N55 Oil Filter Housing & Oil Cooler Gasket Replacement | BMW X3

Подписаться 47 тыс.

Просмотров 34 тыс.

50% 1

Learn How to fix that leaky Oil Filter Housing Gasket as well as the Oil Cooler Gasket on the N55 Engine.
Thanks for tuning in. If you are looking for a complete tool kit as well as video gear hit the links below.
Ratchet: amzn.to/3IbXCjS
Torx Set: amzn.to/3dqrFGs
Socket Set: amzn.to/3Il3wzo
Plastic Trim Tool: amzn.to/31hBMdM
Extension Set: amzn.to/3EwXIjX
Charge Pipe: tinyurl.com/N55X3CP
Tool Kit: kit.co/fritzramos/bmw-mechani...
Video Gear: kit.co/fritzramos/filming-gear
If you are looking to get started on RU-vid, consider Tube buddy as it has helped me out a great deal. Try it out for free: www.tubebuddy.com/financialfi...
Some of the above links are affiliate links. By using them you help support the channel at no additional cost to you. Thank you for your support.
00:00 Intro
00:38 Signs and Symptoms
00:59 Getting Access to the Main Bolts
03:05 Draining the Coolant
03:35 Removing the Oil Cooler
04:10 Remove the Oil Filter Housing
05:12 Remove the old Gaskets & Clean the Area
05:30 Install New Gaskets
05:47 Install Oil Filter Housing
06:48 Reconnect Coolant Hose
06:55 Install Oil Cooler
07:21 Secure Intake Manifold
08:02 Reattach brackets and sensors
08:22 Airbox Installation
09:03 Top Off Coolant
09:15 Reinstall Engine Cover & Torque Oil Filter Cap
09:22 Tips & Closing Thoughts

Авто/Мото

Опубликовано:

7 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 81

@daywalker4321 2 года назад

there's plenty of good tutorials on youtube regarding this topic.... but this has to be the best informative video yet. Loving your work!

@FritzRamos 2 года назад

Thank you. That means a lot. 🙏 You're right, there are definitely a bunch of good videos on this topic.

@dakarrifindsout9404 2 года назад

That’s the first thing I said

@abrahampadilla959 Год назад

I’ve been watching a couple of tutorials on this job and I gotta say this is by far the easiest/simplest walk through thank you 🙏🏼

@kencorwin8341 5 месяцев назад

The problem with using the 12-point ratchet on the E-torx bolt head is that it easily strips the bolt head and makes it much tougher to remove. Much, much tougher. Hours of tougher. If that bolt head gets stripped, your estimated 90-minute hour gasket replacement job becomes quite an ordeal, given how already-difficult it is in the first place to reach that bolt and get leverage on it. So, when you get to the point that you’re about to remove that small bolt, first disconnect and move aside the cylinder head temperature sensor and the hose just beneath that sensor. These are located at the front of the engine, just to the left of the OFH. When you pull the sensor clip, do it **carefully** as the clip can fly away, it’s not secured around the sensor. The adjacent coolant hose is attached to the engine via two simple 8mm bolts; just be firm but always gentle when pulling any hose. With these out of the way, you can fit a proper ratchet wrench with E-torx socket onto that very soft bolt head and avoid stripping it.

@jwherron 6 месяцев назад

Good stuff. I cannot stress how important it is to torque the 4 bolts that attach the cooler to housing. They can be easily stripped. Great job! Thank you for the video! 👍

@jasonfirko1370 2 года назад

Great video. I appreciate the details of how to get to each bolt and the sequence. Makes me feel sorry for the folks trying to get that small filter housing bolt off first, doing it your way was pretty easy, except when I dropped my socket and had to fish it out. Thanks again.

@FritzRamos 2 года назад

Thank you for that. Don't worry the socket drop is something we all struggle with 😆

@dakarrifindsout9404 2 года назад

Thank you so much for the information I don’t know why the likes don’t match the views I like how you explain and don’t even skip a step 🙏

@larryt9176 4 месяца назад

Older vid but please ensure you take the extra step to prime the oil system after everything is buttoned back up.

@zildog Год назад

That engine is going to go kaboom if it hasn't already. You didn't pull the fuel injector wiring so that it doesn't fire up. You MUST prime the system with oil and purge it of any air you just trapped in there when you put it all back together... How do so many people not understand this??

