Installing a Hydraulic Transmission Into My CRX - Innovative Cable to Hydro Actuator & Motor Mount

Подписаться 93 тыс.

Просмотров 19 тыс.

50% 1

Step Drill Bits - amzn.to/3D5lXVT
Milwaukee 3/8" Ratchet - amzn.to/3wC1WDZ
PCI Side Skirts - jhpusa.com/search?q=pci+side+...
Innovative Mount & Actuator - jhpusa.com/search?q=innovativ...
Purchase Maxpeedingrods parts in the link below!
www.maxpeedingrods.com?tracking=58deec5d-3b72-49e7-bfe2-aae52bcbb8af
Use Coupon code "GBH" and receive 15% discount on all orders.
Parts I Use frequently -
Wheel Bearings - amzn.to/2RjiHn4
Nitto NeoGen 205/50/15 Tires - amzn.to/3impO8I
Skunk2 Camber Kits - jhpusa.com/search?q=skunk2+ca...
Cameras used in this video
My GoPro - amzn.to/2YQ3OGZ
My Mirrorless Camera - amzn.to/2HzzFFT
Send me stuff here!
Jon Widmer
PO Box 13594
El Paso, TX 79913
/ garagebuilthondas
Thanks for watching!
Disclaimer
"Due to factors beyond the control of Garage Built Hondas, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Built Hondas assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair videos. Due to factors beyond the control of Garage Built Hondas, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again, any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Built Hondas."
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll potentially receive a small commission at no cost to you. This will help support the channel and allows us to continue to make videos like this. Thank you for you support!

Авто/Мото

Опубликовано:

9 ноя 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 136

@Busydadgarage717 2 года назад

Happy to see this update. Been checking every day since Saturday. Lol. I have the opposite problem for my trans. I have a YS1, but converted to hydro pedal assembly. I think I may just revert back to cable setup to make things easier.

@BRENDAJASON1 2 года назад

I might as well scrap my b engine even though needs rebuilt doing me no good where I am can’t find a b trans harder to find than than the engines

@joshdane5657 2 года назад

You can buy a rebuilt one from synchrotech or manual gearbox LLC. I think even geardriven is selling them. They are expensive but worth it. Or if you're broke like me get a used one lol. I paid 350 for both of my small spline LS cable trans one from a friend and one from eBay. They cost alot more for a b series than a d series but its worth it. You could use a hydraulic trans they are easier to find usually.

@BRENDAJASON1 2 года назад

@@joshdane5657 I think I’ve found one few hours away from me

@AndToTheRepublic4WhichItStands Месяц назад

@@joshdane5657nobody building Honda's in their garage has $3000 to drop on a 90s Honda transmission tho

@Edony8 2 года назад

Love the videos and all the cars. Keep it up!

@KMFDM781 2 года назад

I had a similar hydro/cable bracket on mine. I originally had an ebay one that liked to bind up sometimes and the geometry was wrong. My clutch pedal was cocked out so far left that it wouldn't go down far enough to release the clutch. I had a somewhat heavy Competition Clutch pressure plate that was in the car when I got it and I destroyed 3 pedal assemblies. The one that was in the car when I bought it was already pretty messed up....then I killed two CRX assemblies (which are stronger) and one plain EF assembly. I swapped to the bracket like yours and went to an Action Clutch 4 puck unsprung unit and it was much much better but still too much for a stock EF pedal assembly and it was starting to bend after a month or so. I went to the Hush cable to hydro conversion shortly after I noticed the bending and had zero issues afterwards. I actually was able to force their slave cylinder bracket onto the bent EF assembly and it lasted until I sold the car. That bracket is heavy duty and really triangulates the weak spots in the stock assembly. I don't know if you can still buy it by itself but it's worth it even if you plan to keep the cable and conversion bracket setup.

@GarageBuiltHondas 2 года назад

Thanks for the super interesting share. I'd love to do the Hush Performance setup that they still offer which is full hydro, but these parts were essentially "free" so I decided to use them for now. I may actually sell and get the Hush kit once the season is over.

@Spaghetti-O 2 года назад

Helpful video as always! I have a known solid hydro LS trans with installed LSD for a B20 swap in by 88 CRX SI, wondering what the best option was for cable to hydro. Hush kit looks sweet but for 88 you have to swap to a later pedal assembly which is kind of a bummer.

