How to Replace Camshaft Position Sensor 00-06 Chevy Suburban 1500

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,4 млн

Просмотров 513 тыс.

50% 1

Buy Now!
New Camshaft Position Sensor from 1AAuto.com 1aau.to/ia/1ACPS00040
In this video, 1A Auto shows you how to repair, install, fix, change or replace a broken, worn out, or damaged camshaft position sensor. This video is applicable to the 00, 01, 02, 03, 04, 05, 06 Chevy Suburban, or Silverado pickup truck.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oai5/1AXAA00013
• 10mm Socket 1aau.to/oWN/1AXAA00017
• 8mm Socket 1aau.to/oWN/1AXAA00017
• Fuel Line Disconnect Tool 1aau.to/oj/1AXAA00041
• Ratchet 1aau.to/oakn/1AXAA00016
• Socket Extensions 1aau.to/o5D/1AXAA00015
• Torque Wrench 1aau.to/ovy/1AXAA00044
• Rust Penetrant
For More Info visit us at 1aau.to/h/bhG/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

16 июн 2014

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 93

@1AAuto 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@northernredneck3896 4 года назад

You did a lot of work. There is no need to go through this much trouble. You can reach the sensor without going through all of that. 🙃

@justchillin9763 3 года назад

How???

@jghqaltga5926 3 года назад

Just replaced mine on my 6.0L. Only thing I removed was beauty cover. Then you're able to reach behind and take it off with socket and pull it up. Takes maybe 30 minutes, don't have to replace manifold gasket (because you didn't remove), and only hard part is feeling for the actual sensor. I used scope for cylinders to help along with face timing my buddies phone and using mine (better quality) as a scope.

@aaronarjes9086 3 года назад

I recommend that you replace the Oil sensor, and the Knock sensors. Looks like the knock sensors have already been replaced on this one as I see atv gasket maker preventing water getting back into the back one. I normally put a bead around both in such way that any water goes around these senors. Oil senor is famous for going out on these motors.

@tjdinfl 10 лет назад

Thank you for these videos! P.S. Don needs an air ratchet.

@1AAuto 10 лет назад

Thank you for watching! 888-844-3393

@AZJDFAN 8 лет назад

There is no need to remove the manifold to replace the CMP on a 6.0. It's tricky but I just did one. Took about 30 min.

@protorch7471 7 лет назад

Tom Fleetwood how did you don't it? I have to do one on my 6.0 in my 3500. Any advice would be great.

@tomjoad1363 7 лет назад

Can you explain how you did it ?

@mariaigonzalez3039 6 лет назад

Nice

@leonardoceja1993 6 лет назад

How?

@dotadodahi3365 5 лет назад

Tom Fleetwood you are absolutely right I just did my Silverado 4.8 little tight on space but got it dialed in 👍👌

@chrisperry3899 2 месяца назад

Great video. I opened a can of worms when i got my manifold off of my 03 Silverado 5.3L

@alanhuggard4724 9 месяцев назад

This is a great video thank you for making it.

@ricardochampion6212 5 лет назад

Is it the same for a 99 suburban 5.7 or is there a video for that vehicle ?

@nha2448 2 года назад

Thank you so much

@only1qu386 3 года назад

@ 8:24 he is installing a different intake manifold. The use of new gaskets is highly suggested with the OE manifold. The "Dorman style" manifold being put back on in this video comes with preinstalled gaskets around each port. It is also slightly taller than the OE manifold . Also, the map sensor gets relocated on that one. It is on the top of the OE manifold, but goes in the lower rear of the "Dorman style".

@1AAuto 3 года назад

+Qu Thanks for the feedback!

@Gt.b8a4 3 года назад

I broker the top part of the sensor trying to twist, pry, back and fourth, etc etc...now the rest of the sensor is still in the head. Any tips? I went from the bottom up.

@obfuscated3090 8 лет назад

WARNING: Replace the intake manifold gaskets while you have the manifold off!! They are notorious for leaks (including mine which led me to find this video which illustrates manifold R&I pretty well). Rough running, the common P0300 Random Misfire, and other problems result from vacuum leaks when the manifold gaskets flatten and deteriorate.

@jacobtovarvallecastelan3634 5 лет назад

Hi! I got the same problem PO300 RANDOM MISFIRE. SO YOU RECOMEND ME DO THE. MANIFOIL GASKETS??? THAT'S THE PROBLEM. I DON'T HAVE TO REPLACE THE CMP?

