Remove a Peugeot Citroen Vauxhall locking wheel nut without a key. No Key no Problem

Подписаться 51

Просмотров 11 тыс.

50% 1

How to remove a Spinning Peugeot, Citroen, Vauxhall locking wheel nut without a key by employing 3 different ways.
1. Spot weld method.
2. Split the spinning collar method.
3.Impact socket method.
For more info on removing these type of locking wheel nuts go to
www.wheelrepairs.co

Авто/Мото

Опубликовано:

5 мар 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@tenfootvoyager Год назад

Many thanks for the impact socket idea. Got 3 off my Citroen C4GP but forth was being a sod and must have tapped it back rendering it useless. Had me completely baffled until I saw your video. Regards John.

@wheelrepairs 11 месяцев назад

Glad it helped!

@wheelrepairs Год назад

I have several sets of reverse thread removers..they are all thin walled. The prob with halfords type is that they only fit car wheels that have lots of room where the bolt / nut sits because the walls are so thick. Plus its a two socket pack..so only two sizes! But its a real go to if you have lots if room in your rim and its the correct diameter for your locking wheel nut.Positive point with these halfords is that they will not crack! Bad news is the halfords reverse thread will not fit these type of locking wheel nuts at all. You have to physically remove the spinning collar to fit a very small reverse thread. Halfords are way to big for these.

@mrlister2000 5 месяцев назад

The method you mentioned around 4 minutes, I have tried this and the centre twisted off, leaving just the bottom of the nut, and impossible to then get off

@wheelrepairs 3 месяца назад

I never had that happen tbh, but i can imagine that coukd happen if it was totally over torqued. If that happened it would be pretty easy to get off if you have a small welder. In fact i will grind one down flat and show a video of how to weld one

@paulagill1577 6 месяцев назад

Any idea anyone how to get part sheared bolt garage broke out of the locking nut

@wheelrepairs 6 месяцев назад

Did you get it out?

@paulagill1577 6 месяцев назад

@wheelrepairs no there no way to get it out

@PhilTheProf Год назад

Please buy a small camera holder or tripod, this will free up both your hands.

@wheelrepairs 11 месяцев назад

Good idea..will get one!

@victorterry 2 месяца назад

What size socket

@wheelrepairs 29 дней назад

I use 17 or 18 mm on these

@adrianedwards6911 Год назад

Is a reverse locking nut remover useless for this job ?

@wheelrepairs Год назад

The reverse thread socket will not work with these type of locking wheel nuts as the spinning collar makes the threaded socket useless. You would have to remove the collar first and then purchase a very small diameter reverse thread to fit over the center stud, or fit a standard 6 sided small socket.

@adrianedwards6911 Год назад

@@wheelrepairs thanks for your response. And excuse my ignorance I did watch your video from start to finish great content and very informative keep up the good work 👍🏽

@wheelrepairs Год назад

@@adrianedwards6911 All good, please feel free to drop me a comment or email if you have any problems removing yours.

@wheelrepairs 11 месяцев назад

If it has a spinning collar, this reverse thread socket will not work.

@seemaab 4 месяца назад

@@wheelrepairsmy collar came off and I can’t get the socket off. I tried a 12/13mm socket but it doesn’t work.

@markm49 8 месяцев назад

I drilled out the centre and used a screw remover to undo the bolt. Hard work but worked fine. Stupid design.

@wheelrepairs 8 месяцев назад

Yes.. ive seen a couple of people do that.. the center stub is not very wide so you have to be careful. Yes daft design, i had to weld one out today after AA had recessed it!