How to Change a Snow Blower Friction Disc | Ariens®

Подписаться 21 тыс.

Просмотров 166 тыс.

50% 1

Does your snow blower struggle to drive forward? If that's the case, you may need to replace your worn friction disc. Watch as we replace the snow blower friction disc in an Ariens Deluxe 28 model Sno-Thro. As you can see, it's easy doesn't take much time and can be completed in the comfort of your own garage.
Buy a snow blower friction disc at our online parts store: parts.ariens.com/searchresult...
Don't have an Ariens Deluxe model? That's ok, because the friction disc replacement procedure is similar across all Ariens snow blower model platforms. As always, read the safety section in the operator's manual before attempting any service procedures and follow along with the instructions in the service guide for your unit.

Хобби

Опубликовано:

17 фев 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 119

@dtom1145 2 года назад

On a machine that has never seen a snowflake. No wonder it is soooooo simple!

@skiprope536 3 года назад

Sure. Try doing this with a rusted hex shaft that ate the bearing up on the right side. In 28 degree weather.

@irvingj.smacklebits7585 Год назад

Thank you for a well done video without taking a lot of time to get across the needed information.

@markfinnestad3618 3 года назад

I've only owned Ariens for two years, but am impressed with the quality. I wish that I had discovered your products 20 years ago!

@cardo1111 3 года назад

Better late than never 👍🏽

@Bwn-rl3gl 3 года назад

I replaced my friction disc on my Ariens snowblower by using this video. I was taking the snowblower to a repair shop to be repaired. The total time from removal to replacement was thirty minutes. When I tipped the snowblower over gas was coming out of the carburetor. I placed it back on its wheels. I started the snowblower and turned the gas flow off. The engine stopped and I flipped it up. No fuel came out of the carburetor. This video saved me time and money. When I picked up the friction disc I asked the person if they sell Ariens anymore. There were none on the showroom floor. He said that they were sold out and on backorder. Thank you for this video. I also used Partstree to look up where one washer went.

@AriensChannel 3 года назад

Thanks for the feedback! We're glad this content was useful for you!

@micharris1761 4 года назад

I have done this a long time ago, but these video's are so important and cool ty

@cayman9873 2 года назад

I bought a 1966 ariens sno thro 40 years ago. It still works great. Amazing machines..

@christophers7059 2 года назад

I bought a top of the line Ariens that is only a couple years old and the drive wheels failed the first time out. Friction disc probably. I'm not impressed.

@therealsparkman Год назад

Thanks for sharing the video. It really did help! Although, in reality, your machine is brand new with zero grease and crap and mine was gummed up with shredded rubber from the wear on the friction wheel. The wheels weren't easy to take off either due to dirt and whatnot. It took a bit longer than this five minute video, but she's done! Woot! Cheers!

@robertwalter1370 Год назад

Thanx man! Now my old Husqvarna snowblower from -95 is like new. Power and speed is back! Best regards from nothern part of Sweden by the polar circle 😅

@cardo1111 5 лет назад

Well done. As an Ariens owner I really appreciate these great how to vids.

@AriensChannel 5 лет назад

Thanks! We're learning what an important asset these are to our customers. We'll keep 'em coming!

@allenkosidowski9076 3 года назад

Well done video indeed ,with the quick how to I was done in 30 minutes!

@AriensChannel 3 года назад

Good to hear, Allen! Glad we were able to help.

@garyduran1 3 года назад

Thank you Ariens. The hardest part was getting both wheels off. They were stuck good.

@AriensChannel 3 года назад

Remember to lubricate your axles each season!

@garyduran1 3 года назад

@@AriensChannel will do. Thank you

@cayman9873 2 года назад

I have worked on snowblowers for decades. Your video is excellent for folks that have not done work. The machines are not hard to service. So you did a great job

@georgepoirier9014 2 года назад

Great to work on BRAND NEW snowblower !!!!!!!

