No video :(

Stihl 029 Super Chainsaw Assembly Part 3

Подписаться 596

Просмотров 13 тыс.

50% 1

Finishing up this Stihl chainsaw!
Note that the washer is missing under the clutch assembly that will say top. Do not forget it!
Please leave any comments or questions below . Remember to like and subscribe!
Part #s
9639 003 1743 - Crankshaft Seals
1127 020 1210 - Piston & Cylinder 46mm
1127 358 7703 - Fuel Hose
0000 350 3500 - Fuel Filter
1127 640 3204 - Oil Pump
1125 640 7100 - Worm Gear
9512 933 2260 - Needle Bearing 10x13x10mm
1127 792 9100 Hand Guard
9460 624 0400 - E Clip for Strap
1127 141 8600 - Impulse Hose
0000 930 2212 - Pull Rope
1127 120 0650 - Carburetor HD 19D
1127 120 0604 - Carburetor HD 18D
0783 830 2000 - Dirko HT Red
Part numbers are subject to change without notice.
DISCLAIMER
LubeTube is only sharing tips and tricks to aid in repairs or services herein.
LubeTube and associated parties are not liable for any damages of any kind, whether that be public, private, personal, and so on, while repairs or services being carried out by said individual(s). Please accomplish all repairs and services safely at your own risk.

Опубликовано:

26 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@royvazquez1244 Год назад

A couple of glitches with your microphone, but I was able to follow along, thanks for the video

@lubetube. Год назад

Yea the GoPro loves to switch microphone location by itself. I've since got the Media Mod. It also turns off a lot due to overheating.

@treborterb 4 месяца назад

I have an 029 and was wondering...doesn't that rubber grommet that you are fighting to remove from the orange plastic outer cover have a torx bolt through the center so you can just remove it without fighting it ?

@johnclarke6647 Год назад

No new cylinder and piston will have much compression at first. Sometimes they are almost impossible to even start. They need about 4-5 hot and cold cycles to develop enough compression to even start, reliably. This is why I crank them up and let them idle for 15 minutes, initially, before shutting them off. I do this about four times before I even put them in the wood and limit their use for the first few tanks to intermittent use on small wood.

@fishon7301 11 месяцев назад

My spark plug boot popped off the wire somehow. Am I supposed to pop out the plug wire inside the boot, then reattach it to the wire and then get that wire to slide back inside the boot? It looks too big to fit through the hole in the boot. The mechanism for the plug wire to reattach to the black coil wire with a simple hole in the side of the insulation seems like a really bad design. Any better ideas?

@johnclarke6647 Год назад

On all the AV rubber parts it is a good idea to spray them with a soapy water solution. This helps them go in, easily. The 029, 290 and 291 are basically the same saws and are a B to work on. I will not rebuild one of these saws if I can get out of it. An 029 Super was the first saw that I ever rebuilt. However, I learned a lot and if you can rebuild an 029 you can rebuild any Stihl saw. I smoked the flywheel key because I did not know that you have to degrease both the flywheel and the crank before you put the flywheel on. Any oil or grease will shear the flywheel key. I also learned how to pull the intake boot through the rear housing. It ran fine and is still in operation the last I heard. I put the original 46mm cylinder and piston on it, aftermarket of course.

@lubetube. Год назад

Yea man you find tricks along the way. I probably do a few a year. As long as you take care of them they tend to last a long time. Let face it, who is actually cleaning the saw off after each use😁?

@rickbailey7606 Год назад

Great video!!

@tedneitzel Год назад

What was the parts used for future reference thanks?

@lubetube. Год назад

Sure ill put them in the description. Honestly, I need to do it anyways. Thanks.

@johnclarke6647 Год назад

You need a richer H jet. Hear it stumble in the cut? It should maintain the same rpm throughout the cut if it is tuned properly. I hear it begging for more gas - feed me, feed m, feed me.

@lubetube. Год назад

WIll do. I'll give her the full juice!