@peterbryant3584 Год назад

Great video great content

@arockpcb1347 2 года назад

Yes, my same cable to hydro set up melted the plastic adjustment screw. Now I have to check it often.

@GarageBuiltHondas 2 года назад

That's no good!

@saraithompson8169 2 года назад

The itr tranny is a great choice for the track you’ll be in your powerband majority of the time and an upgraded lsd as well makes it so much more fun. Surprisingly enough too is with the 4.7 fd you really dont see a hit in mpg as most people would think

@GarageBuiltHondas 2 года назад

👍

@666gnarlsbad 2 года назад

Love your videos bro. Shout out from Carlsbad New Mexico🌶

@GarageBuiltHondas 2 года назад

Yo! Thank you!

@Philthese93 2 года назад

Random Wednesday video!! Thank you 🙏

@GarageBuiltHondas 2 года назад

👍

@leoflako13 4 месяца назад

I have a 92 GSR that came swapped with a b18ba2? w a 2 speed manual transmission…. Now a b18c1 is going in with its hydro 5 speed transmission… currently made a full hydro conversion with the master cylinder on the pedal assembly…. Just curious to see if I need new axles or do the axles on the b18b1

@codykerns9051 2 года назад

need some of that woven heat shield stuff for your header's, might keep that cable from melting at least a little bit longer but I'm sure it's not full proof.

@flacorodriguez5798 2 года назад

Yes yes finally content ..........thanks

@GarageBuiltHondas 2 года назад

👍

@thebestever2774 Год назад

Is a sick car♥️🔥

@GarageBuiltHondas Год назад

Thank you!

@uses0ap 2 года назад

16:39 Diggin that window crank lol

@GarageBuiltHondas 2 года назад

Thanks to a good friend and crx lover also!

@GTS_-oq2op 2 года назад

Thanks Jon! Another good tutorial video 😃 anyways what suspension setup you’re running right now?

@GarageBuiltHondas 2 года назад

This! ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-eygasOOMz6M.html

@marionoh6743 2 года назад

Donde puedo comprar el kit de la tranmicon

@robh23a1 2 года назад

HOPEFULLY YOU CAN HELP!!!! Does a jdm b16 transmission work with ls axles ON A B18B MOTOR ??? I heard that you need to run 90-93 integra axles non abs an use a b16 intermediate shaft for it to work

@GarageBuiltHondas 2 года назад

What car?

@anthonygutierrez3515 Год назад

How would you be able to tell the difference between a b18 or b16 cable trans with out opening it up

@GarageBuiltHondas Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-HDbKTyXnnOI.html

@Mr.Gal1kanokus 2 года назад

You da man 💪

@GarageBuiltHondas 2 года назад

🙏

@sladdar Год назад

Hey! I noticed your traction bar in the video. Can you share the brand name of that traction bar and were to get it?

@GarageBuiltHondas Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-xAJuFNAtX_I.html

@EazyZ510 5 месяцев назад

Did the cable to hydro have any issues with heat next to the header

@GarageBuiltHondas 5 месяцев назад

I didn't experience any.

@pdusty7707 2 года назад

Hey Jon, don’t know if you already swapped to a smaller throttle cable, but an eg cable works as well! I used one on my z6 swapped EF, and it fits perfect in the pedal and will get rid of all that slack. Mine was getting stuck on my neuspeed strut bar and sticking open! Super sketchy!!

@GarageBuiltHondas 2 года назад

Thanks for the tip, I'll probably order one when I remember too!

@pdusty7707 2 года назад

@@GarageBuiltHondas no problem! I took a small vacay from efs, but just recently traded a gs300 I paid $2k for, for a b16 swapped fwd wagon, and an RT4WD wagon. I’m happy to be back in one everyday lol

@GarageBuiltHondas 2 года назад

Nobody ever really leaves EFs. Lol

@angelodivincenzo9190 10 месяцев назад

I’m in the process of ordering my cable to hydro kit, just checking if you’ve gotten the hasport kit and wondering which one you prefer?

