Common Problem HONDA GCV 190 engine. HARD to PULL . HARD to START FIX Pressure Washer ROCKER ARM

Подписаться 61 тыс.

Просмотров 181 тыс.

50% 1

Jeff's Little Engine Service shows you HOW TO fix a common problem on a HONDA model GCV 190 pressure washer engine that is HARD to PULL HARD to START . Won't wont start REPLACE Broken EXHAUST ROCKER ARM from stuck valve was the issue. ADJUST VALVES remove Repair replace specs specifications procedure valve lash intake Same as on lawnmower water sprayer john deere mtd poulan briggs too much compression where what when does parts numbers choke take off on which way procedure
Copyright 2020 Jeff's Little Engine Service
Donations are greatly appreciated!
Donations can be made by clicking on the link below
www.paypal.com/cgi-bin/webscr...
PLEASE KEEP IN MIND when you are watching my videos: I am showing you the least expensive, quickest "backyard" methods for repairing or servicing your lawnmower or equipment. Replacing all components such as gaskets and fuel lines is always recommended when rebuilding or repairing equipment. With these videos I hope you are able to fix and repair your lawnmower yourself with minimal parts, knowledge and tools. Thank you for watching!

Опубликовано:

18 июн 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 242

@chiennguyenthanh1745 11 месяцев назад

Lightweight is good and what did I use it for it’s a lawnmower ru-vid.comUgkxTPN04aT-Qdjr_KS3ql7ng8wnU3wwsCqk also recommend Yes it is lightweight so hence not as robust as our old one. But if you take care it does the job really well.

@paulatreides7 3 года назад

I've got a GCV190 on my mower that is very hard to pull. It runs fine, just getting it to turn over is a challenge. I haven't spent much time diagnosing it as I haven't had it long. But I think I know exactly where to look now. Thanks Jeff!

@OceanofMaya 3 года назад

This video should have some more views. He's pretty helpful.

@novisnick6928 4 года назад

Love the education you share! Greatly appreciated

@cedargroveopryalamoga2873 3 года назад

Thank you so much for the video. That’s exactly what the problem was with mine. Running great now!

@rogermcdonald1607 4 года назад

Nice repair sir! I never have seen that on a honda engine. Nice catch! Roger

@mdbmdb001 4 года назад

Great video. Thanks for the detail and specs. 👍

@netdoctor1 2 года назад

_"They always seem to loosen up a little bit... after you tighten them down."_ Makes sense. The locking nut is pulling the screw outward as you tighten it. Thanks for sharing with us, Jeff.

@joesinakandid528 Год назад

THAT is the second reason for the square head - to stop that movement. The same concept for all valve adjustments.

@marcobrownstone 2 года назад

Outstanding! Best explanation for what my generator was doing. Just adjust the valves, easy fix. Thanks for the help.

@JeffsLittleEngineService 2 года назад

glad it helped

@marionake5618 3 года назад

Mine is impossible to pull ; now I know why . Thanks for a great video.

@rustyrepairs2565 4 года назад

Very helpful information. Thanks!

@saltysunburn2913 Год назад

Great video. Thank you for spending your time to make a damn good video for everyone else.

@JeffsLittleEngineService Год назад

Thanks friend!

@FanGaryMoore Год назад

I have a Husqvarna self-propelled AWD that I was ready to scrap. I remembered having a similar issue with valve train on a B&S 21HP on my old John Deere D120. I googled it, to confirm, and found your video. Lo and behold, I have a cracked exhaust rocker arm. I'm going to do the same as you, with the new seal. I found another thread, where the engine guru suggested Loctite 620 on the guide, before driving it back into place. I think I am going to do both. Better safe than sorry. Thank you so much Jeff!

@JeffsLittleEngineService Год назад

Thanks for watching and for the comment

@Habel420atgml Месяц назад

Wow man thank you so much you saved us from having to replace a pressure washer! That was a great video well instructed no BS. Thank you very much I greatly appreciate what you did. I had the exact same problem with the exact same exhaust rocker arm and now I know exactly what to do thank you

@JeffsLittleEngineService Месяц назад

Glad it helped

@georgeclapenstein7823 3 дня назад

I’m pretty sure this is the same issue I’m having… I’ll find out this afternoon

@TheMAC0876 2 года назад

WOWZ I just got one of these from my friend for free. Having the same problem. About to get working on it. Thanks man!

