Тёмный

VW Polo 1.4 cambelt (timing belt) change - "How to" 

VWGenuineParts
Подписаться 36 тыс.
Просмотров 692 тыс.
50% 1

How to change a cambelt on a Volkswagen Polo 1.4 with BBY engine - step by step guide.
Our "How to" information is for guidance only. Do not attempt a repair if you are not appropriately trained or do not have the correct tools or equipment to conduct a repair safely. Some models will differ from this guide.
VWGenuineParts.co.uk takes no responsibility and cannot be held accountable for any loss, injury or damage however caused. No claim can be made against us for loss of earnings, inconvenience or any other incurred expenses. Unless otherwise stated, all contents are copyright ©

Опубликовано:

 

5 янв 2012

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 7   
@mrrichardrichie
@mrrichardrichie 11 лет назад
before you put on the MAIN TIMING BELT, did you position the tentioner @ 10 oclock position? according to a haynes illustration , the tentioner is turned to 10 0clock position AND THEN THE BELT IS REFITED AND TENTIONED . IS this recommended?
@mrrichardrichie
@mrrichardrichie 11 лет назад
one last question. the question is about the small secondary belt. the last item the small belt goes over is the tentioner? i start from the inlet cam from the top then the outlet cam and then finally the bottom?or is it better to put the belt starting from the tensioner side?
@mrrichardrichie
@mrrichardrichie 11 лет назад
greetings . i am working on the same engine and would appreciate advice. after i takoff the secondary and primary belt, i will TURN THE crankshaft sprocket 6 teeth back so that if both cams move there will be no DANGER. WHEN i put the SECONDARY small belt , is it ALRIGHT FOR me to keep BOTH CAMS locked and keep CRANK 6 teeth away 4from tdc? i will turn CRANK BACK TO TDC when i put on the primary belt, but is it alirght to keep it 6 teeth back when PUTTING ON the secondary belt? thanks
@hammerjohnston
@hammerjohnston 11 лет назад
Hi, I have the 1.4 BBY engine in my Audi A2 and I need to change the camshaft position sensor, would you be able to tell me where it is?
@peterclark5510
@peterclark5510 10 лет назад
what does the word carrier mean on a car engine thanks for any help peter
@mrrichardrichie
@mrrichardrichie 11 лет назад
before i put on the primary belt , i have been told to make sure that tentioner plate is pointing at 10 oclock position. i will START at the water pump, crank, idler, CAM and then end @ the secondary idler near the water pump.
@xyrljay
@xyrljay 11 лет назад
how much the cost of timing belt set
Далее
How to Tell if Your Car Needs a New Timing Belt
3:34
When A Gang Leader Confronted Muhammad Ali
11:43
Просмотров 4,9 млн
IQ Level: 10000
00:10
Просмотров 10 млн
Vw Polo Vivo Bent Valves Part 4   Assembly   Start
11:45
Просмотров 102 тыс.
5 signs of a worn timing belt | AUTODOC tips
6:49
Просмотров 95 тыс.
[EN] Watch and Work - VW Lupo 1.4 16 V
6:15
Просмотров 116 тыс.
Don't buy a Polo without watching this!
13:19
Просмотров 75 тыс.
Polo 1.6 cambelt replacement
8:23
Просмотров 32 тыс.
IQ Level: 10000
00:10
Просмотров 10 млн