@GarageBuiltHondas 10 месяцев назад

The Hasport one worked fine. I'm full hydraulic now and prefer that way more

@jdmgatekeeper5849 Год назад

Hey I’m dropping a b16a2 into my 1990 integra DA. What distributor, alternator and starter do I need for my set up to work? I’m using the stock harness from the Integra da.

@GarageBuiltHondas Год назад

All obd0 parts.

@kaybevang536 2 года назад

What happens if I put a Usdm Del sol b16 tranny same process on my da9 ?

@GarageBuiltHondas 2 года назад

Yes

@pnwgamerguy8030 2 года назад

I'm in process of doing a d series hydro trans swap with hasport conversion.. hope I like it, I couldn't find a 88-91 si trans to save my life..

@GarageBuiltHondas 2 года назад

Feels solid. I'll be trying a full hydro setup hopefully this summer.

@throughmyeyesmedia6492 2 года назад

Nice transmission pick up and I was going to ask on the speedo sensor if you were going to sell it lol but you used it on the transmission.

@GarageBuiltHondas 2 года назад

For sure man!! Thanks!

@cedriccope178 2 года назад

Finally!!!!!

@GarageBuiltHondas 2 года назад

Still feels like cable.

@cedriccope178 2 года назад

Boooo

@GarageBuiltHondas 2 года назад

It'll take a full hydro setup to feel different. Not ready to commit that kind of money just yet.

@jonnymiskatonic 2 года назад

Nice work as always! I'm debating on what to do with my wagon. Can't decide if I wanna keep the D or swap to a B.

@GarageBuiltHondas 2 года назад

Do what your budget allows, otherwise it becomes stressful. 👍

@edvas02271 2 года назад

I'm in the same situation but the wagon only has 119k miles. So healthy rides so smooth but soooo slow lol

@GarageBuiltHondas 2 года назад

Nothing wrong with a cruiser at all. Enjoy it, those are fun! The more mods and more power you make the more stress you create. It is fun though!

@kellywesley1977 2 года назад

Hey what does that speed sensor come out of

@GarageBuiltHondas 2 года назад

All cable manual trans.

@theimporttuner399 2 года назад

Whats the update on the pedal feel using the actuator?? Do you like it? I purchased the innovative h22 ef mount kit that comes with the actuator. Im hoping it feels good enough where i won't have to go full hydro. Well lmk how you like it so far?

@GarageBuiltHondas 2 года назад

Feels like a cable setup still. It's fine.

@jdmgatekeeper5849 Год назад

Hey, did the speed sensor work? I noticed you used the cable transmission speed sensor and put it in the hydro transmission.

@GarageBuiltHondas Год назад

Of course it did. 👍

@jdmgatekeeper5849 Год назад

@@GarageBuiltHondas so I can do the same thing and put a cable speed sensor into my b16 hydro trans that’s going into my 1990 integra?

@GarageBuiltHondas Год назад

Yes

@The_Redkween 2 года назад

Love this video! I went with a cable-tranny because it was the first available but it had no markings on it. How do you tell if it’s LSD or open? Thx! Still it in the car, btw

@GarageBuiltHondas 2 года назад

Remove an axle and look in the diff. A bar in the diff equals no LSD.

@The_Redkween 2 года назад

@@GarageBuiltHondas thanks, Jon! I have an open. :(. Oh well, it’s all I had available and I’m just putting n a stock JDM B16a anyway. Not power hungry, just want more track ability

@GarageBuiltHondas 2 года назад

LSD really isn't necessary unless you're tracking you car very often and you're driving skills have exceeded your parts. 👍

@The_Redkween 2 года назад

@@GarageBuiltHondas well that certainly hasn’t happened. 😂

@GarageBuiltHondas 2 года назад

One day you'll get there!!

@AXONOMETRIC 2 года назад

Hey Jon, Are those the buddy club wheels? Do they rub at all? Thinking of getting some for my CRX.

@GarageBuiltHondas 2 года назад

You'll need rolled fenders and negative camber.

@josuecrx 2 года назад

I have a question, you had to bent or smash the frame to fit the b series alternator?

@GarageBuiltHondas 2 года назад

This car was never hammered, I found this out when I had to swap the alternator belt. I was able to find an extra belt that I had lying around that was shorter and it worked. I prefer to hammer the frame rail though and will one day when I pull the engine.