@jtflem11 2 года назад

Thank you for making this awesome, very informative video

@tallerdefab 11 месяцев назад

Great video !! very well explained

@TTsmashers Год назад

Jealous that you don’t have to remove your fan to get to that short bolt on the bottom. Thanks for the great walkthrough!

@syberr3135 2 года назад

Another informative video from mr Fritz thanks bro!!!

@FritzRamos 2 года назад

Thanks for the support, glad you found it helpful

@bigredbeanie3310 2 года назад

Amazing video again and the bolt torque visuals are the best, maybe Valve cover gasket next? 👀

@FritzRamos 2 года назад

Thanks! I've been trying a few graphics to see what people like. Looks like I'll be sticking with this set. As far as the valve cover goes, once it starts to show signs of wear we'll make a video. For now it's holding up fine 🤞

@skyscout11223 Год назад

Can you do a video on B38/48/58 series engine oil filter housing change? There is an upgraded aluminum set and there might be a lot of folks interested. You're the best! Thanks a lot!

@KzLollapalooza Год назад

Thanks for your video!

@tonyvega2563 7 месяцев назад

best one on this I've seen!

@jg_media9 2 года назад

Great video my friend! Super detailed and informative 👍

@FritzRamos 2 года назад

Thanks. I see you upgraded 👍

@jg_media9 2 года назад

@@FritzRamos mosselman thermostat from Kies for the win 🔥

@josephnegron5830 2 года назад

I watch your videos often and I have a 2011 x3 35i however I was having several overheating issues. I done the thermostat which looked good when pulled out. Then I did the radiator and water pump. It’s doesn’t overheat at all but runs like around 240* never over just very concerned still around that temperature

@marshallgoldberg8376 2 года назад

Test the water pump. Make sure coolant is flowing. Make sure your radiator fan is operating.

@brucito56 2 года назад

Hi Fritz. I am getting ready to do an oil pan gasket replacement on this same car, 2014 BMW X3, N55 3.0 liter and I would like to know which Bolts are NOT included in the bolt replacement kit commonly used for the repair. My understanding is that 2 additional bolts are needed, but which ones?

@Quixoteyou1 2 месяца назад

Using the 8mm on the small bolt stripped the head. It is torx same as the others on the 2014 x3

@hyde_official 2 года назад

nice. for the filter housing, wouldn't have been advantageous to replace it with a much more nicer looking one like that I have in my N20? than it would have been easier to work on next time when doing oil change etc. just a thought.

@FritzRamos 2 года назад

Thanks man! I agree with you, but if cost is a major factor then this is the way to go. This also isn't my car. 😅 Always good to hear from you my friend, wishing you all the best for the holidays. 🎄

@hyde_official 2 года назад

@@FritzRamos Happy holidays to you as well, my friends.

@alienpredator7886 2 года назад

Grateful video lm have a question do you need to purge a antifreeze system l see videos if do you not due damage de engine damage l have a 2014 BMW X5 xdrive35i any help my thanks

@FritzRamos 2 года назад

It's not a bad idea and doesn't hurt even if you don't 'need' it.

@detta1413 2 года назад

You need to prime to engine as well

@jameswan670 Год назад

That 8mm rachet for bottom bolt is just normal 8mm socket or E socket?

@leviwilbert9588 8 месяцев назад

Do you not replace the intake manifold gaskets? I'd think if you're breaking that seal it'd be a good idea to reapply a new one.

@jkoljonen 2 года назад

Nice video, but unfortunately you missed the extremely important step of priming the oil pump and oil supply system. BMW has instructions for this. With no priming, there is an increased risk of total engine failure after startup.

@FritzRamos 2 года назад

Thanks for pointing that out. In this case (reusing the filter and no oil change) adding some oil through the housing and allowing it to pass through would be fine. You could also pull the fuse and allow it to prime.

@jkoljonen 2 года назад

@@FritzRamos Perhaps it would be fine. However, I would still follow BMW's service bulletin on this matter. It suggests that priming is required whenever oil supply circuit is interrupted. BMW suggests to remove fuel injector connectors, then run the starter for 3x 10 seconds with 20 second pauses in between.

@FritzRamos 2 года назад

@@jkoljonen All good points. As you said, you could pull the fuel injector connection in place of the fuse that controls them.

@davidhoang4241 2 года назад

Not needed in this case. Otherwise, you'll be doing it every time you do an oil change. If you're replacing main components (pump, housing, cooler, etc.) then it's advised to follow the correct procedure since replacement parts are completely dry. Keep in mind that the oil pump in this case is already "primed", more so since the oil was never completely drained. Anyways, to each their own.

