Frigidaire Electric Laundry Center Dryer Drum Bearing Replacement (131777700)

Подписаться 611 тыс.

Просмотров 31 тыс.

50% 1

Buy part 131777700 now: www.repairclinic.com/PartDeta...
video provides step-by-step repair instructions for replacing the dryer drum bearing on a Frigidaire electric washer/dryer laundry center (model FFLE3900UW1). The most common reason for replacing this part is if the dryer drum will not spin properly, or if the dryer is noisy.
Learn how to troubleshoot your washer/dryer combo:
www.repairclinic.com/Shop-For...
This replacement video is applicable to the following brands:
Frigidaire
Connect With Us!
plus.google.com/+repairclinic
/ repairclinic
/ repairclinic
/ repairclinic
Join our VIP email list for discounts and money-saving tips: tinyurl.com/pnnh3be
Don't forget to like and comment on this video and subscribe to our channel!

Хобби

Опубликовано:

22 окт 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@ejej6934 2 года назад

Good video. When I replaced the bearing on my older model stackable dryer I was amazed how much lint was packed in the interior of the housing, especially at the rear. The heating elements were covered with lint and I'm kind of surprised the thing never caught fire. I cleaned the interior thoroughly and was amazed how much more efficiently the dryer dried clothes afterward.

@johncasor9698 Год назад

every year you must remove the dryer drum and vacuum out the unit and also the vent ducting so it will work better and not catch fire believe me...

@terrydavis7829 Год назад

What causes oil to be inside the agitator and tub of my Frigidaire stacked washing machine ? I was told that it is probably the transmission, but that it could be a couple of different things, your opinion please ?

@chrissyfreitas8865 2 года назад

I can’t find a drum stop. Do you have part number? It’s missing off my dryer

@johncasor9698 Год назад

you do not need a drum stop...

@DanWebster 2 года назад

why didnt yall show how to replace the entire kit ?

@arnoldrasmussen1676 Год назад

Do u have the barring for this videos part number?

@Jessica-kw8ig 2 года назад

Is this repair for when there is a high pitched constant squeak?

@johncasor9698 Год назад

the noise you here is a worn out bearing holder worn down to the point it is rubbing on the steel retainer so if is that bad this video is worthless because it is not showing the other half of the job which is to replace the drum bearing holder which is what should of been filmed ...

@superGJ24 3 года назад

What do you do if the old bearing was not connected?

@itspaulyall_ 3 года назад

Best comment ever. No one on the internet explains this.

@suzanvoga-duffee2764 2 года назад

"Threading the new bearing before installation might take some effort" Um, it takes tremendous effort. Been trying as hard as I can and still barely made any headway. This is cruel.

@johncasor9698 Год назад

i never ever pre thread that bearing what a waste of time... such a joke to even try...

@Jessica-kw8ig 2 года назад

Whats the average cost to get this done? I don't think I can do all that. Taking it apart seems easy its putting it back is the problem.

@johncasor9698 Год назад

it is a very easy job if you remove the door makes it simple to do. the cost is around $350 and you can do it in 30 mins. and cost around $35

@Dealwithit96 8 месяцев назад

I just relaxed the same thing but the drum seems to hang. Am I missing something?

@hunternewmiller.450 2 месяца назад

Having this same issue. Any advice?

@christinakyburz2959 2 года назад

My dryer is missing the drum stop and I can’t find the part number. It’s not included in any kits. It’s also not listed for sale. Please help!!!

@christinakyburz2959 2 года назад

I’ve done that. I haven’t found the part on any major online store or repair site. The diagram doesn’t even have that piece listed. I cannot find a part number. I’ve called the manufacturer and they did not a knowledge that part’s existence.

@chrissyfreitas8865 2 года назад

@@christinakyburz2959 I’m looking for one to! Did you have any luck?

@dennisgraves9343 2 года назад

I’ve taken apart several stackable dryer units and none have had a drum stop to begin with.

@johncasor9698 Год назад

i have seen many of missing drum stops. worthless they are...

@johncasor9698 Год назад

@@dennisgraves9343 i have seen many missing and maybe like 30 in the past 9 years... drum stops do nothing but slow me down there a waste of time...

@Sny734 3 года назад

After watching 15 videos I have my doubts that anything was needed except a cleaning and new grease. There's no way the ball bearing chewed a hole in the end of the ball. I think it was just a design/engineering difference in the way it was made. The only thing the bearing does is ground the drum for static electric and wouldn't make a squealing noise. I stuck my head inside and can see through the holes at the back of the drum and see the shiny ball. If my wife won't let me disassemble to clean and grease with out new parts on the kitchen table then I think I can stick a curved tube through one of the holes in drum where I can see the ball to oil it or even put some white lithium grease in it to lube the bearing. I've thought about drilling a hole to run a long Q tip with grease to it. Can anyone here tell me that theirs was not salvageable with cleaning and grease or did you just go ahead and change it because you had the new parts?

@kelleyseaton7162 3 года назад

Mine was squeaking for a while and then finally stopped turning all together. I took it apart to find that the entire ball on the beating was completely gone. I had continue to run it so long with the ‘squeak’ that as the ball wore away it also ‘chewed’ away at the plastic seat. I had to replace the whole thing. If yours is just starting to squeak, I’d take it apart now and lube it before the bearing and seat are completely ruined and have to be replaced(assuming that’s the origin of your squeak. There are other places that it can squeak from including the belt arm.). I wished I had. Changing it all was not fun by myself😂

@Sny734 3 года назад

@@kelleyseaton7162 Mine is still running just fine since I lubed it like I told everyone how. Yes it's on my list to tear it apart and clean and lube with clean grease. It's just not on the top of my list any more. Even a catastrophic failure doesn't cost any more. It just means you'll be going to your mothers till the parts come in. You need to see your mother anyway. If I take one day I can clean and re-lube everything and see if it'll out last me or order parts. I have cancer so I'll probably do nothing till total failure. A dry squeak is bad and chewing away at the ball. Dirty grease is bad but will last a long time.

@Sny734 3 года назад

@@kelleyseaton7162 Okay so it was another post I described how I lubes the bearing in 5 minutes. I had a sturdy laundry table right there so up on the table on my knees in to the drum supporting my self with my left arm, a little LED pocket light my face against the grill of holes in the back and I could clearly see the bearing to stick a straw on a can of white lithium grease through a hole and WA LA! no more squeak.

@annamcpherson1306 Год назад

🤯

@johncasor9698 Год назад

i do not understand this video ??? why would anyone ever replace the drum basket bearing ??? and not the holding retainer??? over time the plastic bearing holder needs to be replace i get that but never seen just changing out the drum bearing without the main problem is the plastic holder and i have done well over 300 of these... and take off the door it will make this job so much easier believe me...