Ryobi Pressure Washer Repair - How to Replace the Pump

Подписаться 71 тыс.

Просмотров 106 тыс.

50% 1

Need help replacing the Pump (Part # 308653054) in your Ryobi Pressure Washer? Watch this how-to video with simple, step-by-step instructions for a successful DIY repair.
Don’t already have this part? You can pick up an authentic OEM part sourced directly from the original manufacturer here:
www.fix.com/parts/pressure-wa...
Fix Part Number: FIX9938329
OEM Part Number: 308653054
Why you might need to replace the Pump:
1. Stuck Unloader Valve
2. Damaged or Melted Valves
The information in this video is specific to Ryobi Pressure Washers. To find an Pump specific to your model Pressure Washer, or to use our helpful model number locator, visit www.fix.com
Not what you’re looking for? For more Pressure Washer repair help click here: www.fix.com/parts/power-tool/...
For more helpful Pressure Washer Repair videos, you can browse through the Power Tool Repair playlist on our RU-vid channel: • Makita Angle Grinder R...
Fix.com is committed to providing you with high-quality parts, quickly and easily. Find out more about our fast shipping and interactive customer service on our website.
www.fix.com/
Stay safe during your repair! Be sure to check www.fix.com/safety/ for proper safety procedures before you begin. Use of this video is at your own risk, without liability to Fix.com.
Connect With Us!
/ fixdotcom
/ fixdotcom
plus.google.com/+fixdotcom
/ fix.com
If you found this video helpful, give us a thumbs-up, and subscribe to this channel for more useful repair videos! Don’t forget to leave us a question or comment below, and our customer service representatives will be happy to help!

Хобби

Опубликовано:

22 апр 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 78

@abelvillarreal5383 4 года назад

Awesome video. Thank you for the content.

@abissvc 3 года назад

Thank you for sharing!!! Great help

@ttwyman7751 2 года назад

Very good video. Extremely detailed and at a good pace.

@michaelwelker3595 3 года назад

Great video!

@giopirmisashvili5514 5 месяцев назад

Thank you

@angeloamica5838 Год назад

Thanks for your video. I have a Ryobi 2900 psi 2.3 gpm. Oil is leaking from the bottom. Where can I get washer seals?

@jonbabtis8666 3 года назад

Hi just bought a ryobi 3000 psi pressure washer, im wondering if theres in the pump and where is the location to add it? Thank you

@MrEvanBacon 8 месяцев назад

Can you put a faster pump on this model of pressure washer?

@rpmazzella 3 месяца назад

Replaced the pumpand the unloader valve and still low pressure, any suggestions

@lalo2641 Месяц назад

Thanks

@stephenstudzinski6651 2 года назад

Where is the best place to order a new pump for this Ryobi 190?

@lancekmurray 3 года назад

Wow, perfect. I found mine has a crack in it today. Been a couple of years since I last run it, but I know I prepared it properly for storage. Oh, well, at least it will be more economical if I fix it myself. This will be the 2nd time I've had this replace (1st for hard water deposits). Wish these things were designed to be a little more idiot proof (not accumulate hard water deposits, freeze plug, whatever).

@wildwoodtop 2 года назад

Did any oil spill from the crack

@lancekmurray 2 года назад

@@wildwoodtop No oil, just loss of water pressure.

@marlon5656 8 месяцев назад

Would a bad pump cause it to turn off once the trigger is pulled. It idles but it turns off once I pull the trigger.

@anthonyedmond2538 3 года назад

Spray nozzle water flow adjuster repair

@ourgreenworldhorizonmediae2071 2 месяца назад

My idler assem only has a retainer clip or staple and doesn't have a nut for loosening like the one in this video

@christianmayensv Год назад

I need that water pump. Where I can Get that?

@user-qo5kd4dt9j 11 месяцев назад

Where do you drain the oil and refill the oil in the water pressure pump 5:58

@quintinvaladez8663 Год назад

What is the part # on the pump?

@CommanderSix 2 года назад

What contraption is on the opposite end of the thermal relief? The black circular thing? My dad needs to replace it.

@FixDotCom 2 года назад

That is the garden hose coupler. Look up your pump using the pressure washers model number. Some manufacturers offer the coupler as a replacement part, others offer very few parts and you will need to replace the pump. -Mark

@54Bluenote 3 года назад

Do you need to adjust the pressure on the new pump?

@knightridert71 3 года назад

@robertmabante227 Год назад

What is the pump number

@juanjirau8994 3 года назад

I have the same pressure washer, the issue is that sometimes when I press the trigger of the pressure hose nozzle it don’t response !!

@donschlonski2936 3 месяца назад

Mine is doing that right now and I'm looking to replace the pump

@samsydneygarrote5976 2 года назад

I have a hard t I me taking off the pump? Any ideas ? Took off the bolts already

@Pingaheimer 3 месяца назад

spray the bolt holes with some wd-40 or your rust penetrant of choice and let it sit overnight.

@carmanwright2889 8 месяцев назад

What is the best way to try and free a stuck unloader valve?

@Pingaheimer 3 месяца назад

I was having a hell of a time with mine and sprayed it with some wd-40 and let if sit for a few hours. Came out with pretty easy prying with a flat head screwdriver after t hat.

@truongtran1305 3 года назад

Mine doesn’t fall off after all the bolts are undone. It’s pretty stuck. Am I missing something here?

@bigbomb5904 Год назад

Mine is the same, did you figure it out yet?

@jaymartinez6250 Год назад

@bigbomb5904 2:02 you can see a little metal bar sticking out from the bottom of the motor on top. Since he has probably already taken his off once or twice before this video it comes out freely. Yours may not since it's the first time removing your pump more than likely. That little metal bar is probably stuck in there a little.