@gregrandolph2845 3 года назад

Yup, just pulled my honda gcv 160 valve cover and I have the same crack. Thanks for the video.

@gregrogers6088 3 года назад

Very helpful video. BTW I thought I found you spark plug LOL!

@sergiobenitez6889 3 года назад

great explanation,perfect video.thanks

@marshallborder9089 3 года назад

Thanks Jeff , your a good teacher .

@JeffsLittleEngineService 3 года назад

thanks friend

@fleadoggreen9062 11 месяцев назад

Lol I liked how you put the other tools in ur hands down while u were trying to adjust the valves with the feeler gauge

@dennisalcapone3568 3 года назад

Thank you sir, great workshop STAY SAFE

@JeffsLittleEngineService 3 года назад

Thanks, you too!

@floydfan4959 3 года назад

Thanks for the great vid !, my karcher pressure washer with a honda 190 has been pulling the cord out of my hand for two years and never knew why .Last week i was stripping the stain off my deck in the hot sun(90 degrees) and it finally died, saw your vid and sure enough the exhaust rocker cracked and bent, I.ordered the Honda rockers from Amazon only to realize the pivot pin that holds the rocker was trashed too. I replaced and gapped them and the engine starts easy again and runs great.$25 fix So before you order, check the pivot pins. Thanks so much!

@johnkomosa4089 Год назад

Thanks, great tip on the pins. You guys are awesome.

@scotthawthorne6122 Год назад

Thanks Jeff, I was about to throw mine away today(husqvarna lawnmower). Every video I saw was concerning the carb. And mine was perfect. Watched your video, and that was exactly my problem. Saved me $500 and it now runs beautifully. Thanks again for the great video.

@JeffsLittleEngineService Год назад

Glad it helped

@Captpisscums 2 месяца назад

Clear gas will solve carb problems

@bbulliard 3 года назад

Great and interesting video. Well done w very nice detail. Thanks a bunch

@JeffsLittleEngineService 3 года назад

thanks for watching

@wiserman100 3 месяца назад

Top Dead Center on COMPRESSION stroke. Good concise video. Thanks.

@Glenn_123 4 года назад

Great video!!

@jualrola1 3 года назад

Very good video...Appreciated.

@bensabiston470 3 года назад

Very interesting, I have a Troy bilt tiller with a similar Honda that MIGHT have this issue?!? Thank you

@adrianslk1 3 года назад

Thank you, for the tips, my rocker arm wasn t broken but the valves were way out of spec, now it fires without issues, thank you for your time

@JeffsLittleEngineService 3 года назад

Glad it helped

@johnkomosa4089 Год назад

Bent rocker arm? Not broke but bent? Will it bend see more? Weak fatigued metal? Thanks for the info

@Gtrellis 2 года назад

I have got a gcv200 mower, man was that hard to pull start. Just done valve's couple times so not happy. I went to the spark plug first to take out, found that the spark plug was not tightened up, simplest fix.Easy to pull now, starts OK. Not experience at this, I tried the stick method for top dead centre found tricky, I tried small led light in spark plug hole a little better for me.But hey thanks for you help, not to be rushed couple days thinking out is better than couple weeks down shop.

@johnbauer9223 Год назад

Thank You for this video also, after I took the cover off I discovered a stuck intake valve. A little soak with WD40 ans a small tap it popped up. Thank You!

@1keykneedeep 4 года назад

Awesome sounding machine

@apetro8895 3 года назад

Looks like a weak point. I had the same problem. Video was very helpful. Thx!!

@DeepishMoog 2 месяца назад

Engines, stick edgers, weed esters, pressure washers, they all work dandy when consistently used. They all seem to get issues when sitting too long (like over the Winter). Regular use, oil changes, ethanol free gas, and you're golden. Except with pressure washers, I've always had more troubles, not with the engine, but with water pump. It's like $150+ service around here to have it reconditioned. For that price, it just might be time to replace the pump DIY.

