2001 Buick Park Avenue Front Lower Control Arms

Подписаться 14 тыс.

Просмотров 47 тыс.

50% 1

Replacement of worn lower front control arms on a 2001 Buick Park Avenue.
Disclaimer:
Due to factors beyond the control of CharlesAndCars, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. CharlesAndCars assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. CharlesAndCars recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of CharlesAndCars, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not CharlesAndCars.

Авто/Мото

Опубликовано:

24 ноя 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 95

@OscarGomez-oo7im 3 года назад

This model is not exactly my car; but the video has been so clear and so clean that next week my regular cracket - cracket will be eliminated from my Lacrosse... Thank you Charles, you show me that a difficult job can be made easier if you know the right way to handle it...

@hubcap2020 5 лет назад

Excellent Videomanship. Thanks for not making us watch every twist of the wrench and skipping nonrelevant sections..... ! : )

@franciscoperna7963 4 года назад

Awesome video I be duing both of mine on my 2005 buick lesebra today. And because of the detail video you did I be able to due it safely. You just save my family 800 dollars good bless you sir Thanks again.😎 from Louisiana

@CharlesAndCars 4 года назад

glad it helped

@charlesmarcone9210 4 года назад

For 3 years I have had a phantom knock/clunk drivers side. Thought it was CV , THEN STRUT. finally replaced hub and CV AXLE AND IT WAS WORSE THAN EVER. TOMORROW BALL JOINTS AND BUSHING INVESTIGATION, BEEN AT WITS END. AFTER YOUR VIDEO 99% IT IS ONE THE OTHER OR BOTH. LET U KNOW. THANKS A TON ANYHOW. LOVE YOUR VIDEOS. GREAT GREAT HELP.

@KADEBOYXXL 2 года назад

Well done Charles, very strong on the instructions of the hard to view areas. Thorough coverage of each step from removal to reinstall. Comprehensive description of keeping things safe in lifting and loading the vehicle for final torqueing. Gives a very solid feeling to being able to get in there and tackle the monster. Thanks very much for your help.

@CharlesAndCars 2 года назад

Glad it was helpful!

@DrSeuss-qw7cl 5 лет назад

Thanks so much for your very detailed video. I just came from a shop and they wanted over $800 to replace them both, even though only the driver side was cracked. I have a 2011 Buick Regal, but your video is good enough to complete the job. Subscribed!

@matth.4932 4 года назад

A life saver! Great instructions! You the man!

@faridnedj3975 5 лет назад

Thank you !!!!!! You made it a very simple and every details is explaind

@brentmahoney4311 4 года назад

Wow, thanks a lot. I just finished putting it on after viewing this and you saved me a boat load of money. Great video.

@CharlesAndCars 4 года назад

Glad it helped

@madnezznproductions5162 Год назад

Nice I'm bout to do this on my 04 DeVille.. same exact set up

@madnezznproductions5162 Год назад

I really appreciate this video you literally show every thing step by step! Good video 💯

@CharlesAndCars Год назад

Glad it was helpful!

@gerardbyrnes5780 5 лет назад

Thanks! You video helped. I'm not much of a mechanic ..pretty much know just enough to get myself into deep water :), but I had to do this on a 2001 LeSabre (virtually identical) and couldn't afford to take it to the shop. I got through it with a minimum amount of obscenities.

@CharlesAndCars 5 лет назад

Glad it helped you.

@faridnedj3975 5 лет назад

Thank you for this video ....

@curtis88100 2 года назад

Your video is point on good job.i will be watching your videos.

@BodyWeakDotNet 9 месяцев назад

Great video...

@CharlesAndCars 9 месяцев назад

Glad you enjoyed it

@danielworden4695 7 месяцев назад

Thanks for taking the brake assy off so we could see what you where doing.

@CharlesAndCars 7 месяцев назад

No problem 👍

@setag54321 6 лет назад

Charles, excellent video, I've watched two videos of yours thus far, excellent detailed work sir. There isn't enough videos on these Park Avenues on youtube for various fixes of sorts. I've got a 2004 Ultra, that needs the front end tightened up, I hit a elk & luckily didn't total her, it was a close call though. Your time is appreciated & I subbed. Later Brother

@abdulshaheedcrutchfield3315 2 года назад

No such thing as luck

@setag54321 2 года назад

@@abdulshaheedcrutchfield3315 Right, go play the lottery..lol.

@ericjones4368 11 месяцев назад

I have an 2001 oldsmobile aurora 4.0 set up is the same as you just did it helped me change my lower control arms thanks for the tip on putting weight on the suspension then tighten down the bolts cause I would have definitely overlooked that thanks and look like you need a cigarette lol.