@Hammerthumb1 5 лет назад

Start out by cleaning the drive plate and friction disk with some degreaser to get rid of all the gunk and oil. This will help greatly with slippage and may save you having to tear it apart. As far as replacing the disk, the hardest part may be removal of the wheel since the shaft has probably corroded over the years. You could try a wheel puller or knock it loose using hammer and pry bar. Might want to bring the old part to the dealer to make sure they get you the correct replacement. On 920 models, rim part gets replaced and is held onto carrier bearing with three star drive screws. They are tightly torqued and I had to clamp the rim in a vice to get them loose.

@AriensChannel 5 лет назад

Helpful comments! All the more reason for everyone out there to grease their snow blower axles annually, or more if necessary. Cleaning and lubrication as instructed in your operator's manual are some of the best things you can do for your Ariens Sno-Thro.

@88omarz 4 года назад

Any suggestions on removing a seized bearing. Mine on the right won’t come off

@alandinsmoorcontractingser7119 Год назад

He did mention to drain the fuel...but u also need to drain the oil 🛢

@jasonwrner 9 месяцев назад

@@88omarz Same here. I just came back inside to see if I completely missed him removing the bearing flange on the right side also. Guess not. Apparently the round end of my hex shaft on the right is just going to take a little persuading to slide out of the bearing. I don't remember exactly but seems like I should be able to use an extension with an oversized socket, one size drive higher than the extension of course, butt the socket up to the outside of the machine, slide the extension through the center of the socket, make sure to line it up with the end of the shaft and gently tap it with a mallet. Slowly moving away from the word gently until it lets loose). That's my plan anyways. Probably lose patience after a few minutes and start swinging the 30 oz Estwing Happy Gilmore style.

@Peter-976 3 года назад

Nice video on that guys arm. Do you think you could have put the camera in a top-down position so we could actually see what is being done?

@AriensChannel 3 года назад

Sorry about that, Peter. This was one of our earliest videos. We're getting much better with our production quality 👍

@danbaxa Год назад

I put about 10 hard hours on our new Deluxe 24 when it stopped working. After removing the bottom cover I found the friction disc was completely destroyed with chunks torn off and shredded rubber covering the bottom cover. Is there something out of adjustment? The blower worked good for a while, but why am I having to replace the disc already? I have the disc ordered.

@IMEMINE. Год назад

Good step by step. Question… The friction disc is secured in what manner and how do I know if I need to replace the carrier bearing? Which orientation was the cupped side of the disc removed/replaced. A nice presentation on how to replace a part…as a professional parts replacer, airline aircraft mechanic; I missed the explanation about the main focus of this presentation was addressed Please advise.

@roberth7922 Год назад

I changed out the friction disc on a 921024 model. The drive plate assembly in tight against the new friction disc.Wheels will not turn and unable to move speed selector. Any advice is appreciated

@macii58 2 года назад

When does the friction wheel need to be replaced, is there a particular thickness it cannot go below. What is the thickness of a brand new one? Thanks!

@gregl7743 3 года назад

Video is very easy to understand, replaced disk on an 8 year old machine in 30 minutes. Grease the axle, clean the friction plate and you are good to go. I think shifting on the fly probably aided the early demise of the friction plate.

@AriensChannel 3 года назад

Thanks for the comment, Greg! And you're right... you should stop the wheel drive before shifting, otherwise you'll get premature wear 😅

@jonathanformhals9700 2 года назад

What do you do if the left wheel is frozen to the axle?

@ALGO49able 5 лет назад

Thanks for your video , i di have a Deluxe 30 , My question is how do you adjust the machine to go FASTER in REVERSE , cause it' s so SLOW ??

@AriensChannel 5 лет назад

Thanks for the question. Unfortunately, there is no adjustment to increase the wheel speed of your unit.

@garrycowan4747 4 года назад

al go , Yep i agree, i think the same, but It is a so good machine.

@user-mo5gg9eh7h 3 года назад

At the bottom of the shift rod there is a quick pin holding it to the shift arm. Pull pin and rotate on threads a few turns forgot which way, but reinstall and test.