@josuecrx 2 года назад

@@GarageBuiltHondas Thanks!, I saw many crx that needed to be hammered, but i dont knw why, because the jdm sir came with a B series. I have a fitment problem with my B series alternator so i want to see a solution without hammer it.

@1991jdmcivic 2 года назад

Are those skateboard wheels on the window cranks?

@GarageBuiltHondas 2 года назад

Yes

@chasstiltner3571 2 года назад

What hardware did you end up using on the side skirts? The screws pci provided me were a little on the short side

@GarageBuiltHondas 2 года назад

PCI provided. Everything worked perfectly.

@GarageBuiltHondas 2 года назад

It just installs directly over the plastic. Email Brian from PCI. He had sent me the instructions but I tossed them. It's so easy to install them.

@Cruz99juan Год назад

Does it work for a d series transmission?

@GarageBuiltHondas Год назад

They do make one

@levylovits 2 года назад

Jon is there any way you can make a video of what every electrical part is and does. I got wires under neath the steering column that are almost melted showing bare wire. Most of the wires are sleeved with duck tape. I ran my car hard yesterday which i know i shouldnt have done. After the session i was driving back yestderday and the car died on me. It wouldnt start i didnt hear the fuel pump prime but i did felt the relay clicking. I disconnected the battery checked the fuses #8 was blown but all the instrument lights were working. The fuse was 25amp. I noticed none of the fuses are what they are suppose to be all mixed matched amps. I got wires cut or frayed. Relays or fuse boxes not bolted to anything. This goes back to my request in that maybe if you can help out with naming electrical parts so i can cross refrence them to a wiring diagram. Maybe if hints on sensors if swaps are to be done like d15 to d16/zc This moring again the car cranked but no start. The only thing different from before to now was zip tie the wire rats nest under the steering column so that i would rub the wires with my leg. I touch the wire nest with my hand and it started up. Got to work and tried it again. Started. I know my o2 was giving me problems before. Replaced it recently but i think its still giving me problems. Had code 1 last night moved the wiring no code. I need to spend more time following wires and labing them and checking out pins

@GarageBuiltHondas 2 года назад

Sorry, I just don't have the time. I only make videos of what I'm currently working on and I've got my hands full with all the things I want to get done to my cars and hardly enough time to work on any of it.

@levylovits 2 года назад

@@GarageBuiltHondas thats how it is man. I just got a pdf service manual online free. Im going to read that puppy like no other. I learning everyday about this car. I got zc but it has dual point. I replaced the o2 but now im getting similar problems of what i had before. Rpm not doing down after i shift. On top i have a leak in the exhaust somewhere. It never ends but itll come through. Engine mounts are done though atleast

@GarageBuiltHondas 2 года назад

That'll work. Good luck!

@dustyumbreon5472 Год назад

i wanted to ask how your experience with the innovative mounts were, im considering them myself for my d series ef as a replacement for oem and wanted to know if there were any concerns with fitment or durability

@GarageBuiltHondas Год назад

None. Hasport or Innovative is the way to go.

@Mr.Noz11 2 года назад

Any updates on the Ef sedan

@GarageBuiltHondas 2 года назад

Not yet. Want to get on it during the off-season.

@johnplate9367 2 года назад

I have the same setup on my crx . Mine rubs my header . At a stand still till I get a new header

@GarageBuiltHondas 2 года назад

Which header?

@Brianlsvtec 2 года назад

Do you have any issues with the trans hitting the passenger side frame? My b16 hydro trans is hitting the frame on any kind of hard shifting or taking off.

@GarageBuiltHondas 2 года назад

Zero. And I tracked it once with this setup. If you're using generic mounts, that may be the problem. I'm using Hasport with the softest bushing and no issues.

@Brianlsvtec 2 года назад

@@GarageBuiltHondas I'm using innovative billet mounts with the 95a inserts. I had this same setup in my sedan and it never hit but it hits in hy hatch. Kinda interesting, maybe I can loosen the mounts and move it over a little? If not guess I'll be adding a midplate mounted to the traction bar lol

@GarageBuiltHondas 2 года назад

That's too bad, maybe do as you said, loosen them all and shift it over and tighten again as the engine is being pushed over.