@turk59 Год назад

That second call was me trying to tell you where your spark plug was 😂

@321CatboxWA 3 года назад

The arm band helps . thanks for posting this fine video. I will never trust honda the same.

@philliphall5198 7 месяцев назад

Watch for exhaust guide moving up and stopping valve movement, which breaks the arm, can put the intake valve seal with rubber removed on exhaust and new intake seal installed once guide is driven back down 😊😊😊 It works and will stay put 😊 Thank You 🙏

@JeffsLittleEngineService 7 месяцев назад

Good tips

@luisegallegos8120 2 года назад

Nice and clean job, tnk'u with the video helps me a lot, saludos desde Michoacán México mil gracias

@JeffsLittleEngineService 2 года назад

Gracias amigo

@annierenard5954 4 года назад

very good video thank you

@redskiclayton Год назад

If you look down at the flywheel there is a dowel sticking out. Line that up with the notch in the case where the valve cover mounts. It does not matter if it is compression or exhaust stroke on this engine.

@jr0079 Год назад

I did exacting what you did but the thing I didn't was replace valve cover gasket. I tightening it well no leaks its hard to beat Honda factory parts.

@johnkomosa4089 Год назад

Thanks for the tip Jeff, I think that's my problem. My buddy's mower has been pulling hard for awhile , now poping through the carb.

@JeffsLittleEngineService Год назад

Heating up the valve cover helps in removal

@philliphall5198 Год назад

I agree on heating up cover and look very closely for a cracked rocker arm

@a.krueger6486 3 года назад

Thanks John.

@deebeeisme 3 года назад

Thanks. saved a visit to repair shop.

@steveback4250 3 года назад

Fixed my problem in 20 minutes. Tks

@JeffsLittleEngineService 3 года назад

nice work!

@lordfordification Год назад

Thank you for the video.

@JeffsLittleEngineService Год назад

Thanks for watching Buck

@mikesbarn1858 4 года назад

Scot h bright pads work great removing gasket and sealant debris

@SheikShak 3 года назад

Nice video......well done.....

@JeffsLittleEngineService 3 года назад

Thanks for watching

@tubeswim 2 года назад

I had this issue. Straight out of the box! Removed sparklplug and was then able to pull the cord. put it back in and good to go.

@JeffsLittleEngineService 2 года назад

wow that is crazy!

@seanoconnor1398 Год назад

The reason I’ve cracked my intake valve before is because the guys weren’t practicing proper pump operation paying attention to the pump itself and making sure they always are doing a pressure release after shut off. They’d go to shut it down and wouldn’t release the pressure after shut down and then would not perform one before Pull starting it. They’d just go to pull start it not giving attention to the extreme compression all of the sudden and instead of taking the wand and pulling the trigger to release the pressure they’d just muscle it like they’re kick starting a Harley. You’re only going to make that mistake so many times until the engine or pump or both give up on ya. So yeah it’s real important to release the pumps pressure after shut down and before start up if you want the pressure washer to last.

@ravineelpify 6 месяцев назад

Thank you sir❤

@nashguy207 3 года назад

Professional goof off does a great job helping to clean off the old rtv silicone

@johnsturges1485 Год назад

Mine was so hard to pull the kickback was enough to pull your arm off. Pulled the valve cover and no crack on the rocker arm, but the exhaust valve did seem like it had too much play in it. So I set the gap to the OE specs, and boy it's like night and day. Pulls with little effort now and starts on the first pull almost every time! Thanks for the help as I was getting frustrated in why this was so hard to pull!

@JeffsLittleEngineService Год назад

Good work. Good job figuring it out.

@wasifhusain3069 Год назад

Thanks for a great video. Just a little suggestion, TDC on COMPRESSION stroke. Combustion stroke or Power stroke is downward. Sorry to point that out. Great video . Thanks

@eostrike 9 месяцев назад

I was about to comment the same. Good job here!

@jcamerica09 4 месяца назад

I have a GCV160 Same problem Did calibration is the same Ex 0.08 Intake0.06 I appreciate your help jeff

@JeffsLittleEngineService 4 месяца назад

I am happy it helped.