@jerryguerin9640 3 года назад

Seems so simple , first the right wheel wouldn't come off it took an hour persuation ( I grease every season and end) then bearing frozen on tried everything , penetrating oil , tapping , prying , banging , pry bar their like welded onto shaft ! Got left side off eventually but shaft won't come out of right bearing !!? Mine is 5 years old 28" deluxe series . Your video made it look so simple to change friction disc , I thought I'd try . I'm still trying to get off right bearing to slide shaft out with no luck.

@AriensChannel 3 года назад

Hi Jerry, we're sorry you're having those difficulties. Remember, if all else fails, please contact your nearest Ariens dealer. Our dealers are an extension of our team and are well-equipped to make repairs. www.ariens.com/en-us/dealer-locator

@richpainter3090 5 месяцев назад

great but... I have a track version. How do we get the tracks off. can't find anything on this and the manual is silent and no service manual for the 921023.

@DIYELEKTRONICKITS 3 года назад

He's doing that replacement on a brand spanking new showroom condition machine. And Jimmy D is right Ariens does not grease anything,,, it is a ball buster to change that wheel on a 3-year-old machine,, wheels are frozen on the shaft,, bearings are frozen on the shaft ...It can be done but it is not easy.

@ginogervais6051 5 лет назад

Lets say that I need to do some maintenance gear lube and inspection by tilting the snowblober prior to remove the belly cover, my questions are: Is there a way to remove all the gas to empty tank or does the close position of the gas tank sufficient? Second Is it important that the oil in the crankcase be also empty fefore tilting the snowblower?

@AriensChannel 5 лет назад

Thanks for asking, Gino! Your oil won't need to be drained, however we do recommend draining the gas from the fuel tank. You could try siphoning the fuel, however, as long as the fuel is about halfway down, you can tip the unit onto the front of the housing without risking the fuel dripping through the fuel tank cap. Also, once the fuel is drained, you'll want to drain the fuel from the carburetor bowl: 1. Close fuel valve. 2. Position a small container under carburetor (carburetor is located directly below the engine primer pump). 3. Remove bolt / screw from bottom of carburetor and allow fuel to drain. 4. Reinstall bolt / screw into carburetor. Once that fuel is drained from the bowl, you shouldn't experience any fuel dripping during the service procedure.

@IMEMINE. Год назад

Something about the disk fasteners I missed for some reason…great tutorial except For the fact that the main focus was not addressed during this assembly and installation thereof

@user-pn7vt2mc7n 2 года назад

Hi, tell me the dimensions of the pulley that drives the impeller.

@robertromo4816 5 лет назад

I like the video, the only question I have is how do you know the disk needed to be replaced?

@AriensChannel 5 лет назад

Thanks for asking, Robert. If you notice your snow blower struggling to drive forward through the snow, or if it doesn't drive at all, that could be an indication the friction disc has worn down too far and needs replacement.

@8546Ken 5 лет назад

@@AriensChannel How often does the friction disk need replacement?

@AriensChannel 5 лет назад

@@8546Ken there's no specified time, it's only if you notice your snow blower struggling to drive forward through the snow, or if it doesn't drive at all. That could be an indication the friction disc has worn down too far and needs replacement.

@smithn.wesson495 5 лет назад

@@8546Ken If you start to see multiple cracks in the friction disc or there is excessive rubber shavings in the bottom of your pan, you probably need to replace it. I got 7 years of use of mine before the friction disc needed replacing. On another website, I read typically the friction disc lasts 6 to 8 years, depending upon how much use your snowblower gets each year.

@Lylatoons 4 года назад

On mine the wheels wouldn’t move and upon opening it up found that half the rubber around the friction disc completely torn off.

@skrez5534 5 лет назад

Is there an adjustment for the friction disk or only the engagement of said friction disk? Ex, if the wheels turn and engage quickly with the lever but struggle under heavy snow is there an adjustment for more friction or does it need replacement? Thanks! 2008 era 520e.

