Finally Finishing The Blazer Tank Install In My S10! (LEARN FROM MY MISTAKES!!!)

Подписаться 6 тыс.

Просмотров 14 тыс.

50% 1

I finally finished the filler neck and re-did a little fab work on the Blazer tank in my 1993 S10. Also mated a Walbro 255 fuel pump to a stock 1993 Blazer fuel sender. The parts I used are linked below!
Earl's adapter fitting
www.summitraci...
Earl's adapter fitting
www.summitraci...
Tanks Inc Filler Neck/Cap
www.summitraci...
Fuel Tank Strap Isolator
www.summitraci...
Walbro Fuel Pump
www.summitraci...
Spectra Fuel Sender
www.oreillyaut...
Precision Fuel Tank
www.oreillyaut...

Опубликовано:

17 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 39

@PeterHatch-mx7zc Год назад

How many gallons is the tank please

@patseidl990 3 года назад

I’m putting in a Ridetech air ride system in a 93 s10 short box step side, looking to relocate the blazer tank to the rear, didn’t know if any one has used this system and moved the tank also? Thank you for looking..👍

@derekczeschin5623 2 года назад

What did you do for a vent for the filler neck?

@Simpson3386 2 года назад

which Walbro pump is it.. i type Walbro 255 at summit racing and i cant see which one is the right one

@internallycombusted1 3 года назад

What did u do with the 5/8 vent. I'm doing this currently and really want to keep the vent

@ericwilkes238 3 года назад

Do you have. To worry about rain water getting in to the push button spout.

@wesco123 3 года назад

Excellent work 👍

@carmelogalarza7764 4 года назад

The s10 is looking great

@ronnelson7828 4 года назад

I've been contemplating the Blazer tank swap in my Dime for a few years and your videos have finally made it clear on how to make it fit. I would prefer to have the outside filler door setup moved back to the rear. Not sure how easy that will be to put together, but we'll give it a go. Thanks for the inspiration!

@UcantBeSerious03 4 года назад

good stuff, watched several times - doing one of these tanks into a 55 pickup

@buddy18414 4 года назад

Enjoying your vids. I'm starting a similar build. LM7/T5 swap into a 94 S10. Got the motor and trans, still gathering parts befor I start tearing down. Thanks for sharing!

@CheekyGarage 4 года назад

Thanks! Sounds like a fun build. Best of luck with it!

@renwickconolly2839 4 года назад

GREAT VIDEO !! THANKS for sharing!

@internallycombusted1 3 года назад

Is that the 13 or 20 gallon tank?

@oldcarguy9827 3 года назад

Thank you for this I am wanting to do the same thing on my 92 S15. Looking into ways to rout the filler neck differently on mine but very helpful video. Again thank you.

@buddy18414 4 года назад

I wonder if you could have have welded the 1st one w/ silicon bronze rod?

@CheekyGarage 4 года назад

I thought about it later, but I had already knocked it back off, and warped up the hole by doing so

@jeffbrevelle2095 4 года назад

Why did you go to the blazer tank ? Benefits ? Thanks for the content One more question ! How do you keep the shop so clean ? Lol

@CheekyGarage 4 года назад

I wanted to swap in the Blazer tank to move weight rearward, centered between the frame rails. And I try to keep a clean work area in the garage, but I can assure you, 90% of the time, a tornado has just come through behind the camera lol

@jeffbrevelle2095 4 года назад

Cheeky Garage thanks. I guess I was weighting the benefits verses rewards. I remember the pinto gas tank fiasco. I have been run in to 3 times in my 1500 Silverado and jag so I’m a bit concerned about placing gas tank there. I loved your fit mint and welding. Did you back purge. I’m willing to bet you did because of the quality on the weld. What type of blade did you use to cut the stainless. Nice cuts on that smal pie cuts.

@TravisPlumer 4 года назад

Where did you get that tank and sending unit? I'm gonna need a new one.

@CheekyGarage 4 года назад

Both came from O'reilly's. Just normal replacement parts stuff

@TravisPlumer 4 года назад

@@CheekyGarage thanks man, love your build!

@CheekyGarage 4 года назад

@@TravisPlumer Thanks man! Glad you dig it

@stoneyswolf 3 года назад

What's the point in doing this? What's wrong with the original tank location?

@THSGUY 4 года назад

My thought with that style gas cap IS that dirt & rain will get into the tank.

@CheekyGarage 4 года назад

I plan graft a shrouded gas door into the bed floor, so it won't be much different than newer vehicles that come stock without a gas cap

@haileyzworld1 4 года назад

Thats pretty cheeky Cheeky! I like it!! Dig the gas cap, how or where could I get one ??

@CheekyGarage 4 года назад

Thanks! I put links to everything I used in the description

@ryancasteel4929 4 года назад

Great work tommy. The filler neck looks good. Im enjoying watching your progress on this swap. Im curious though what your plans are for the hole in the bed to acess the filler neck? I would be worried about trash getting through that push through style cap withoutnsome sort of door covering it. Especially if you're carrying something in the bed. Keep up the great work!

@CheekyGarage 4 года назад

Thanks buddy. The plan is to graft a gas door in the bed floor to keep it covered up and still looking stock-ish

@chrisbishop6399 3 года назад

Hey Tommy did you ever get the filler neck door finished on gumby? If so would like to see what you come up with

@zoefaith120 4 года назад

I always thought of a second gas tank in the S10 but. It's not really needed.. it would be to have extra tank for gas mileage. I hope in the floor be lots better than on the side.