No video :(

How To: Bleed a Hydraulic Throwout Bearing - Mantic Clutch USA

Подписаться 660

Просмотров 81 тыс.

50% 1

This is the best way to bleed the T/O bearing. We receive many phone calls on how to properly bleed the hydraulic bearing, so here is our tech video. The sprung type OE style hydraulic bearing in the video is the same style used in our Ford Mustang and Dodge clutch upgrade kits.
The "Urban Legend" is to pump the pedal 1 million times to let the air out, this simply is not the case. We suggest bleediing the slave cylinder while on the bench before the installation on the vehicle. The bearing must be bleed for the system to work correctly.
Tech Tip: Use a short length of rubber hose and small cup of fluid to remove air from the throwout bearing (watch the video).
Be sure to watch our other clutch bearing video explaining "All about Air-Gap" here • Hyrdraulic Throwout Be...
Visit our Website:
manticclutchus...
Facebook:
/ manticclutchusa
Instagram:
/ manticclutchusa
Twitter:
ma...
"In Clutch We Trust"

Опубликовано:

26 апр 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 32

@alexcastillo8983 3 месяца назад

I should had watched this video before all those videos! Very simple!

@davidbuchanan3374 5 лет назад

Best and most detailed video yet. Just replaced my concentric slave bearing on my seat Alhambra and taking these steps first made the job bleeding the system so much easier.. brilliant upload thank you for sharing..👍🍀😁

@thewrx2600 9 месяцев назад

love the whiz quiz cup for demo purposes, haha.

@superpont Год назад

I feel like someone owes me money for watching that.

@narc46 Год назад

Why would you leave the cylinder with the bearing facing up like that and the line at the bottom? Air bubbles go up not down. That method looks like it would be great at trapping a lot of air.

@patriciascoggins1157 2 года назад

We're trying to bleed a hydraulic clutch on a 1991 Cheverly gmc

@justadude8659 5 лет назад

While your video quality and presentation is overall excellent (better than I could do), I don't see how this is applicable to an actual installation. Once you install the bearing, you have no way to press/release the bearing because it is inside the bell housing. If I were to do this prior to installation, I would have to plug the oil line with something to keep the (supposedly air free) oil from running out. Then somehow magically connect the oil line (from the master cylinder) without introducing any air. I think I'm going to try the vacuum method.

@GlorifyGodInEverything 3 года назад

i think this is more of a prep video when you are installing the slave/throwout bearing so you don't run into the issue.

@ballstoyou33 3 года назад

Lolllll me rn I literally just put the trans bakc in I do not want to take it out

@Schnippen_Schnappen1 Год назад

Just cut a big window on your bell housing. Easy Peasy! But srsly these new designs are fucktarded i’d love to meet the engineering coming up with this stuff and beat them to death

@gearymiller7615 11 месяцев назад

@@ballstoyou33same situation. What did you end up doing?

@keithcoffman8395 2 месяца назад

Actually if you push the inner part of the slave forward with 10lbs of air. You pull the line off fill with brake fluid re attach the line ..when you install a bit of fluid will drain out..no air in line reconnect with main line ..works.fine

@kennethalbert4653 3 года назад

Is that a urine specimen cup he's using...LOL

@piss_pisstofferson 3 года назад

You see it too lol 😅

@abdulmoez1272 2 года назад

Wish my mechanic did that

@bobl78 4 года назад

once it is installed in the car, how can you Change the fluid in it?

@MailboxReviews 2 года назад

You bleed it; thats how untill fluid runs clean from bleeder valve (while keeping clutch master cylinder filled so it doesn't suck air

@traceybaker9910 4 года назад

What is that spacer? We installed a new flywheel that was thinner than the silly dual plate flywheel. We need a spacer. We have ruined 2 throwout bearings because it extends too far and falls apart. Does anyone have a solution that you can do without having to buy a new thicker flywheel. ??? Thanks for reading

@keithcoffman8395 2 месяца назад

If your flywheel is 15/16 " to 1" thick A.750 spacer is fine behind the slave drive...especially 2012 later mustang mt82 transmission...

@NunYaBeezWax80 2 года назад

Is your clutch very soft after doing replacing the clutch and slave cylinder. I got mine back from the mechanic and it feels like i am stepping on marshmallows

@JJ-zm7kj Год назад

What car and what clutch did you change?

@okccitizen4400 5 месяцев назад

Pump air out

@michaelkennedy2528 5 лет назад

I have this on my Mustang. I cannot see how what you are doing gets the air bubble out. The air bubble is up at the top, next to the bearing, when you push it down, the air bubble remains at the top. Now, if you turned it upside down, and made appropriate hose length changes, and cycled it like you did before, then I can see where this would be effective.

@codycombs88 4 года назад

Didn't work

@michaelkennedy2528 4 года назад

@@codycombs88 I'll be putting mine back together in the coming days, I have a method that works perfect, crazy easy and is done with everything installed in the car. In fact, the method I use pumps the cylinder up super quick and all you have to do is hook up the hose and can literally drive away. These cylinder s are crazy the way they are designed. I will make a video of how I do it and shoot you a link for future reference. Stay safe, peace.

@dshook1989 4 года назад

Michael Kennedy do this yet? Lol

@michaelkennedy2528 4 года назад

@@dshook1989 yes, I will show you how I did it. I have my car on theroadand it literally tokk 5 minutes to do it. I'll make a quik video and put it unedited on my channel. I am not home withediting software but the point will get across.

@michaelkennedy2528 4 года назад

@@dshook1989 made the video, it is uploading right now. Be kind and let me know what ya think. Sub and like if ya would, let me know if there is anything else you would like to see from my build. I put the dyno number in the video with the dyno sheet in thevideo. Have a few videos of my car on the dyno also, loud as hell, so if Ipost them, turn the volume all the way up so you can get the full effect lol

@jesshowe4591 4 года назад

Allow a good demonstration you can't actually get all the air out like that because there will always be air at the top so you would need to put it on its side like it would be in a vehicle with a pipe of the top so that the air can leave.