@rolandoantunez2001 4 года назад

Ob Fuscated I have that code but no check engine light

@only1qu386 3 года назад

They switched intake manifolds is part of the reason. Take a closer look....8:24. They should've mentioned this. The manifold they put back on is the "Dorman style. It comes with individual gaskets installed around around each port.

@jake5210 3 года назад

May as well replace those knock sensors while you have the intake manifold off if they have never been replaced. They are also a notorious problem on these trucks.

@odiarroyo6144 3 года назад

im in the middle of finding what is making my engine misfire im trying to change all the sensors everything with oem parts and cleaning evening as a preventing maintenance i still don't know why is misfiring i still need to relearn it

@stonemills1546 Год назад

Do you not need to do a relearning process for a cam sensor? Just crank?

@mellowyellow8856 3 года назад

Does the camshaft sensor need a relearn like the crankshaft sensor? i replaced mine on a 05 Silverado SS and it will crank multiple times before starting now i have to crank it 4 or 5 times then it finally starts

@jwilli850 3 года назад

My 04 Silverado is doing the exact same thing, I had the camshaft sensor replaced, that’s when it started. Please let me know what you find out

@brandonburr1514 3 года назад

Any update? My trucks doing the same. Cranks for a bit then fires. Iv been chasing it for a year now 😡

@chrisyo295 3 года назад

After replacing the sensor do you need to do anything else or just erase the check engine light on ?

@jamesadam8515 4 года назад

Is it necessary to have cylinder 1 TDC before replaing? I replaced mine and it threw off my tach and cylinder 1 spark advance

@grannationalboy 2 года назад

@morganchase4822 2 года назад

PM how to test an LS cam positioning sensor out of the car

@arebelfromhell 3 года назад

what sensor is the one to the right side of the camshaft position sensor? the little tall guy with white connector. I broke mine trying to get back there

@brandonburr1514 3 года назад

Oil pressure sensor if you didn't figure it out already. Broke mine too 😂

@joehill647 2 года назад

My 05 Silverado stalls randomly. I could be going 20 or 70 on highway and stalls. Cold or warm still stalls. Once it stalls I wait about 30 minutes and it will start again and drive. Brought it to three mechanic and they can’t figure it out. Just replaced fuel pump and wasn’t that. Will this sensor potentially fix my problem??

@luislopez4145 2 года назад

My 01 Tahoe would do the same...you should check the crankshaft sensor I also changed the connector as well👍

@dtrust68 7 лет назад

So question....i changed my Camshaft position sensor in my 2005 chevy silverado. i also changed the starter. but now its throwing the low voltage/circuit Po342 code. would the Camshaft sensor maybe not seated properly or whats going on now? truck when on runs perfect. started perfect for a week with check engine on and yesterday it had trouble starting again. what could it be? battery is great. starter is new. my only thing im thinking is it not being seated properly so it could be off kilter and not getting good voltage. any help would be appreciated. Thanks

@dtrust68 7 лет назад

i messaged you on facebook...wouldnt a faulty Crankshaft throw a PO336 code

@leesale5832 5 лет назад

same problem. p0342. changed cam sensor 3 times. still code and hard to start every other time. runs great otherwise. new battery, new pcm, new cam sensor pigtail/wiring. traced all wiring and no breaks or grounding issues. changed crank sensor. Ideas? still have problem.

@JoseSanchez-qs7pl 5 лет назад

Hey Dustin, I know this is an old post but i was wondering what fixed your issue. I am having a similar issue with my 05 suburban. I replaced the camshaft position sensor but i still get the P0342 code. Next thing i am trying is to clean out the electrical connectors with contact cleaner and checking the wiring harness for any obvious damage. Any help would be appreciated! THanks!

@forrestgreathouse8902 4 года назад

did you figure out the low voltage problem?

@ericsalley3315 4 года назад

Did you figure out what the P0342 was. My 04 is giving the same code.

@joeburttschell1286 4 года назад

I have an oil leak mystery. Can the cam sensor possibly be the culprit.lv already replaced oil pressure sensor. Love your videos

@jake5210 3 года назад

It could be either of those. Or if the universe really hates you it could be the rear main seal/ rear cover which basically requires that you take apart your entire truck. Coming from experience in that endeavor, I wouldn't recommend it as a diy project unless you have a shop to do it in over multiple grueling days.

@jorgecruz5962 4 года назад

Ok What fo you need the vacuum?

