How To Fix Emergency Brake Actuators 00-06 Chevy Suburban

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,4 млн

Просмотров 241 тыс.

50% 1

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/247/c/brake-hardware
1A Auto shows you how to repair, install, fix, change or replace a broken or snapped emergency brake actuator. This video is applicable to the 00, 01, 02, 03, 04, 05, 06, Chevy Suburban, or Tahoe; or GMC Yukon.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oanJ/1AXAA00013
• 12mm Socket 1aau.to/o8G/1AXAA00015
• 18mm Socket 1aau.to/osP/1AXAA00043
• 22mm Socket 1aau.to/ocn/1AXAA00266
• 8mm Socket 1aau.to/oZi/1AXAA00017
• Needle nose pliers 1aau.to/onA/1AXAA00051
• Needle nose pliers 1aau.to/onA/1AXAA00052
• A Piece of Pipe (for leverage)
• Ratchet 1aau.to/oapo/1AXAA00016
• Torque Wrench 1aau.to/owK/1AXAA00044
• Floor Jack 1aau.to/ou5/1AXAA00068
• Hammer 1aau.to/omU/1AXAA00091
• Jack Stands 1aau.to/ovk/1AXAA00065
• Large C-Clamp
For More Info visit us at 1aau.to/h/bpg/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

27 май 2014

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 87

@1AAuto 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@KO-pk7df Год назад

Of course, the hardest part of all this adjusting the brake shoe to the best spot where it's not rubbing too much but yet getting effective e-brake that will hold the truck. These are lousy parking brakes and even after replacing the whole system with new parts and adjusting the best you can they will barely hold the truck to pass a safety inspection. So, after I get mine inspected, I never use them again until the next inspection. Even light use will make them ineffective within a year. I bought my 2004 Tahoe new in 2004 and have taken better care of it than anything else (according to my family) and I have yet to find any real solution to this problem.

@leeisenberg 3 года назад

Another good video, thanks for sharing. Thanks for the tool list at the 1st, And Especially thanks for sharing the torque specs at the end. - take care

@leeisenberg 3 года назад

Got a 03' Yukon, driver's side feels good, can't move w/ hands w/ E-brake on, but passenger's side still slips just a little in both directions. Ever seen that before? - thanks for all the good quality, helpful videos

@donnaswan875 7 лет назад

Great video. Helped a lot. Just in time... etc... btw you installed the retaining clip backwards. The ears point back to keep it from spinning and it holds the shoe back further when installed correctly.

@1AAuto 7 лет назад

+Donna Swan Thank you for watching, as well as the feedback. We will ensure that our Studio is aware of this and they may edit to notate for complete advice for other viewers. 1aauto.com

@kdlittlehawk 4 года назад

@@1AAuto caught that too..also dabbing that adjuster with some Never-seize is always a good thing to do.

@marklesko 2 года назад

Ditto on the backwards retaining clips. I love 1A Auto videos, but you really need to edit that since it's so important. It's actually the main reason I wanted to watch the video: Mine were installed backwards by a previous owner and I needed to determine the correct orientation of the clips.

@lsimpson6223 2 года назад

One added recommendation is to lubricate the friction surfaces where the horseshoe e-brake rides. And always always lube the adjuster, application cup, pin, and bore before reinstalling. Also lube brake pad slides. Just like in married life, never put in dry. 😱🤣🤣🤣

@darthhulka-burger3187 2 года назад

Thanks to 1A for the great video & your series of videos. They are very much appreciated 😀 We all know that it is ridiculous to have to go through all that hassle just to adjust the Emergency Brake on the vehicles. But.... I will say it again:. Why GM? Couldn't you engineer something else to fail or require a visit to the Service Dept? This oughta be a 1 minute adjustment....but Noooo😵‍💫....

@robfaris26 2 года назад

I am not a mechanic just a DIYer, but it appears the bracket at 4:45 needs to be mounted AFTER the brake shoe assembly is in place instead of before (as shown) so the bracket can be positioned INSIDE the brake shoe assembly to prevent it from rotating.

@lsimpson6223 2 года назад

Shoe retainer is also mounted backwards in video.

@daviddensmore2606 7 лет назад

Thanks, this helped me ensure I was putting mine back together properly. I took them off a while back, and I'm only now replacing them, so this helps verify the memory. I would note that unless you live in the desert of Arizona, the adjuster's screw threads and the outside of the adjustment barrel should receive a coat of antisieze. Here in NE Ohio, they wouldn't function very long.

@juncboi 10 лет назад

Great tutorial. Now, if I can only find the kit on your website. Please post part # or link?

@kdlittlehawk 4 года назад

that single horseshoe e brake pad design is a real hassle.

@rangoonred1881 3 года назад

good video. i adjuste3dmy parking brake on my 2001 Tahoe per your video. the park brake cable still goes to the floor with little resistance, don't want to over expand the shoes or the car will struggle to move and wear out the park brake shoes. there must be some cable stretch problem the car has 230000 miles on it. what should i do

@ciscochacho1751 Год назад

Thanks for sharing

@tallbe1 5 лет назад

What do I replace on if the cable broke off behind the backing plate of the hub, 04 GMC Sierra 1500. Need that for state inspection.