@Brianlsvtec 2 года назад

@@GarageBuiltHondas I took the passenger mount off and it was slotted. I got it all fixed now👌

@ericvang5930 2 года назад

I have the same cable to hydro kit but I noticed that your clutch fork is different than my itr. Which clutch fork are you using that’ll allow for the piece to connect to it?

@GarageBuiltHondas 2 года назад

Couldn't tell you. Looks stock to me. I got the trans from a parts car so I'm unsure if it's a different fork. My guess is all B series forks from 92-01 should be the same as all those transmissions have the same sized input shafts and gears.

@ericvang5930 2 года назад

@@GarageBuiltHondas I see. Do we just push and squeeze the ball on the bracket into the fork?

@ericvang5930 2 года назад

Sorry to bother you again, but is there anything holding the end piece that’s pushing the clutch fork in place? Or is it constant pressure from the tranny that’s not allowing it to slide out of the fork? I’m currently working with the same setup, except my tranny isn’t mated yet to block.

@GarageBuiltHondas 2 года назад

Don't understand what you're saying, sorry.

@Brad-jv6ge 2 года назад

What is that vss off of?

@GarageBuiltHondas 2 года назад

Which?

@manuelortega797 2 года назад

So I'm doing a b20 ls trans in my ef I was wondering if you had any info on how to get the speedometer working with it dose it just switch over or dose it have to be a specific year 🤔

@GarageBuiltHondas 2 года назад

You didn't mention speedometer sensor

@manuelortega797 2 года назад

@@GarageBuiltHondas yeah my bad are the speedometer sensors interchangeable as well 🤔

@GarageBuiltHondas 2 года назад

Yes. Just need a cable sensor

@manuelortega797 2 года назад

@@GarageBuiltHondas hay man I really appreciate you sharing this Info and honestly keep up the great work with the videos I really enjoy and learn alot from watching you thank you happy holidays

@manuelortega797 2 года назад

@@GarageBuiltHondas one last questions what year make and model should I be looking for

@gfy498 2 года назад

Ok can y’all help me out I need to find what those 2 brackets he using on left side the motor mount bracket and the one that the transmission has y’all please help me find those brackets. I need those to be able to put my engine in my car all I need is those 2 brackets on the left side of the transmission

@GarageBuiltHondas 2 года назад

Here's the rear bracket. amzn.to/3NuVy93 The other one is a stock bracket you'll need to find.

@haystack8569 2 года назад

hey what hardware do i use to bolt this up to my gsr trans?? anyone with anything is much appreciated 💪🏼👊🏼

@GarageBuiltHondas 2 года назад

If purchased new it'll come with hardware.

@haystack8569 Год назад

@@GarageBuiltHondas thanks guys much appreciated. 👊🏼

@GarageBuiltHondas Год назад

If not contact Innovative. I'm sure they'll send you some if you ask, maybe even for free.

@efnmadaboutcivics88 2 года назад

While were on the topic of transmissions, I have a 90 DX hatch with an automatic and DPFI. I was wondering if I could use a 92-95 civic automatic trans for my 90 D15. I am trying to see if I could mpfi swap it and keep it automatic. I know 90's are cable and 92-up are hydraulic but does that matter with Auto's?

@GarageBuiltHondas 2 года назад

Good question, I have zero clue. Never researched it. My guess is the 2 mounts on the transmission would be completely different.

@efnmadaboutcivics88 2 года назад

@@GarageBuiltHondas that was my guess too. The kickdown cable is the only snag in my plan lol. Guess I'll just tear it apart and try.

@reifonseca5767 2 года назад

I dont think so to old .i know you can use and swap back and forth 92-95 96-2000 but not 1988-1991

@reifonseca5767 2 года назад

Bcuz the electronic part of it not just speedo sensor

@estewar03 2 года назад

Hey Jon, if you want some heat wrap for your header to help protect the clutch cable hmu via email. Also, for the sunroof delete, I think you're talented enough to make your own carbon fiber panel for it. "Bills Build & Race" formerly WJP004 youtube channel has amazing & easy to follow tutorials for almost anything automotive & carbon fiber/fiberglass related. It'd be easy & cheap & make for a cool video I'm sure your subs would enjoy.