@SmudgyContent 3 года назад

Guessing if there’s junk down in there clean it all out

@jamesadam8515 4 года назад

BTW I drive a 2003 Chevy Avalanche with the LM7 325 ETB

@tonywoodall6353 Год назад

Holy cow .. Just use a 10mm socket and a long extension from the top along the firewall. Takes 5 mins.

@guyballard2898 2 года назад

Please add the names of the parts that you are disconnecting

@texray1969 Год назад

I put a new camshaft position sensor on my 2002 chevrolet 5.3l and now I'm having starting problems and it backfires, why is this happening?

@ss55539 9 лет назад

you guys need an air ratchet lol

@canalesivany 5 лет назад

I replace my camshaft I didn’t do all this mess you guys are showing here

@scottfindlay2625 4 года назад

Oh good lord, you DON'T NEED TO REMOVE all that crap. you can do it in 30 min using a mirror so your not totally blind, i just did one on a 6.0 today.

@1AAuto 3 года назад

+scott findlay We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair.

@SmudgyContent 3 года назад

Yeah but what about the relearn?

@Mr10mikemike 3 года назад

No gasket for the intake?

@1AAuto 3 года назад

+Mr10mikemike Yes, the intake will have a gasket.

@thomasgerhart2290 2 года назад

You actually do not need to remove the intake if you just using wobbly and a wife extension and reach behind The intake

@DieselZee 3 года назад

Lol @ “just pry the sensor up and out”. Mine broke flush with the engine block.

@Mr10mikemike 3 года назад

Way to go Zach!

@sknejones4559 2 года назад

10mm Crows foot did the trick

@xSkittleBEASTx 9 лет назад

Is The Timing Chain Disturbed In Any Way? While This Process!

@1AAuto 9 лет назад

No. You should be able to follow the video and make the repair without any issues. Thanks for watching, have a great day. 1aauto.com 866-403-3393

@xSkittleBEASTx 9 лет назад

1A Auto Parts It Wouldn't Start At All- On My Tahoe 01' We've Swapped Out The Fuel Pressure Regulator and The Cylinder. Now It Starts, but only for a good 15-20 seconds. Could It Be The Cam or Something Else?

@MrGweezie503 8 лет назад

+1A Auto Parts I have a po420 with a po300? the po300 is at high speeds. the po420 comes on whenever

@4cooey 7 лет назад

LS engines don't have timing chains

@johncarambat4762 Год назад

I've seen videos where people just reach behind the engine between the firewall and the back of the engine unclip the plug use a 10 mm ratchet on an extension and just reach behind there and unplug it I've also heard some need to be disassembled this way for accessibility please Lord let me have the first situation

@35xcherry97 3 года назад

I see you got a newer intake manifold...🌚

@1AAuto 3 года назад

+La mamalona Chevy Thanks for checking us out! We use the same vehicle for several different videos/repairs each time we get one in the shop which is why some parts may be new in different cuts. 1aauto.com

@edwinbelmont2683 3 года назад

1000 liked right her

@1AAuto 3 года назад

+Edwin Belmont Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@fish4fun354 4 года назад

Why not just squeeze your hand back behind the engine instead of taking everything apart? 8:23 I thought you would have to replace the intake manifold gaskets since you took it apart....

@brianbanks449 3 года назад

You can literally reach around the intake and do this. I have no idea why they took the intake off. You have to work by feel but it isn't hard. These guys turned a 30 min job into all day - watch a different video.

@1AAuto 3 года назад

+Brian Banks Thanks for the tip! We'll pass this info along to our production team.

@justchillin9763 3 года назад

Have a video ?

@pax84111 5 лет назад

all that work just for 1 sensor ..

@snowconch8527 4 года назад

I broke the number 1 bolt on the intake manifold when attempting to torque to 89 in lbs. I did all the other 9 with no issues. The car has been running fine now for the past two weeks now. Should I worry about that broken bolt?

@clydecalamity6520 4 года назад

Ismael Nieves It might cause a vacuum leak on the nearby port. I would replace the bolt with a new one and torque it slightly less. But if you want to get away and just not do it, get a scan tool and look for a trouble code. Might be a misfire or a vacuum leak or say intake manifold, etc. If you don’t see anything or don’t feel the truck misfiring, you should be okay enough to just leave it as is.

@linc2356 3 года назад

That’s for a 5.3L

@69chevytrucker55 2 месяца назад

No need to remove anything lay across the front of the engine reach around the back use a ratchet with extension and will only takr 5 minutes tops to replace 😂