@1AAuto 5 лет назад

+Brandon B. Irish Thank you for watching! You will want to replace which ever cable that is that broke, whether it be the parking brake cable, or ABS cable. 1aauto.com

@mijohnst 3 года назад

Here are a few things that I learned from watching many of these videos that helped me with mine. I've had a Yukon and 2 Tahoe's and done the breaks on all of them. 1. When adjusting, use plyers, not a screwdriver. So much easier! 2. When making adjustments, make sure to have the rotor on the other side off while you're doing it. Do the same for both. It removes any 'phantom' resistance you think you might feel during testing. 3. Turn the adjustment dial clockwise (expanding) until you just cannot get the rotor all the way on (don't force it) and then back it out about 2 clicks. 4. Don't forget to grease up all the contact points that the edges of the brake shoe are going to touch. There are 4 points. 5. Don't forget to grease the back of each brake pad and metal clip contact points that hold them when reinstalling. I even put a little grease on the piston rings and boots on the caliper. 6. It's already been pointed out, but the retainer clip in this video was installed backward. Honest mistake, I did it backward too once. With the clip screwed in (don't crank it down too much), the shoe shouldn't move much at all in or out.

@andrewhigdon8346 3 года назад

Doesn’t the adjuster turn one way for driver’s side and the opposite for the passenger side, as the direction of the vehicle dictates the adjustment? It used to be that after doing a drum brake job, that star wheel tab adjuster would ratchet until firm when braking from reverse, which “automatically” adjusted the drums to the preferred clearance. Of course all of the components needed to be in proper working order. So about the grease on the back of each pad, why is that? Reduce chatter? I could see how on those GM trucks the three clips which fit into the piston could use some “anti-screech” lube for a worst case scenario. But what about the outer pad?

@rickkoch1552 5 лет назад

At 4:52 isn't that clip in wrong? It should be flipped around where the clips cradle the contact point of back plate. Just curious.

@AlexGZ9 7 лет назад

great video thank you! When I changed mine..one of the retaining clips, the screw was broken. how can I fix that? or how do I get that broken screw out if there is not much space to get to it? thanks or can I use something like J_B weld to retain the clip in place? ??

@JacePriester 3 года назад

I know this was 3 years ago.. but in case anyone else sees this... Hammer out a wheel stud. You can then spin the flange and get access to the broken retaining screw through the wheel stud hole. Use a screw extractor as normal. Can even drill and re-tap the hole if you need to. The hard part is putting the wheel stud back in, which you will need a very heavy duty C-clamp for. You can rent a torsion bar unloading tool from your local parts store, which is effectively a VERY beefy C-clamp, and use that with an impact and some spacer blocks to re-install. The alternative is to open up the diff and remove the axle shaft.

@darthbart1972 Год назад

@@JacePriester awesome comment...my buddy's in the same boat! He was about to take out the whole axle. Thanks!

@Big_daddy_1170 3 года назад

Use pliers to turn the adjuster. Super easy

@slarsen32 3 года назад

My 2002 Camaro has a similar parking brake adjuster. There is a lever on the back side attached to the cable. The lever does not engage the adjuster. It just moves freely from side to side and will not come out and cannot be pushed in. How do you get the lever back in place so that it operates the adjuster?? What holds the lever in place so that it can expand the parking brake??

@anotherpewtertahoe 2 года назад

Mans needs to chill with the caffeine, holy hell I thought I was gonna have my own seizure.

@carlkuwait5753 2 месяца назад

The lever behind that the cable hooks on is what is broken for me. Unfortunately this part is not found on your web page. The lever moves but does not move the actuator shown here. Any idea where to find that part?

@jmihalic3224 6 лет назад

Can you get to the adjuster from behind the plate so you know it's adjusted right

@kdlittlehawk 4 года назад

nope

@DjTragik951 2 года назад

Is there a way to fix the piece behind that holds the cable?

@valentinerodriguez2265 5 лет назад

Thanks for the video, I only have a question about it I changed my break pads as well the grum shoe break but the light of the emergency break doesn't turn off did I did something rong i well appreciate if you could help me out

@1AAuto 5 лет назад

+Valentine Rodriguez Since there could be multiple reasons why you’re experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. They’ll be able to troubleshoot the problem and tell you what part or parts you’ll need for the repair. This could either be an issue with the actuator or something that was done during the shoe installation

@JesusGuerrero-fe3du 3 года назад

Did you guys figure out what went wrong my brake light is on and my abs after replacing the e brake pads?

@thesetruths1404 2 месяца назад

I bought a 2005 Yukon, 218,000 miles, and the parking brake cable in the cab was missing so I replaced it. Then I realized the parking brake doesn't engage enough to stop it from rolling from even a slight sloping hill, entirely empty. So something is not working right. How should I confirm what is broken? Are there other components that can fail that would cause the parking brake not to work? Should I disassemble both rear wheel rotors and visually checked it out? Thanks!