@garrettlee4293 5 месяцев назад

good video

@watermanone7567 4 года назад

Nice fix Jeff: I found that if I changed my customers over to synthetic oil that it helps to stop valve seizing on those engines that run hard like on pressure washers. Thanks for the video.

@JeffsLittleEngineService 4 года назад

Good tip!

@zackanani2508 4 года назад

Can you please tell me what kind of synthetic oil should use with Honda GVC190 and the weight??

@conner5611 3 года назад

@@zackanani2508 synthetic 10w30 or 10w40 both are fine I run partially synthetic 10w30 no problems yet

@wrb1000 3 года назад

Not in my case. I use Mobil 1 and last week it refused to restart after a long run. Just get one backfire when I pull the cord. I haven't opened it yet (I was here to learn), but I fully expect a stuck valve and/or cracked rocker. This video gives me the confidence to move ahead. Thanks!

@watermanone7567 3 года назад

@@zackanani2508 Any brand name 10-30 for summer and 5-30 in cold weather, Also a synthetic blend is good.

@FixItStupid 3 года назад

Just Thank You, Sir We All Part Of Fix IT Thank You The Net Work Works My Unit Fixed Thank YOU ! Best Recycle Fix IT

@SaldosInc Год назад

Thanks for sharing

@JeffsLittleEngineService Год назад

Thanks for watching!

@romyenglish 3 года назад

Thank you

@PaulHigginbothamSr 2 года назад

Jeff should have let the cover sit for an hr before cranking the piss out of it with his worn out 10mm. That way the body builds up in the sealant. I found that out with my transmission on my Dodge Journey. After I ran it down finger tight I let it sit all night and it sealed up finally tightening it the next morning.

@JeffsLittleEngineService 2 года назад

lol! good tip!

@Anubalfer 2 года назад

The cam lobe on the one I'm fixing now doesn't match dead center when the piston is at max height. Is this a problem? I know the markings on the underside of the cam match the lobe at center with the cam housing. Mine is off to the left at max height.

@clauslundberg9224 4 года назад

Super repair Jeff. Any ideas as to why the exhaust valve got stuck?

@JeffsLittleEngineService 4 года назад

not sure. possibly a low oil situation.

@clauslundberg9224 4 года назад

@@JeffsLittleEngineService Thanks - and keep up te good work. Really enjoying you videos

@philliphall5198 7 месяцев назад

Seems it’s very very common if the oil level is low and sticking valve exhaust in guide 😊

@Donzi33z 3 года назад

Had the same engine Tuliped an exhaust valve Was hard to start from day one Is there any way to adjust timing on this engine? Timing belt timing was correct

@seanbrown7954 3 года назад

Heck ya I thought my pump seized up but turns out same thing is wrong with my engine. I noticed it starting puffing black smoke and shut off.

@mikefuqua5321 2 года назад

I have a GC190 on my pressure washer vertical version. Upon looking at the valves the intake rocker was really loose. If you adjusted to the .006 the adjusting screw was almost all the way in, not enough threads to install lock nut. Looking for what would cause this? I now have taken the engine apart and ordered new valves and springs. Have not pulled the flywheel off as yet so I have not been able to look at the valve itself.

@JeffsLittleEngineService 2 года назад

make sure the valve guides and rocker arm stud have not come loose

@mikefuqua5321 2 года назад

After tearing it apart it was the valve seat had wobbled enough to come loose from the aluminum block I'm going to try to stake it to keep it in there for future years

@philliphall5198 Год назад

If rocker crack be sure and check compression release spring and plastic gear for damage

@hellohello8556 3 года назад

Hello from Australia🇦🇺. Great video thankyou. Did you wait to let the liquid gasket paste set before starting the mower? Also i have 2x 196cc electric start mowers that are hard to pull start even when they were brand new they were hard to pull. Would it most probably be that the valves were not set very well from factory or could there be other reasons why they feel so hard to pull start?

@JeffsLittleEngineService 3 года назад

yes I try to let it dry overnight. Hard starting could be the valves or something else. It is not likely though that they were set wrong at the factory but maybe possible. Thanks for watching

@hellohello8556 3 года назад

@@JeffsLittleEngineService thankyou fir taking the time to answer my questions. 👍

@haroldvelasquez9185 4 года назад

I have the same issue the engine is locked I opened that cover everything is good I don’t know what else to check thank you

@paulbillings1791 3 года назад

Carburetor could have flooded and filled the cylinder full of fuel. If this is the case,the rings won't hold all of the fuel in the cylinder,your oil level is going to be high and your dipstick will smell of fuel. The carburetor float valve and or float valve spring are your typical culprits.