@CharlesAndCars 11 месяцев назад

glad it helped

@ruineka_one 6 лет назад

I followed your video on the timing chain replacement on the 2004 Mazda Tribute/Ford Escape and you are a life savor for sure! I just wish you included videos of how to take things apart easily...It is such a pain to work on my 04 Ford Escape, I constantly ran into clearance issues and whatnot throughout the entire process. That being said I love your videos, keep it up!! :)

@CharlesAndCars 6 лет назад

Yeah, sometimes there is no easy way to take things apart. Many cars (especially newer ones) tend to be limited in access space and, in many cases, it's getting to what needs to be fixed/replaced that takes most of the time... not actually fixing/replacing it.

@CharlesAndCars 6 лет назад

That's why you end up with so many tools over time as you add them to deal with specific cases where they just save you enough time to be worth owning...

@HemiChrysler 5 лет назад

I agree with you about not dismantling the steering knuckle/hub. I would only add that the job can be further shortened by not removing the brake caliper and disc.

@CharlesAndCars 5 лет назад

Yep, I just take it apart so it's easier for others to see what's being done.

@ifixeditmyself1926 2 года назад

Very helpful!

@CharlesAndCars 2 года назад

Glad it was helpful!

@CStudyway 6 лет назад

Ive looked for replacement bushings but I havent had any luck other that aftermarket poly bushings which require original bushing dimensions

@Mackandal- 3 года назад

Thank you, Bro!

@CharlesAndCars 3 года назад

No problem

@gordonliddy9418 5 лет назад

debating on doing this to my park avenue... i am going to replace tie rod ends as the steering has play in it. Not sure if some of it is ball joint related as well or not

@backyardbuilttrucks1 5 лет назад

I have always used a torque adapter which like a boxed end wrench for a torque wrench and torque them down . as you said you can add a few pounds to spec to do it without removing strut and axle.

@ryans413 4 года назад

Backyard-Built-Trucks It’s all on feel like the pin should keep the castle nut from backing out so just get it as tight as you can

@tkers7021 2 года назад

I have 04 LeSabre so I'm a big fan. Your wheel bearing vid where you showed hitting the old one with a hammer to get it out saved me about a year ago. Now I did the left control arm , no problem but the right one, Moog by the way, I got the two bolts in loose, but the ball joint is a couple inches off. And the knuckle is dropped down too far. I can jack up the knuckle, but I can't wrestle it over enough. Why is it hanging too low? Then I tried loosening the hub nut, no help. Had to take a break I'm getting wore out trying to change the jack heights. You make it look easy. But the easier it looks, the harder it is!.

@CStudyway 6 лет назад

I enjoy your videos and they have been very helpful with replacements on my 04 DeVille. I have a question for you.Have you had to replace the bushings in your rear control arm?

@CharlesAndCars 6 лет назад

No, haven't had to do that...

@FireSneaks83 2 года назад

An old video, but super helpful. Can an issue with this lower ball joint cause camber alignment issues? I once heard camber = ball joints, toe = tie rods…

@CharlesAndCars 2 года назад

Yes, worn/bad ball joint will affect camber

@DaveyDave1050 2 года назад

I got both control arms AC Delco from Rockauto for $122.

@felipevalles8041 4 года назад

My Lesabre is doing like a clunking Noise and feels like front end shaking when braking at very low speeds I change all mounts but still doing it ,my bushings on this low arms are gone..do you think is the problem? thanks

@CharlesAndCars 4 года назад

If you know hat the bushings are bad that's where you should go next.

@nelljayne6864 2 года назад

Hey I also have park avenue and the bushing on front driver side is bad, do I need to replace the entire arm? Is there a lateral link in front? Also should I replace cv joint axle or wait until I have too because it’s all original suspension and just turned 20 this year and showing signs of needing new air shocks in back and now front driver side bushing

@nelljayne6864 2 года назад

If I could send a picture, it looks like a ball that should be connected to the lateral link? But it’s not connected to anything. Like on back of the arm, there’s a ball at the top and nothing is connected to it, im also leaking coolant from the front driver side near the coolant reservoir , manifold, or radiator. Not sure but it’s not on the side with the pump and pully. And the leak is like under the heat shield way up front, hoping it’s a hose or the radiator. Let me know what you think

@CharlesAndCars 2 года назад

I see replacement bushings for the rear bushing on the front control arm, but I don't see any replacement bushings for the front bushing on the front control arm.

@Brian-fo8sh 7 месяцев назад

Do the sway bar end links need to be under load to tighten? Doing those this week too. Thx.

@CharlesAndCars 7 месяцев назад

@Brian-fo8sh 7 месяцев назад

@@CharlesAndCars thx

@johnwagner4559 4 года назад

Great vid! But I would've replaced the stabilizer pins too while there.

@CharlesAndCars 4 года назад

Yep, it all depends on what kind of shape they're in.