@luissierramacias2463 2 года назад

I have a 2002 suburban, the rear break get stuck and make a big squealed noise when I'm driving, what is coming problem for break on this vehicle, thanks.

@bwagenberg 2 года назад

You really should reshoot this with a modern good cameraman.

@ecgodsmack86 4 года назад

Do you have to do this to both rear wheels? All 4 or just this one?

@chadseifert3374 Год назад

All four?

@matthewfaus9087 3 года назад

Can u put on the backing plate without taken off the the axle

@juancarlostapia53 3 года назад

I wonder the same question...how did put the black cover ??

@frenchfriedhonky6554 5 лет назад

I have a 98... Is it possible for these parts to make a grinding/scraping noise when accelerating if parts are broken?

@1AAuto 5 лет назад

+Sam Sancho it is

@davidh4538 5 лет назад

Yes it is. I had a intermittent rubbing scraping noise. Came and went. One of the shoes came unbonded from the horse show thing and was floating around in there. ha

@rad3766 3 года назад

@@davidh4538 Yup, just went thru this on my Silverado, intermittent scraping noise, was driving me crazy.

@johngembka7052 5 лет назад

What is the part number for the backing plate you also changed?

@1AAuto 5 лет назад

+John Gembka You can find those backing plates at the following link, please be sure to check the vehicle fit list and ensure you choose the correct one: www.1aauto.com/search?q=backing+plate&year=2002&model=2152 1aauto.com

@williambritcher8510 Год назад

It appears that the brake retainer clip was installed backwards. Other then that it was a great how to.

@mbravo9854 9 месяцев назад

I don't know where you guys got your torque specs but I'm positive wheels are 140 ft lbs and I think the bolts for the caliper brackets are 144 ft lbs

@meximota 2 года назад

You don't have to remove the pads to remove the adjusters. But in case you want more room then remove them, but for me i left them on. Just to much work trying to put them back on.

@mark9ze Год назад

For the life of me I do not grasp why GM even is using the top aduster into the casing (gear) part in this e-brake???? If the pill gets pushed down with the pull on the cable then what does the top portion do? When I removed my e-brake pad, only half of it was worn, the portion at the non pill side was like new. Does it need to be manually adjusted on ocassion and is not self adjusting?

@nickazar7846 4 года назад

Is it the same for the left and right side of the car?

@JacePriester 3 года назад

Yes. One side is flipped upside down. No differences though.

@102cars 2 года назад

One addition, make sure you use threadlocker or new bolts for the caliper mounting bracket when reinstalling! They're a known failure point on GMT800s.

@jrgreen426 7 лет назад

You might want to mention to make sure you bend the tabs back in on the dust shield or they will rub on your rotors. Not a good sound.

@2Ramrod2 5 лет назад

??? What tabs...

@johnnyowens6757 2 года назад

Yes that happened to me. I had to take it back apart to bend them around.

@baloneynoodles2.0 7 месяцев назад

I need those parts how do I get ahold of them

@jimgaskell1833 2 года назад

The shoe bracket you installed is flipped over backwards to the original ones my vehicle.

@markwebster1952 2 года назад

is there a way to tighten the parking brake without stripping everything down?

@lsimpson6223 2 года назад

Can tighten the equalizer block on the rear of the intermediate cable, but impossible to move the adjuster inside on brake shoes without tearing it apart. 😞 sorry. If only that was a possibility.

@Dpjones75 4 года назад

I think you installed the retaining clip in backwards.

@JacePriester 3 года назад

Yep that's definitely installed wrong.

@tuscani915 3 года назад

I cannot find this kit on your website, do you have a link to it. I tried by application, but do not see this kit.

@1AAuto 3 года назад

+fernando tarango We do apologize but we just offer the install video and not the part.

@tuscani915 3 года назад

@@1AAuto ok, you might want to change the description on the list, shows Emergeny kit from 1aauto.com. that's why I asked why I can't find the part on your website.

@uwebuehrle6381 Год назад

And to adjust the parking brake shoe ??

@REVerbtalk 5 лет назад

They make it appear so easy... I replaced all lines that, the brake shoes and STILL the parking brake goes to the floor as easy as hitting the gas pedal. Yes, I've adjust the suckers so much I purposely hard pressed the rotors back on only to find out is still not holding not even enough pressure for an ant to stop moving... What could possibly be wrong at this point?

@guitarguy3221 9 месяцев назад

Ive seen so many people have the same problem with these brakes without an answer. Very interested in the solution lol

@bangbang-ko2gi 5 лет назад

On that vehicle that wheel is supposed to be torqued to 140! An under torqued wheel is very dangerous.

@2Ramrod2 5 лет назад

I was going to say something about that but you beat me to it!! Not only what you said, it will also ruin the pads and rotors not being torqued correctly...