@toroon 4 года назад

great video. Barely heard the chickens.

@FixItStupid 3 года назад

LOL Got That Species Too Lot Of Work & Worth Teaching Thank " You" , & Jeff

@jgro1976 3 года назад

So, those engines do have markings on the cam gear, two little lines that level out horizontally with the edge of the cylinder block (would have been facing down with the orientation of the camera/engine), and the crankshaft has a line/arrow that lines up inside (had to replace the crank on one of these), once those are all lined up respectively you can re-install the timing belt and re-assemble. I am now curious though to check my valves, as I am also having a hard time pulling mine/getting it to turn over. So thank you for this.

@Anubalfer 2 года назад

Can you confirm that the cam lobe is dead center with the piston at max height? I'm doing mine now but the lobe is off to the left at max height. Does this matter?

@jgro1976 2 года назад

I would say that yes it matters, even one tooth off could make the difference between running properly with correct timing and not. Just like how a vehicle would not run properly if it was off a tooth on its timing.

@avrracer4175 Год назад

Hey Nice Input. What can it be on a GCV530 a cold start is on point but if the Engine was hard on work and I Stopp it and will do a warm start the Engine turns but no Start in 90% of cases. Compression is 4,2 Zyl 1 and 4,8 for Zyl 2 (6-8Bar) Sparkplugs Ignition Coils are new, carb is clean. Cause my fault is exactly the opposite of yours. With Choke the warmstart works...

@JeffsLittleEngineService Год назад

warm start problems often indicate that the carburetor is flooding and needs to be rebuilt

@avrracer4175 Год назад

@@JeffsLittleEngineService thanks for answer. On weekend i checked the valve and they are in good condition. The cam wheel and decompression works fine. So the last two things are the carb and in worstcase the piston rings

@northpoint1039 4 года назад

Thank you for the good video. Now the question comes up - Why did it crack? Perhaps the gap was incorrect at some point and put too much stress on it?

@robbieaussievic 4 года назад

..... Engine operated vertically and/or low on oil ? valve stem dries & ceases, rocker tries to compress valve & cracks ?

@JeffsLittleEngineService 4 года назад

The valve was stuck when I opened it up

@Jim-ie6uf 4 года назад

Rob Robbie only the cat knows an he ain’t telling. Sometimes stuff happens, Honda parts are plenty available and inexpensive.

@candycoatedrazrbladz 4 года назад

On my gcv 190 the valve guide/seal slide up out of place which caused the valve to lock up. In turn cracked the rocker arm. The valve was not actually stuck or siezed.It could not go down since the guide came up and out of place.

@graggcain9496 4 года назад

Jeff how do you find specs for value adjusting, compassion on different brands or what?

@JeffsLittleEngineService 4 года назад

if I don't have a manual I look it up on google

@Jim-ie6uf 4 года назад

Gragg Cain google

@Jim-ie6uf 4 года назад

Gragg Cain if you need an IPL, go to ereplacementparts.com. , there you can see a diagram and find part numbers, and order parts if you want. Great company to do business with, though I think shipping is kinda high. Or shop on the webernet

@menditman2004 4 года назад

Hi you mention in the video you tapped on the valve with a hammer to loosen the stuck value, I’ve had problems on 2 of these engines a had the rockers crack due to valve guide slipping, I think that is what happened to yours. I tapped mine back into place it lasted a little while then slipped again. I’d be surprised if this machine lasted very long before the problem came back as it will slip again. I just swapped the engine in the end. I’ve only had it happen on the 190, the 135 and 160 I’ve never seen it happen on those. Good video.

@andyhamilton8940 4 года назад

Pressure washers have a back and forth torque load while in use causing a shock load known as water hammer. This transfers to the crankshaft and ultimately the valve train causing valve springs to be tested to their maximums. The timing belt is rubber and stretches to absorb the shocks. Remember what happened when your feet slipped of the pedals on your bike when you were a kid? Same principle.