@dennisgraham9444 3 года назад

I'm curious why u put the suspension under load before u tighten everything down. As always , great vid ty for the help on my 2002 park ave.

@CharlesAndCars 3 года назад

Before tightening the bushing bolts you want the suspension at ride height so there bushing is in the proper position before torqueing it down. That ensures that the twist that normally occurs in the bushing isn't more than it should be. If you torque it without it being at ride height (preloaded) then when it is at ride height it already has torque on the bushing that it shouldn't.

@dennisgraham9444 3 года назад

@@CharlesAndCars u the man Charles!!

@widtrak77 5 лет назад

Thanks for the great video and how to do it properly. I know you were removed the caliper for making the video but can you actually do this with the caliper still in Place?

@CharlesAndCars 5 лет назад

Yes, you can.... just makes it harder to see when shooting a video

@widtrak77 5 лет назад

@@CharlesAndCars Thanks, I see now that you said that near the beginning of the video🙄 I missed it. I have a 2000 Ultra I have enjoyed since 2006. The control arms were replaced 6 years ago. The bushings are still good but one of the ball joints went bad. This job seemed intimidating but it really isn't. I will need an axle eventually and that seems more intimidating especially the part about getting it seated back into the transmission. Is it not typical practice to replace those seals when you change the axles?

@CharlesAndCars 5 лет назад

@@widtrak77 I would replace the seals ... really simple and not much cost to the seal... Axles are pretty easy to do on these cars.

@widtrak77 5 лет назад

@@CharlesAndCars Thanks, you don't have a video on that do you? lol

@widtrak77 5 лет назад

@@CharlesAndCars Is this a video? It doesn't link to anything specific. Just my you tube account. Very strange

@johnwagner4559 3 года назад

You didn't need to take the axle nut off? Hell of a job! Thanks! Can control arms cause a front end vibration at highway speeds?

@CharlesAndCars 3 года назад

They can, but there are other things that can cause highway vibrations as well: alignment, unbalanced tire, cv axle, tie rod ends

@williamhayes9642 10 месяцев назад

I went to get an alignment and they said I need to replace my control arms because the bushings are too worn. My tires have been wearing on the inside. I'm hoping this helps .

@CharlesAndCars 10 месяцев назад

Could be control arm or worn ball joint.

@williamhayes9642 10 месяцев назад

I put the new control arms on the front and it actually helped a lot. Now I have to get the back sorted out.

@williamhayes9642 5 месяцев назад

Do you know anyone that sells control arms or bushings for this car?

@stephenlacher587 4 года назад

Looks like you already have a few new components under there.

@CharlesAndCars 4 года назад

Yep, basically everything in the front end was replaced in the car.

@robertcoates6800 4 года назад

Did you have to grease the new ball joint ?

@CharlesAndCars 4 года назад

If the ball joint has a zerk fitting then it should be greased. If it doesn't have a zerk fitting then there's no provision to grease it. Non greasable ball joints already have grease in them from the factory.

@ryans413 4 года назад

Charles And Cars You can pull the boot off the top of the ball joint and add some more grease before installing for the ones that don’t have grease fittings

@drexcote25 4 года назад

So the whole lower control arm came as one whole piece???

@CharlesAndCars 4 года назад

Yes, including ball joint

@ItsaRomethingeveryday 4 года назад

I have one of these cars it's an 03 and right where the control arm connection on the forward part of the subframe the car had been in a collision and the welds on the mount had all split, I had my mechanic weld them for around fifty dollars, he said one good bump or pothole and the car would have been on the ground causing several thousand dollars of damage, glad I spotted it while checking the transmission mounts cuase they ended up being severely worn causing the motor to rock back and forth, liked your vid, Thanks, do you have a Facebook link we can connect with you on, I have an automotive group on their that I'd like to invite you to

@pauladkison1068 2 года назад

B,,

@leonardc2234 5 лет назад

I dont understand why they list torque specs like 41ftlbs plus 120 degrees.. Why not just say 42 or 43ftlbs

@CharlesAndCars 5 лет назад

120 degrees on top of 41lb ft is much more that 42 or 43lb ft.... Sometimes they list it in degrees... sometimes just in lb ft

@dontblameme6328 6 лет назад

You have great videos and you definitely know what your doing but... I cringed every time that car rocked on the stands.

@CharlesAndCars 6 лет назад

Yep, it wasn't going anywhere... had floor jack as well just as extra safety measure...

@ryans413 4 года назад

Don’t need an alignment for replacing lower control arms should be alright. The only time I’d get an alignment would be if you removed the tire rods or struts

@CharlesAndCars 4 года назад

I always get it checked unless I know when the last one was done. If an alignment was done with the bushings worn then putting new control arms can throw it out.