Zero Gap Any Clippers in 4 Minutes | Tip #15 | Barber Equipment 

Saving Money, thanks for that comment. My pleasure. Be sure to share!

Ismael Castillo, I appreciate that! 👍🏼

I don't think you can do it the same way with the T Blade Taper Clippers a Lil Different

The music is annoying

VIC CAMPOS, thanks! If I understood you correctly, then yes, that sounds right

sunil dutt, awesome. Thanks for commenting

parallel jinx, my pleasure

My pleasure

All good but if your new get the Magic

boulala21 yes you can I have the same clipper as you. You can 0 gap them

@@NighmareRS oh sweet, do you know if I need different screws? as that's what I read somewhere else. Cheers

Thanks! Good question: I briefly mention at the end that it's for precision, but a better reason is that if you're ever using the clippers without any blades, you'll be able to get a really short cut. So if you're using the clippers in the short setting without any guards, it'll be as close to a zero as you can get it. Does that make sense?

Tips for Clips - Haircutting can it be used as a trimmer ? For beards

Saliba R, to lighten up a beard? Yes

@@TipsforClips do you need to zero gap if using 00000

@@TipsforClips hey bro i just bought hair clipper and i always cut with guard on but i dont want that when i remove guard it cuts so bad how can i get rid of it

Janet Bullock, really glad to hear that, thanks for your comment

U lazy

@@marjonyoung305 Ikr, literally a one minute job haha.

Tighten, oil, and straighten the blades

Did you figure it out?

I have the same problem also

Check your blades to see if the cutter blade is higher than the guard blade.

Lol. I feel you bro. You gotta adjust them. Then try them. Then adjust and try them again and again until you get them just right. It can be a pain

Lol @ all this little cuts all around my head. 😂😂

I've zero gapped mine too and am getting cuts, sore patches and old skin being taken off

@@DanielGreen07 I had to readjust them a few times. Just a little bit at a time though. You might not get them to cut as close to the skin, but at least you won't skin yourself alive either.

@@joej3900 I've adjusted them as best as I can, they ll do til I can get a pair that give that smooth skin cut 👍

josua su, thanks. You can use clipper spray sold at beauty supply stores

The screw on the lever only tightens or loosens the resistance of the lever. It doesn’t allow for adjusting the position of the blades.

@Sheriff. 0 gapping is for fading, it helps with removing leaving fades lines for better blends. For beard, I would use a trim liner, they give a crispier lines and easier to handle.

Viktor H, I’ve never tried the Icon. You can certainly zero gap Wahl clippers, but if you want to shave your face, you will not get a clean shave as you would with a blade. Zero with clippers is not as sharp as trimmers or blades

Thank You! My goal on my face isn't a totally smooth skin so it'll good for me if it is adjustable to a near zero gap as You told. My doubt was only about that Icon's adjustability as in the video I'v seen.

@@TipsforClips Wahl Cordless Magic Clip gets excellent ratings even from competent barbers. But you will have to buy both a trimmer and a shaver. A trimmer would probably cause too many nicks and scars. My notes below may help: F: Zero-Gap Any Clippers in 4 mins - Tip #15 - Barber - Best so far!!! ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-YKJmk_hxD-o.html 1. Excellent, superb video, but didn't properly explain which; A. blade was on the bottom (the one with the screws in it), and B. that the forward (facing the front of the clipper) lever's position closes the teeth. C. Oil the clipper before and after use. 2. Should probably holding the clipper upside down Whilst removing the loose hairs A. Instead of brushing some of the loose hairs inside the clipper. G: How to zero gap Wahl Cordless Magic clips - How to test if the zero gap is correct, but poor close-up ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-FPtAw6KYoec.html H: How to zero gap your Wahl clippers the easy way - NB! Oiling Section is good ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-dxeqj0M3QR4.html

123 654 Nope, won’t work because the two holes in the blade and the two screws holding the blade have the same diameter. When I loosen the screws the blade is still fixed. It can only be moved when the screws have been removed. Maybe they have changed it with the model I have (Wahl Super Taper Cordless). I have now used two different screws to make it work like you have described. Thanks.

Scardrewpro, zero gapping helps you cut shorter, so it’s good for a balding haircut, though you’ll need something other than just clippers to entirely bald it out. It also helps with precision

It appears that most excellent clippers can cut hair to 0.8 mm but if you have a good shaver than it should be able to cut the hair from 0.8 mm to 0 mm safely.

So for super low, balding haircut to get the look you need clippers and trimmers together? You can’t just use trimmers, like T Outliners by themselves, if your hair is already short and you want it super close? Thanks

Same question I have

Noe Glv, Andis Speedmasters I, pivot motor

Revolution97, thanks a lot for the compliment! I have both of those videos out. If you can't find them, let me know and I'll paste the links in a comment here

Sorry, I'm not sure

Doubt it! This is because the same power would be outputted to the motor. The motor is the main thing that generates the heat. The best type of quality motor arguably is the Rotary motor. besides the quality of the hair clipper, obviously.

Nope, the trimmer will still get the same input voltage no matter how much you upgrade the power cord, the cord included with it is designed to be thick enough of wire to carry the power. Unless your cord is getting hot to the touch or has serious damage such as exposed copper wire, there is no reason to replace it. You also risk voiding the warranty. Only thing I can think of is make sure the blades are oiled and that the machine is not clogged with hair and debris, if you're mechanically minded lightly adding oil the to motor bearings may help it, but I doubt this is the issue. (This is advice for everyone)

trueGrizzlesFAN22, nice! Thanks for sharing

@@TipsforClips i only used the wahl clippers on me. i know there are better clippers but my brother introduce me to the chrome pro and i used the adjustable gap clippers to shave my facial hair. I am so please.. Your video save me TIME AND Money ... thanks again

Idris Ertem, yes 👍🏼

It's the big blade bro. If the little one is sticking out farther, you will cut yourself or your client.