@jaymartinez6250 Год назад

His hardware is all brand new looking as well

@paulverrilli4899 Месяц назад

It's probably due to corrosion. Use a penetrant like PB Blaster on the shaft, give it a while to set in (could be minutes or hours depending how bad) and good old fashioned bludgeoning with a hammer to free it since you're not keeping the pump, presumably. Then, I would strongly recommend cleaning the shaft and key and applying a lubricant to prevent corrosion next time around. Careful not to beat on the thermal relief he's instructing you to transfer to the new pump or you'll be buying that too!

@Elsanta666 4 года назад

Can i run hot water through this pumps

@kennethgilbertdds7249 4 года назад

No this one. The hose is cold only. Needs a better hose.

@aamador50 4 года назад

Hi. Do the pumps use any oil??

@kt550 4 года назад

Any update on this?

@aamador50 4 года назад

No update sorry

@kt550 4 года назад

aamador50 manual says nothing. I don’t think they are serviceable. Only thing I’ve seen are people tapping drain plugs into them. Seems like a “lifetime” part, once pump goes its time for new washer or pump assembly

@kennethgilbertdds7249 4 года назад

There is a spray to use if you plan to store the pump like over winter. This is sprayed backwards up the water hose connection port/fitting. Otherwise no. The motor requires oil of course.

@jesusdanielberistainlopez1244 4 года назад

How chance The oil?

@kaostheory1370 4 года назад

Some pumps that don't have a oil plug to drain, you have to use a transfer pump to pump out the old oil. Harbor freight have those for 4.99$

@kaostheory1370 5 лет назад

Any ideas on removing the old pump that is rusted/siezed onto the engine shaft on this particular setup. I've soaked it in pb blaster, used a pry bar, rubber mallet, heated the shaft, even hooked a chain around it with a bottle jack but to no avail... please put me out of my misery lol

@suppaman12 5 лет назад

kaostheory1370 sell it as is and get another. It sounds like the problem will be more severe than just the pump

@bgdavidcryptonite4158 4 года назад

wedges between the motor and pump..is how i got mine off..was a pain...

@vargazzdlh 4 года назад

Same problem here, I'm think in cut off the old pump with angle grind😡🤬🤞

@kaostheory1370 4 года назад

@@vargazzdlh so that's what worked. I had a friend take an air hammer and angle grinder to it and after a while finally got it to release. Just make sure that you dont damage the motor shaft. Cut off as much of the pump as you can until you have enough room to get the grinder on it

@AJKlos 4 года назад

I even took the whole pump apart and still can’t get this pump off. This dude slid that thing off like

@PantherSpawn 4 года назад

My ryobi has the idle down throttle.. The replacement pump does not.. Can I swap my old throttle to the new pump? If so, how?

@adamlombardo3490 4 года назад

Paul did you figure out how to remove idle down throttle?

@PantherSpawn 4 года назад

@@adamlombardo3490 I did not. I have not had time to look at it. Likely going to send the replacement back and get another one with idle down assembled.

@vargazzdlh 4 года назад

You can lock tbe mechanism to run in high rpm but you will have a high fuel consum e high noise all the time

@steveale0711 Месяц назад

Just move the spring on the idle down to a small hole under the on/off switch plate. You won’t have idle down it will run at speed all times but won’t matter.

@dustinkruize6428 3 месяца назад

Imagine replacing a new pump with a brand new pump and a brand new never used pressure washer. Yes everything is made easy

@chrishennek5900 4 года назад

I am replacing the pump on my Ryobi v190 3100 PSI pressure washer. The Idle down cable looks very different from the one in your video ; instead of a screw to hold it in it has a U shaped clip which I removed but the cable does not seem to want to pull out please help.

@taddhoward2113 4 года назад

Im with you. did you figure it out?

@taddhoward2113 4 года назад

ha, just got it. Put a pair vice grips on it. It has two seals inside holding it in. It pulls out

@danhead8795 4 года назад

@@taddhoward2113 any tips? I have been fighting with mine for about a day and cannot get it out. Also, how did you get it into the new pump

@bobbydempsey8044 Год назад

I have the same problem how do you get the throttle cable out

@bobbydempsey8044 Год назад

I have the same problem How do you get the idol cable out

@tundrablue05 4 года назад

How do you know the pump is bad? Mine runs fine till you add water pressure... I figure it may be the pump

@FloRuski 4 года назад

Fellow youtuber lol, I've heard a lot of the time it is an unloader issue. If the pump has the water turned on and it stalls out the engine unless the trigger is pulled on the gun then the unloader may be stuck.

@jakegetz6636 4 года назад

@@FloRuski do you have any clue how to remove the unloader valve on these ryobi pressure washers? because i tried everything and can not get it out, it should just pop out with a screwdriver but it wont.

@FloRuski 4 года назад

Jake Getz I found that heating up the aluminum to pretty hot temps with a torch made it easy to pop out. Mine was stuck as well, hope it helps man.

@knightridert71 3 года назад

@@jakegetz6636 my ryobi 3100 unloader is the same way can not get it to come out at all with out busting the freaking pump case it is so stuck ,,and i have herd several of these ryobi's do this and i had to spend $150 to get a hole new pump . i even heated it with a torch but that could mess up the rubber seals this thing pisses me off

@Pingaheimer 3 месяца назад

@@knightridert71 the o-rings are cheap.... it should be easy to remove once you get some rust penetrant like wd-40 in there and let that do it's thing for a few hours.

@rpmazzella 4 месяца назад

Nice job. What does your wife have to say about you changing a pump in a white drees shirt?