Avalanche 6” Rough Country Lift and Overhaul Part 4 

14:15 he got that lifted drift truck alignment

THANK you so much for explaining in details the trials and tribulations and not trying to sugar coat the hard stuff,I definitely appreciate THAT 💪 I just got the same truck and plan on taking the same journey as you with lifting it and a bunch of other stuff but,I'm not as skilled as id like to be so it should be fun 🤷🏼‍♂️😂

That came out really nice , good job . Looking forward to your next video . Take care .

it looks sweet. the tires and the lift really give it some bad attitude. nice job

Bravo bravo bravo👊!!! Looks awesome! Hard work pays off. Enjoy man enjoy!

Sweet video really informational watched all 5 videos 👍🏻

Looks awesome man, good work

IT LOOKS SO AWESOME!!!!!

Love the video 💪

That's looking amazing. I totally Agree with you when you cleaned and painted everything while you were under there. Try the stuff called "perfect 10" it makes black plastics shine like new.. and if your plastics are faded use a heat gun to get em back to black. 👊

I have a 2008 chevy avalanche wanting to install a 6” lift. Yours looks great.

Damn that thing looks so good!! bet you are glad you finally got it done. now you need a photo shoot and a video of it on a few small trails. Makes me actually like the avalanche.

I was just thinking of getting a Avalanche after I pay off the Tahoe and make it a little project. Keep us posted especially on the tuner.

Did you purchase standard replacement control arms for this or ones that accommodated the lift? I see the caster/camber plates on the upper control arms.

Looks great man. If youre willing to put the time in a heat gun works great on the plastic cladding. Or a fine grit bedline spray

4:38 Just above and left of the torsion bar, those rusty tubes are the fuel lines. I hope those have been replaced or they are surely leaking by now. Those are a GM part and a big job to replace, they route along the frame rail under the ABS module so that has to come out. Then after you get the brake lines hooked back up to the ABS module you will need a Tech2 scanner to run the automated bleed procedure to get the air out of the ABS module or the brake pedal will be forever spongy. I had a guy try with his $10K Snap On scan tool and it could only test run the ABS but could not run the bleed, which is similar to a bench bleed on a master cylinder and requires a person to maintain pedal pressure while it cycles the ABS and pumps fluid to the MC to let the air reach the reservoir. Must have the Tech2 for the automated bleed (I have one). I'd say the torsion bars should be replaced also. Those wear out without looking any different and lose some of their supporting resistance same as the rear coils do. I replaced the entire frame and chassis on my 2002 Avalanche because I too live in the rust belt, and it all rusted away on me. I mean a new replacement part frame from GM and all new suspension components except the steering knuckles which I reused. But I opted for stock, not lifted, because I do not wheel in my Avalanche. And it practically takes dynamite to get the wheel bearing hubs out of the bores in the steering knuckles. Amazingly GM recommends thread locker on the 3 bolts to the hubs. They will get so rusted in tight that you could take all the bolts out and safely drive, I am not joking. I assembled the new ones with serious urethane anti rust coatings, and of course I use anti seize by the tub while others use it by the tube. I literally have tubs with brushes. An excessive amount of anti seize is usually about right.

Hello, how much is the ground clearance of the vehicle after the 6-inch upgrade? (Tire and rim size is?) A video about their height and ground clearance were really great

When you lifted this, how far up did you turn up the keys to get the 6” inch lift?

What’s the rim size and offset? Looks good!

how much time did you spend on the liftkit to get it installed?

I think you mentioned you used wheel spacers in the back to true-up with the front after lift. What size wheel spacers did you end up using in the back? Thanks!

Looks amazing dude. I have the same truck. Year, color etc.

You mentioned spacers, did you have to use wheel spacers to fit 35" tires? If so what size spacers?

Ecm for the tires ???

I needed a new battery in my 2015 Cadillac ATS which is in the trunk. So I was skeptical of me doing it and breaking shit so I called dealer to see how much. It was cheaper installed by dealer than just the price of the battery at advanced Auto! Crazy

Did you have to use spline lugs

How tall is the garage door?

Hey there, did you replace the factory torsion keys with OEM keys, or are they 1-3” keys? ThankYou

What Hanes manual are you using?

Hey bud what size spacers did you use for the rear?

Did you have to crank the keys at all to match the rear?

What wheel and tire size you running

What size tires?

No se entiende el idioma x eso casi no se mira