@AriensChannel 5 лет назад

There sure is, Stephen. The traction drive clutch cable adjustment procedure in your operator's manual is what you're looking for. The tighter the cable, the more quickly the traction drive pulley engages the friction disc when you engage the lever. The looser the cable, the less apt the traction drive pulley is to engage the friction disc. If you give us your model number and serial number for your unit, we can point you directly to the procedure in your operator's manual.

@skrez5534 5 лет назад

I read through the manual and adjusted it yesterday. I just wasn’t sure if that was only the adjustment for the quickness of engagement or for the level of friction as well. Thank you for the quick response. One more reason to be an Ariens brand loyalist.

@AriensChannel 5 лет назад

@@skrez5534 yup, that's the only adjustment, Stephen. And you're very welcome! Thanks for being a loyal Ariens customer!

@I-LOVE-EARTH 3 года назад

My Compact 24 under no load drives fine, like tipping it back to get back into the garage. But under any load it lurches like a bucking bronco...could this be a friction disk problem?

@AriensChannel 3 года назад

Thanks for asking, Mitchel. It's a bit tough to guess what the issue could be, which is why we suggest contacting your nearest Ariens dealer and explaining the issue to them. Our Ariens dealers are an extension of our team and would gladly help diagnose and resolve the issue, if one exists. To find an Ariens servicing dealer near you, try using our dealer locator tool linked here: www.ariens.com/en-us/dealer-locator

@agualotus 4 года назад

Ariens, I’ve had my 28 delux for about 6 years now, just replaced the friction disk. Your video was helpful, however, a bit more detail would have been appreciated. There are two washers on the friction disk (a standard and a goofy shaped square one with one end angled down) it took a few min. to puzzle them in. They fell off without me noting their position. Otherwise, fantastic how to video. My only complaint about my machine is that I wish it had tracks. Well, maybe when this one dies in 10-20 years.

@AriensChannel 4 года назад

Thank you very much for your feedback, Don! The reason you don't see those two washers is because this unit uses our current friction disc design, which switched from the style you have in your machine about 3 - 4 years ago. The new design is lighter, a bit easier to change, has less vibration, and since it has no metal components, has less chance of rusting to the hex shaft. Just the same, we're glad this helped guide you through your procedure!

@jerryguerin9640 3 года назад

Why do you take off both wheels when only left side is needed to remove friction disc.?

@AriensChannel 3 года назад

Thanks for asking, Jerry. The main reason we take both wheels off is to make the hardware more accessible with hand tools. Now, with a ratcheting wrench, the clearance may not be an issue when removing the hardware. However, you'll thank yourself for removing both wheels when starting to reinstall the bottom cover hardware with your hands / fingers.

@johnmcquaid4986 2 года назад

How do I know when the friction disc is wore out

@jamesvrooman 3 года назад

My snowblower is 25 years old, it's an amazing machine. I moved to an area where the snow is rare (thank god) I used it the other day, just to use it on a couple inches. When I tried to engage it into the slowest gear it hesitated, it would go into second no problem, then back into first with no problem. Any idea what would cause this intermittent engagement?

@AriensChannel 3 года назад

That's a good question, James. First, check the cable that extends from the wheel-drive clutch paddle (on left handlebar) to the bottom of the machine. Ensure that this cable is taut when engaged. If not, you'll need to adjust it. This could also be an indication of friction disc wear, but we can't be for certain. Our best suggestion is to take your machine to your nearest Ariens dealer for diagnosis. You can find an Ariens dealer in your area with our dealer locator tool: www.ariens.com/en-us/dealer-locator

@cayman9873 2 года назад

The horizontal shaft inside the lower cover likely needs a very very light coat of grease. You dont want a ton. And the shiny disc could have oil on it. You clean it with rubbing alcohol on a shop towel or paper towel in a pinch. The small 4 to 5 inch rubber circle disc can also be gently cleaned with a slightly damp cloth with isopropyl alcohol / rubbing alcohol. Makes no difference 70 % or 91 or 99 percent.

