How To Cut Crown Molding For Beginners - Outside Corner

Подписаться 42 тыс.

Просмотров 73 тыс.

50% 1

How To Cut Crown Molding For Beginners - Outside Corner
This video shows how to cut crown molding outside corners. If you would like to see my older video on how to cut crown molding inside corner, check it out here;
• How To Cut Crown Moldi...
Check out Scott & his Crown Stop Fence @
WWW.CROWNSTOPFENCE.NET
I hope you guys enjoy this quick video on crown molding for beginners. This trick usually only works for perfectly straight corners. You will have to get more advanced when doing crown in an old home and coping the crown will have to be done. How to cut crown molding isn't rocket science, you just need to practice over time. I do it very little! I'm not an expert in the slightest!
On the hunt for a new miter saw? Here are my recommendations!
Bosch 12" Dual-Bevel Sliding Miter Saw - Corded
geni.us/wxwHPK
Ridgid 12" Dual-Bevel Sliding Miter Saw - Corded
geni.us/UBBW
DeWalt 10" Single-Bevel Compound Miter Saw - Corded
geni.us/VoKmtB
Milwaukee 10" Dual-Bevel Sliding Miter Saw - M18
geni.us/o1xrwZ
How to cut crown molding-outside corners!

Опубликовано:

13 ноя 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 35

@HalfPro Год назад

What I like about is that your video is practical with lots of helpful tips for DYI and NO Pro bragging or living critical info out. Thank you and you saved me from DYI troubles.

@josephgreer9693 8 месяцев назад

This is called keeping it simple great tutorial, caulk makes a carpenter what he isn't. 😂😂 good job

@shilohglasgow2343 Год назад

😮 I learned something new today. I always wanted how to make these

@gaquinn Год назад

This is how I like to be taught to do things I never done before. Thank you so much.

@gaquinn Год назад

Taught to do things

@theobjectiveperspective8300 Год назад

Getting ready to do crown molding in my bathroom remodel tomorrow. Been dreading it, and even thought about getting corner blocks, but I think I'm going to go ahead and give it a shot after watching your videos on inside and outside corners. I think I can do this!

@cendygorman1911 10 месяцев назад

Love it!!! best tutorial ever!! thank you so much... everyone make it look so difficult, this change everything!

@TheDurbinCompound 10 месяцев назад

Funny how some people still don’t get it and say my video sucks 😂🤣😂

@raulledesma382 4 месяца назад

Great video!! Thank you!!

@CookingwithMrCooper 11 месяцев назад

Great video definitely needed.

@dj_shellboss Месяц назад

Thanks for this bro 🙏🏾

@adamlink7779 Год назад

Great video.

@ZXman2008 6 месяцев назад

Super helpful. Gracias

@1DIZZASTER Год назад

Awesome !

@SuperDavidBrothers Год назад

This is very cool I didn't know how to cut crowns like this for both cabinets and kitchen counters for sure this is pretty dope!! When you're measuring with a tape measure, how do you measure the length of a piece of wood even though you're making a miter cut with a 45° cut?? If you measure that wood on the angle of the wood, it's going to look off so would you measure the wood at the top then or should we just measure our length of our cuts on both the kitchen counters and cabinets (because like you said, those methods might be more accurate vs cutting on the top of the wood)?

@donwebb7438 4 месяца назад

I missed on setting up the saw. Is it a double bevel or a single bevel by swinging the cut left or right and not tilt the head.

@marcosmunoz1663 3 месяца назад

Thank

@user-lp2ob7un2r 9 месяцев назад

my two pieces join at a 45 degree angle vs the typical 90 degree angle. Do I follow the same process on your video

@TheDurbinCompound 9 месяцев назад

Yes, but the angle would then be 22.5 degrees cut

@Viuserlv4qp 8 месяцев назад

Good boy

@1DIZZASTER Год назад

I wish I would have not been so pig headed and watched this video before I ruined some very expensive crown molding .

@TheDurbinCompound Год назад

It happens! I had to learn at some point too and I’ll admit I probably suck pretty bad compared to some finished carpenters.

@mikemaid5350 Год назад

Don't forget the silicone grease!😀

@TheDurbinCompound Год назад

👋🏻

@mikemaid5350 Год назад

@@TheDurbinCompound Started watching your channel.

@dawnkobylarz7126 Год назад

@@TheDurbinCompound I got me a pair of the Rock Rooster AV 611 6" boots man!for a $125 bucks,I didn't even rush delivery and got them in 2 days,I live about 50 miles from the Kittery,Maine trading post ,they have a large variety of outdoor/indoor wear for working,hiking,etc....,these boots are as comfortable and nice as any 250 to 300 dollar boot in that place, Chippewas, Survivors, Wolverine etc...,thank you for your tips,and all you do for your fellow Dudes!You seem to be a good human!Not that many left,or maybe their hiding!Hey, Slow Down on those Chop Saw cuts!!!!!!!

@grimsnig Год назад

why do you have to always cut upside down? And if you cut the 45 and try to match it up to a 90, in order to perfectly match the corners the crown has one side that drops at the backend in order the match the mitered cuts...what am I doing wrong?????

@djblock215 Год назад

Because you can't hold it in the right place if you cut it without being upside down or flat. You're either not placing the bottom of the crown w the correct spring angle or the angle isn't 90°.. Are you cutting for a cabinet or on a wall?

@johnhavranek441 Год назад

Not always, sometimes the angle won’t permit you to cut it upside down

@johnnywishbone932 10 месяцев назад

If you are from Canada 🇨🇦 can you still be a Finnish 🇫🇮 carpenter? Sorry… Dad jokes….

@jmw402 5 месяцев назад

terrible

@RT-me3wn Год назад

Constructive criticism. You skip around and don't explain many steps or the reasoning behind it. You tilt your molding at an angle against the stop without saying why, for example.