@netdoctor1 2 года назад

Could be that the exhaust valve guide is migrating out of the case, and contacting the rocker arm. I made a video in which I address this issue. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-zZz0MRqxGX8.html

@petequinones3454 3 года назад

I've seen the cracked exhaust rocker on enough of these Honda 160&190's to conclude it's a bad design that too many are suffering from. Honda really should have addressed this by now, or they make a lot of money from selling so many rockers?

@jazpanoz4996 3 года назад

Parts revenue $ every brand has some component that is designed to fail:/ These rock arms fault is they lack metal thickness in the area they crack:/

@johnkomosa4089 Год назад

Yep, product recall, folks getting hurt from pulling kick back. Put some heat on Honda they can afford to fix their f up. At least offer the part for free. Reputation...

@philliphall5198 Год назад

Yep cracked rocker or spring damage plastic gear on compression release Every time

@philliphall5198 7 месяцев назад

I agree the exhaust valve is not getting enough oil and it’s trying to stick to guide You can count on where the problem is every time and on hundreds of them 😢😢😢

@mikesbarn1858 4 года назад

I saw the spark plug over there. Tried to tell you.

@JeffsLittleEngineService 4 года назад

I searched for about 10 minutes..

@FixItStupid 3 года назад

@@JeffsLittleEngineService New Sub In The Net Work U R TY

@animalcorvair 3 года назад

glad i have briggs on most of my stuff

@simonhernandez3354 Год назад

So I picked up a craftsman 3000 psi 190cc the pull cord wouldn’t move at all took it and spun by hand nothing it spins halfway smh then stops and sounds like it hits a metal. Took the top nut off sprayed it with penetrating oil and spins good till I tighten the but on and does the same thing. Any idea wat it could be

@JeffsLittleEngineService Год назад

broken rod or a stuck valve

@romyenglish 3 года назад

Hi Jeff. I bought brand new rockers, I replaced them both, adjust the valves, first rope was fine. After that same story, it's ripping of my hand. Any ideas? Thanks

@JeffsLittleEngineService 3 года назад

I would recheck valves or possibly a sheared flywheel key

@joesinakandid528 Год назад

@@JeffsLittleEngineService OR the exhaust valve guide partially pulled out.

@theeverykindgunguy622 3 года назад

i noticed when you took of the cover every thing was clean , when i took my off it was all in oil , is it supposed to be like that

@JeffsLittleEngineService 3 года назад

some oil gets up in there. If it got tipped or too much oil can cause alot up in there.

@theeverykindgunguy622 3 года назад

@@JeffsLittleEngineService is it a bad thing if it get tipped over

@BUDD1954 11 месяцев назад

I have a very similar power washer but could not find the model and serial number to purchase the water inlet tube.Could you please tell me what is the model and serial number of your GCV190? Thanks for your help

@JeffsLittleEngineService 11 месяцев назад

This was a customers power washer so I do not have it

@joyler2446 3 года назад

You need to seal the valve cover with Honda bond

@smoc5260 2 года назад

What spark plugs do they take I need one for mine

@JeffsLittleEngineService 2 года назад

NGK# BPR5ES

@pennyglisson4450 Год назад

Mines been wonderful except I’ve not been able to figure out why my soap ain’t coming out ‘? I’m sure it’s on my end. maybe anyone know. I’m watching your video now just started 🤞!!

@3613jeremy 11 месяцев назад

This Ryobi pressure washer has oil burning white smoke coming from the pull start after it starts up I stuck a camera down the cylinder and it looks like the cylinder bore has deep gouges from the rings I would thing but I'm definitely getting annoyed by it

@philliphall5198 Год назад

Owners need to keep extra exhaust rocker and timing gear They will need them

@hardikkadia7125 2 года назад

What can i say ? It was same problem and once i have adjusted to 0.006 and 0.008 shims and works like butter. Thank you so much. Mr. Jeff.

@JeffsLittleEngineService 2 года назад

good job! Thanks for watching

@elysepellegrino7412 3 года назад

Why did it get stuck in the first place? I loosened my valve by tapping on it but it still sticks a little but I can push it down. How can I determine the reason for this?