@ubon39 3 года назад

It would be great if Ariens greased the axle before shipping.

@carsandguitars7064 4 года назад

Awesome video.Any advice on how to get the wheels off the axle where they are seized on?

@AriensChannel 4 года назад

Hello, we suggest trying to apply penetrating oil and allowing it to sit for a few hours. You may need to apply a few times, however, if this does not help, please contact your local Ariens dealer.

@carsandguitars7064 4 года назад

Ariens I did. Then I added a whole lot of heat. The only way that I see to do it,is to cut the shaft and vane the remaining part that’s stuck in the wheel pressed out with a press. Or carefully cut the rim off the axle with a torch. I would have to see which was more to replace. The axle shaft or the rim.

@mk0246 3 года назад

@@carsandguitars7064 I also cannot get my wheel off either. I believe its seized on there as well. Did you have any luck getting it off? I have the old man bringing a wheel hub puller tomorrow.

@carsandguitars7064 3 года назад

Nighthawk no I didn’t. It was the right wheel so I was still able to get the drive disk off because only the left wheel needs to come off for that procedure.I worked at a small engine shop for about 8 years and there were some that we cut the axle off and had to press the remaining axle out of the wheels. It would be nice if Ariens and the rest of the manufacturers would anti seize the shafts when putting them together. I have a few that I service every year and that’s one of the things I do to every machine. Good luck.

@mk0246 3 года назад

@@carsandguitars7064 SOB - the right side wheel on mine comes off easy. Its this left one that is being a PITA. Well.. I foresee a lot of banging, heating and swearing in my future then. I also agree that would be SWEET if Ariens could apply the anti seize so its customers don't have to deal with this crap. Paid 1,300 bucks for mine brand new 7 years ago and the machine is a beast but literally anti seize would cost them a penny or two to apply. Really hope I don't have to take it in - the replacement disk was like 30 bucks VS god knows how much to have a professional cut and press out if need be.

@Peppermint1 3 года назад

My friction disc failed after only 25 hours of use (5 years), the snowblower would not move in the slow speeds. The rubber on the friction disc is VERY soft, they call this 'smooth engagement' but what's not smooth is the amount it costs to have the snow blower sent to the dealership for replacement. In the past these discs would last 30 years+ . Go with Oregon discs, much stronger rubber. And now my auger bearing is failing. Bearing made in China.

@AriensChannel 3 года назад

Hi there. We're sorry you're dissatisfied with the performance of your unit. Please understand that friction discs are considered "wear" parts and will need regular replacement, depending on use. If you feel like your friction disc is wearing prematurely, please visit your nearest Ariens servicing dealer for a physical inspection. An Ariens dealer near you can be found using our dealer locator tool linked below: www.ariens.com/en-us/dealer-locator

@Peppermint1 3 года назад

@@AriensChannel It's because Ariens is following the market trend and puts cheap rubber on the friction disc. Everybody on forums is saying they have to replace the disc every 3-5 years, whereas in the past these discs would last 20-30 years. I have a suggestion: Ariens is still using a high quality paint on their snowblowers so they still care about quality somehow. Why not rising the price by $20 and use a better rubber quality? That way Ariens WILL stand out of the competition. With only $20 more. And for those who can't fire up their snowblower at the end of the summer storage, have a look here ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-FxZFRYCaEDs.html

@AriensChannel 3 года назад

@@Peppermint1 Thank you for your reply. We forwarded your comments to our RapidCare support team, which then consulted our engineering group. At this point, we'd like to get more details of your experience so we can examine it in greater detail to ensure our friction disc quality is up to standard. Please contact us using our support link below, explain the situation there and ask for Brent. www.ariens.com/en-us/support

@garyduran1 3 года назад

My Aries is weak on take off. Bigs down very easy. Is this video the problem? Thanks

@AriensChannel 3 года назад

Doesn't sound like that's a friction disc problem, Gary. Could be a number of things, but our suggestion is to have your unit physically inspected by an authorized Ariens servicing dealer. A dealer in your area can be found using our dealer locator tool linked here: www.ariens.com/en-us/dealer-locator

@garyduran1 3 года назад

@@AriensChannel thank you. I did replace the drive disc and the original one had hardly any rubber on it. It seems to be better now but I haven’t had any fresh snow to try it out. Thanks again.

