I've ordered this part for my car and I keep getting a shorter sway bar link. I have know idea what to do. It's for passenger side front and it's a 4 matic. What am I doing wrong?
Your car interior is just like mine. Can you recommend a site where I could get accessories for mine? Like head rests, window control buttons, back ventilation cover,camera, android infotainment, etc
I hope you see this today. I’m working on a 2012 mini cooper and installing a wireless backup camera the signal goes out when I put it in reverse. I tapped into the wiring like you showed but it still doesn’t work. It seems my reverse signal starts pulsing when I shift into reverse. Any thoughts? Do I need a diode of some sort?
Hi Raymond, Can you make a vid on how to connect the Foxlox on the convertible which requires passenger connection and repining the foxlox connector white and grey wires for it to work.
Thanks, I successfully replaced my links on 2015 e350. Different parts but similar procedures. It certainly was tough finding a torx driver to fit the lower bolt and I wasn't able to fit ny torque wrench on the top or bottom so just made it good and tight.
I just broke a T40 torx bit from Harbor Freight on the front drivers side of a 2011 E350 4matic. How did you get that torx bit off so easy?! Did you use any lubricant? I just stopped the job and I'm going to start again when I have more time to commit to it. Also, Lemforder makes a lot of suspension parts for German vehicles. My Audi Q7, X5 & 7 series all have Lemforder suspension parts, the BMW logo is just ground off, thats how FCP Euro can sell them for so cheap. I always replace my sway bar links with Lemforder parts. Great video!
So if you dont have that pop up display, the backup camera wont connect? I have an 08 E350 and im having trouble getting info on whether or not this can be done with the factory head unit (has no pop up display)
@RaymondUrias can i install the C1-650x (Coaxial) version of these instead of the ones you installed on w203 front doors? if so do i keep the OEM tweeters? or remove them?
I gotta say this is probably the best video for that job. a few years back i ordered the same parts for my 90 droptop fox red with white top and went off lmrs video and way to go and was a horrible unfinished project until now. you have skills man keep posting vids. thanks
Ok I listened to you give the pin out on the aftermarket female clip you said front driver front positive driver front negative then at the end you have written driver front positive passenger front negative which is it
Thank you very much - my wife dropped 2 diamond rings into the seatbelt hole of the 2023 CLS and successfully retrieved them within 5 min in the same way. The dealer wanted to charge us 300++ dollars! 😀😆😁🙏
What no Hulk Squeeze prompt on the crimping? 😅 Seriously though, very informative. I just learned how to use wire taps(I have so many in my new set). Can't wait to try them out. Much Thanks for the info. 👍🏼
Thank you very much for this deteailed Video from germany. I hope i can get all parts i need because lmr doesnt send overseas....only CJ Pony. Best regards! Many Thanks
Can you tell me, which ntg Comand you got? i got a 2009 C-Class NTG Comand 4.0 and i havent this engineering Mode.....I press phone off, one and the hash key at the same time, nothing happens...Is there anything else that needs to be coded?
i’m the only one after i did all the fit of the revers camera i did and the relay and after i turn my engine on i put R and still not clear image or sometimes is black but i can see the gauge lines what can be wrong guys i got almost 12v i check it
Here is just an additional note in dealing with the removal of the top rear seat cushion. The factory design makes it hard to get to the bolts holding that cushion in place, both for removal and reinstall. The last time I remove the seats, I used perforated metal pipe strapping and created an extension for both the seat back and the flange that the seat attaches to. I then bolted those extensions to the flange and to the seat, then installed the seat and bolted the extensions together. It took about 30 minutes to do the initial set up, but now removing the seat bolts is about a one minute process! 😂