@JeffsLittleEngineService 3 года назад

good question. lack of oil or a manufacturers defect

@garytman007 Год назад

I have a 3300 ryobi pressure washer with a GCV190 and so far it's been my worst investment ever. It won't even start now. It did after I cleaned up the carb etc. It was fine yesterday as for starting it up. Only pressure for half a second and then nothing. Left it outside and it rained today, started for about 10 seconds and died. After it started pulled the trigger and 3 small rocks shot out of the gun lol. It's barely 2 years old. Then it got extremely hard to pull, shut off the water and tried and pulled easily. Turned water back on still pulls, just doesn't start. I guess next step is to check the spark plug. I know what you mean about those valve clearances. I did a complete valve adjustment on my 2000 Honda prelude and it sounded better than before. Took me 2 days to do that. I am at a loss with this pressure washer so far.

@JeffsLittleEngineService Год назад

I have seen the pumps fail and make the engine hard to pull the rope/hard to start. The rocks may have gotten into the pump too.Try using starting fluid to see what happens

@ivanhmunguia5576 3 года назад

So how do you get it unstuck without braking anything? Just lube it first??

@JeffsLittleEngineService 3 года назад

yes and work it free gently if possible

@ninjasfanfunnystuff9026 2 года назад

My exhaust valve was stuck too. I pushed the valve into the cylinder and ball honed the guide. After assembly, it about broke my hand trying to start. After watching this I see the broken rocker arm! What causes the valve to seize in the guide?

@JeffsLittleEngineService 2 года назад

since I have seen a few like this it must have been in error made at the Honda factory

@MegaKencam Год назад

That is exactly what happened to mine

@scottstalnaker4179 2 года назад

Well, the locknut is missing on my exhaust valve. Now what? I guess it's in the crankcase somewhere but how do I access that?

@scottstalnaker4179 2 года назад

Maybe I'm living better than I thought I was. I tilted the machine to the front in a big was tub and shook it the best I could. lol and behold the nut fell out. Now we'll see if there's any damage.

@johnkomosa4089 Год назад

Good job, how did it turn out, Scott?

@scottstalnaker4179 Год назад

It actually turned out good, sorta. I reinstalled the locknut, adjusted the valve to spec and it started right up. I ran it a couple times for a total of 30 minutes or so. Later it wouldn't start and appears the exhaust valve is stuck open, not fully closing. I haven't gone back into it yet.

@herounlocks6891 2 года назад

what is that measuring ruler called on 8:24 ?

@JeffsLittleEngineService 2 года назад

A feeler gauge

@jerylr5949 2 года назад

My 190 gcv engine in my pressure washer would not start after shutting it down to move some items in my deck. Checked the fuel system, found no problems so I removed the plug and checked for spark. Had spark. Checked for compression, none. Removed valve cover and noticed about 1/8" gap between rocker arm and valve on the compression side. Noticed the exhaust valve was stuck in and I took a screwdriver and popped it out. There were no cracks in the rocker arm. Don't know if the piston has clearance for the valves or what could have gone wrong or if this thing is worth fixing. Paid extra for the honda engine on the husky washer. Engine only has 40 hrs on it. My mistake.

@JeffsLittleEngineService 2 года назад

I have seen that before. you can ping around the guide to help keep it in place if needed

@johnkomosa4089 Год назад

Peen, humm , thanks for the tip Jeff, again..

@bigdogbrosadventures8371 10 месяцев назад

All good till the next time the valve guide works its way out again.

@prant8998 2 года назад

#1, Make sure there’s no pressure in the hose or at the pump. Without pressure she pulls right over.

@philliphall5198 Год назад

I remove every water pump that comes in shop first thing I’m not buying them a new washer pump period

@christopherthumm4046 3 года назад

Could you weld it and her her donebob?

@JeffsLittleEngineService 3 года назад

maybe

@Jpilgrim30 Месяц назад

No need for all of that top dead center stuff. You can see the cam lobe right there. All you have to do is set the lash when the exhaust rocker is on the base circle of the cam basically when the lobe is opposite the rocker

@JeffsLittleEngineService Месяц назад

good tip