can I cop the full mixtape

@leocheckup6645 3 года назад

Nice work. I am a repairman here in Brazil. On RU-vid we don't have the translation option. Looks like it's measuring current from the Ignition Coil drive. What was the solution in this case, in the end you started looking at the injectors and how many dollars did you charge for this repair?

@powerpower1797 3 года назад

Good video.

@15205golfer 3 года назад

Command Control ride. One of the strut controllers is not responding properly.

@shauno3697 3 года назад

In the dialogue about not hearing an injector vs what was seen on the scope, I was left wondering if Danner wasn't simultaneously dealing with a mechanically stuck injector or two. I've only ever had to diagnose one of those cars. It already had eight remanufactured injectors in it and was missing pintle bumps in the voltage traces on about as many cylinders as what your car was missing on. Does that sound viable?

@ScannerDanner 3 года назад

The multec-2 would mechanically stick. Never saw that on the multec-1 like this caddy had. Plus this one ran pretty good under load, so even the shorted ones where still spraying a bit, at least 7 of them were

@alanw5879 2 года назад

With that 2nd injector, the downward spike after the injector shuts off, its like a negative spike, Ive noticed that on other components before, that are failing and I know they have a flyback diodes for the collapsing magnetic field, but could that negative spike be the diode leaking threw due to the higher current on a shorted component?

@ScannerDanner 2 года назад

Not sure my friend

@markryl-kuchar2373 3 года назад

How bad is it to admit that even though I’ve owned the car for years I still can never find the hood latch on the 1st try

@jeffshadow2407 9 дней назад

Only the 1993 DeVille has the hood release latch under the passenger side grille (1991 to 1993 models).

@oqhr 3 года назад

Hey man. I have 2020 hyundai elantra My car act weird after 15k miles; engine does not run smoothly, transmission is not smooth, idle is not smooth, RPM some times fluctuate at idle and when it runs. I have to clean the throttle and reprogram it every 15k miles, but I don't know why it does like that since the car was new. By the way, I do all maintenance at time. Please give me any solution to solve this problem.

@westonwhitlock7034 3 года назад

16:07. That 86z in the background 👍🏻

@calebldanner 3 года назад

That would be Jake Danners car 😍

@westonwhitlock7034 3 года назад

@@calebldanner nice! I’ve had a few of those z cars over the years. Love the car.. and the content man. I’m a younger Audi tech in the field and I’m learning so much from watching this channel. Everyone looks at me funny when I apply the fundamentals. But my diagnosis are 100 percent. So thank you Caleb, Paul and Danner.

@wrightsrrt871 2 года назад

I would love to take your classes are they online classes or are they near northern CA ? Just getting back into cars use to do more in high-school than went to construction and now just getting back in it again. Switching to michanic work and shutting down my handyman buisness cause my body can't handle construction anymore. I just bought the autel ms906ts scanner and looking into the autel osliscope as well as there 8 mil inspection camer that hooks to scanner. Also curious about if you can show more of the autel device stuff as I like your way of explaining how to diagnose. Thanks for all you do and show us out here as some people like to save money still and fix there own stuff.

@ScannerDanner 2 года назад

Online via my website www.scannerdanner.com/join-scannerdanner-premium.html Thank you! Hope to see you there

@matthewennen9311 2 года назад

I had white 93 deville for 15 years but i had to pay to get that alarm disconected it was like 200 bucks for that but the battery never went bad after that

@thomasdemarco617 3 года назад

change em all hope you can find em