@keviin20061 Год назад

@David Hoang I was thinking the same thing. It shouldn't need to be prime every time all you filter is placed. That is not major part replacement that has large amounts of oil loss

@ElliutN 9 месяцев назад

Did have to drain the oil tondo this job? TIA

@lytleric 2 года назад

Do the bolts need to be replaced with new ones (i.e. are they a one-time use), or can they be reused? I see some gasket kits that come with new bolts, so I am wonder if they are single use. I have this same leaky gasket issue with my N55 so I am about to order parts and want to make sure I get everything I need. Thanks for the detailed walk-through.

@Devosent Год назад

Yes you will have to buy new bolts and torque them to spec, BE CAREFUL with unscrewing and screwing the bottom screw, I've accidentally stripped the threading into the housing and so have other people. Don't forget to prime the engine afterwards once the work is complete.

@4touchdowns1game29 6 месяцев назад

no unless the n55 has different bolts. My kit for the n52 came with bolts so I changed them but both sets weren't aluminum bolts so they should be good.

@stevew145 2 года назад

Take extra care not to drop nuts when removing intake manifold... They fall into the shadow realm, never to be seen again and are a very odd M7 pitch, so (at least where I live) no one carries them!

@FritzRamos 2 года назад

The shadow realm! 🤣

@MotorenMatze Год назад

Hey Fritz, I have to replace my oil filter housing gasket, too. Is it recommended to replace the intake manifold gaskets as well?

@popeyes7376 Год назад

@Scotford_Maconochie Год назад

If you remove your intake manifold completely then have your valves walnut blasted then replace all 6 gaskets.

@vguitarman Год назад

Okay, actual question: Would it be worth removing the fan shroud for this?

@FritzRamos Год назад

I wouldn't

@johnnyartiga3028 Год назад

any tips for doing this on an N55 135i I don’t think the oil cooler is attached to the housing and would like to know if I need to do anything differently

@johnnyartiga3028 Год назад

not one that looks like yours at least

@FritzRamos Год назад

Here's another example ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bPcgCiaHFPg.html

@ademc8872 2 года назад

You should’ve included the priming of the oil circuit. Great video nonetheless.

@FritzRamos 2 года назад

Will do in the next video. Thanks

@marco711509 2 года назад

So it’s recommended that you drain all the oil?

@FritzRamos 2 года назад

You don't have to. It wasn't in this video. If you do, just prime it from the oil filter housing

@ronhuppert7505 Год назад

I have a 2013 535i. I removed 2 bolts and 4 nuts from the intake manifold and it won't budge. What am I missing?

@tonyvega2563 7 месяцев назад

another nut? in multiple vids I have seen a count of 7 total.

@davidmontalvo6560 Год назад

HOW ABOUT GETTING THE AIR OUT OF THE SYSTEM? SHOULDN'T THAT PROCESS BE DONE ALSO

@MotorenMatze Год назад

7:59 The screws are 11mm and not 10mm

@Scotford_Maconochie Год назад

Once you've done this. Clean your MAF sensor and replace the oil filter.

@vguitarman Год назад

@0.29 is that a brick of cocaine? I called FCP Euro and they don't have any in stock. Can I use meth instead?

@FritzRamos Год назад

😏

@muzkhan1361 Год назад

For oil priming, you can just remove the fuel pump fuse per the updated BMW TSB static.nhtsa.gov/odi/tsbs/2016/MC-10151166-9999.pdf

@jimmyle1432 Год назад

I get quote part and labor $450 for oil filter gasket

@thorshammer81 2 года назад

Crazy how this job would be a $1000+ at a shop

@FritzRamos 2 года назад

1000! Really?!

@Dynamics831 2 года назад

$1,200 at the dealer

@Dynamics831 2 года назад

60k mile service $2,200

@ismail9693 2 года назад

I was quoted $1,600... smh

@slidewayskrew Год назад

Surely this is the same on most n55s

@FritzRamos Год назад

Just a slight difference in intake and hose connections ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bPcgCiaHFPg.html

@cleanerdetailsllc7789 Год назад

just paid $775.24 parts and labor. 2012 BMW 528I

@FritzRamos Год назад

Did you upgrade the thermostat?

@cleanerdetailsllc7789 Год назад

@@FritzRamos engine air filter adapter plus the cooler seal not sure the thermostat wasn't on the bill. I got it done at a local independent in Denver called Auto Imports