DR350SE Carburetor Rebuild | The DR350 Lives! | Project Quarantine Ep. 4

Подписаться 70 тыс.

Просмотров 20 тыс.

50% 1

Today I rebuild the carburetor on my Suzuki DR350SE. This was a long process, during which I removed the carb, took out all the old jets and components, cleaned everything, reassembled it, and repeated until I found the problem with the bike. I go through replacing the jets to inspecting the diaphram and slide, and cleaning everything. This carburator is a MIKUNI BST33 carb, which is the CV style. Off road bikes have the TM33 "pumper" carb, also made by MIKUNI. After the first cleaning the bike would idle but not rev without dying. Eventually I traced this problem back to needing to add a spacer to the needle to get more fuel to the bike.
CashedOutCars, Cashed Out Cars, CashedOut Cars For additional content, check out www.cashedoutcars.com!

Авто/Мото

Опубликовано:

21 апр 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@CashedOutCars 4 года назад

It lives! What should the first modification be??

@Hugh-Glass 21 день назад

Thanks for these. Do you still own the dr-350, I hope so because it's even cooler in 2024. I'm hoping you will do a valve clearance video. Anyway, again..I appreciate the knowledge, you are a champion and good instructor

@CashedOutCars 21 день назад

@Hugh-Glass I still have it! If I ever need to do work my valve clearances I’d make a video on it, but right now I’m not sure I will. I appreciate your comment and support!

@gregory9740 2 года назад

LMFAO the most important parts he fast forwards through....Nice

@beauxpruitt3647 2 года назад

Great video

@justwondering3241 2 года назад

How did you know you needed to add a spacer? I’ve never worked on a carb before. Is spacing the needle a common solution or remedy ?

@guyonacub4335 2 года назад

Hi I like the video Could you tell me what model carb was fitted to the bike please, as I think mine is a standard carb but not sure Would the principal be the same for all carbs, and how do I identify which carb I have ( is there a number on the carb ) Keep making the videos Roy

@michaelclarke6383 Год назад

Why did you rebuild it in fast motion. I need to know how you put it all back together 😡

@themightycrfs5491 3 года назад

When you took the needle out, was the clip on it set to a mark on the needle My clip has a load of small washers under it on the needle What hieght should the clip be set at and what number jets are you using 👍

@CashedOutCars 3 года назад

I didn't take note of the jet numbers, but I'm assuming they're stock. I had to move my clip so the needle sat higher to get my bike to run well, which is what the washers are probably for. I ended up spacing mine up a bit extra as well. Good luck!

@HIFRENDITSJAVI 3 месяца назад

how did you figure out that "the needle needed to be spaced up to sit higher in the carburator" ? Great video. Thank you and props!!

@CashedOutCars 2 месяца назад

I thought it needed more fuel, and the needle controls how much fuel does in, higher up = more fuel

@varsity90 3 года назад

Which one of the two jets you took out and said remember which one is bigger was the bigger one!? I had to drill mine out because they were stripped but have no clue which is bigger

@HabassiiPassii 27 дней назад

Did you ever find out? I'm having the exact same problem!!

@skiapacheadaptivesports9849 4 года назад

How’s it still running? I’m having the same issue with mine. After a carb rebuild it dies when I give it throttle. I’m going to try your trick right now and see if it works.

@CashedOutCars 4 года назад

It’s still running really well. Probably could go a bit richer just to be safe, but I’m not worried about it right now. Did yours die before the carb rebuild when you gave it throttle?

@skiapacheadaptivesports9849 4 года назад

CashedOutCars No before the carb rebuild it would just need to run on choke like the pilot jet was clogged and it would leak fuel so I decided to rebuild the carb did the rebuild kit put it back together it idols great but as soon as you hit the throttle it dies I adjusted the needle and no change

@CashedOutCars 4 года назад

Well, that certainly sounds similar to my problem. Give this a shot and see how it goes. Did you swap any other jets?

@stekwack 4 года назад

am having the same issue something I have found on my carb is a air leak on the throttle spindle, with engine running and before it gets too hot spray some easy start around the carb at mounting to head , and around different parts of the carb I found with mine if I sprayed it on the spindle for throttle on R/H side the engine would rev up, so its drawing air in creating a weak mixture.

@luukinen97 11 месяцев назад

hello, what could be the Suzuki dr when you start it and press the gas it shuts off just like this bike of yours? with the suction on, it's possible to touch the gas. I've disassembled the car many times and I can't find the fault where?

@skualpascal6684 11 месяцев назад

idle circuit maybe quite OK with its air /fuel ajustement, but be sure to well tune up the fuel screw (from full closed position, unscrew of 1 to 1 & 1/2 turn). with rather stable idle, you maybe got a bad tuning & /or too big difference with air/fuel ratio of the next circuit : the one that operates JUST when you begin to open throttle : that have to do with needle (position / shape/ is it worn?), plus its emulsion tube (worn ?) & then with the main jet diameter (this last one is more important for 3/4 to full throttle, but it plays a role almost all along the opening of the throttle)

@themightycrfs5491 3 года назад

Where did you get your carb kit from please

@CashedOutCars 3 года назад

amzn.to/2wCCTG3 this is it, it's a cheap kit but it worked decent for me

@mawirewillard 3 года назад

Any pointers to where i can buy a carb rebuild kit that you can recommend

@CashedOutCars 3 года назад

Yes it’s linked in the description of the video, here’s the link too! amzn.to/2wCCTG3 note that this is a lower end kit but the parts I used worked great for my rebuild

@mawirewillard 3 года назад

@@CashedOutCars Thanks buddy

@Scott-ly3ch 3 года назад

Oh man, I'm running into the same problem. Hope your bikes still kicking! Do you know of an updated kit that would work as yours? Busted link :(

@John-bx8iz 4 года назад

Me again ;) your problems with the carb might be the "cheap" carb rebuilt kit. I had a similar one too and the went with a very high quality one and that made a huge difference. But as I said, id rather spend more money on a TM33 carb. TM36 doesnt make that much sense without porting head, bigger bore etc.

@CashedOutCars 4 года назад

I ended up changing the jets back to mostly stock ones, except for the idle and just using the rebuild kit for seals, I agree, most things in the kit may not have been perfect. For a cheap fix to get it running though, I’ll take it!

@stekwack 4 года назад

am having a issue with my dr350 at the minute after rebuilding the carb with a cheap ebay kit, struggles trying to rev off tick over, seems to bog down pops and bangs seems to be too lean, have tried swapping back my pilot jet back to standard cant swap my emulsion tube back as the threads are damage, it was quite gummed up and didn't want to come out. I'm going to try a all balls jet kit next I think to see if that helps.