@mk0246 3 года назад

I cannot get the wheel to come off this side. Any ideas on how to get it off? Can a wheel hub puller be used without damaging the key mech?

@AriensChannel 3 года назад

We're sorry you're having difficulty with that. We can't be totally sure without seeing the unit ourselves, but it sounds like this is a result of corrosion that partially fused the wheel and the axle together. If you can't remove the wheel, we suggest taking your unit to your nearest Ariens servicing dealer: www.ariens.com/en-us/dealer-locator If you do get the wheel off, remember to regularly lubricate the axle to help prevent this issue from happening in the future.

@mk0246 3 года назад

@@AriensChannel Mechanic told me he used a pickle fork to get it off. My model is a Ariens deluxe 28 model 921037. So.. pickle fork for the win. Buying myself a set today.

@AriensChannel 3 года назад

@@mk0246 glad you reached a resolution!

@Bwn-rl3gl 3 года назад

I tapped it with a hammer.

@Lylatoons 4 года назад

Looking for a friction disc for 921030, thanks in advance.

@AriensChannel 4 года назад

Thanks for the question, Rocky! That would be part number 04743700. Unfortunately, that part is out of stock at the Ariens online parts store, but you can ask your local Ariens dealer to source one for you. Links to both resources are below: www.ariens.com/en-us/dealer-locator parts.ariens.com/Ariens-Snow-Blower-Friction-Wheel-p/04743700.htm

@timb7775 2 года назад

I just noticed the claw on the sliding fork in my 1971 Ariens is cracked off, is this covered under warranty? It's only 50yrs old.

@88omarz 4 года назад

i own a 921044 and need to replace this, where can i get this and whats the parts number

@AriensChannel 4 года назад

Thanks for asking! The friction disc for a 921044 Deluxe 28 SHO Sno-Thro is part number 04743700. You can get one from your nearest Ariens dealer, or from the Ariens online parts store. Both are linked here: parts.ariens.com/Ariens-Snow-Blower-Friction-Wheel-p/04743700.htm www.ariens.com/en-us/dealer-locator

@88omarz 4 года назад

@@AriensChannel thanks for the swift response i cant seem to get the bearing off got the unit apart couldn't find instruction in manual or anything, Can't get the pinion sprocket off the bearing on the right side appears to be damaged in place which makes it difficult to impossible to remove the one on left came off very easily.

@rceme74 3 года назад

This is my second Ariens snow blower. My first was a small unit that worked like a big one. I changed the drive clutch assemble and all the belts and bearings to make sure my son would have no issues. I bought a new 28 Deluxe, first 2 years regular maintenance, then the Friction disk gave out, sent into the dealer for repairs and a good look over. Worked OK, but something was not right, I queried the dealer, he said sometimes they need to be work in. OK, never heard of this before, but you are the dealer. 3rd time out this year and no drive, called the dealer to pick it up and fix it. They charged me for another friction disk assembly and the labor as well as pick up and deliver. Is this normal??

@AriensChannel 3 года назад

Hi Stan, we're very sorry to hear about your experience, and we'd like to learn more about your experience to ensure this isn't a repeatable quality issue. If you like, please contact our support department linked below and explain the issue as you did here. One of our technical service representatives will follow-up with you to learn more about your unit, its use and provide some insight: www.ariens.com/en-us/support/contact-us

@rceme74 3 года назад

@@AriensChannel I took the unit back to the dealer, they tried to charge me for another replacement, however after a little discussion with the supervisor we came to an acceptable agreement. Now I have just learned my son's unit did the same thing, and he had his friction plate replaced last year. I am beginning to see a pattern, the original last 2 years very nicely, but the replacements had little serviceability. My unit is working very well for the past two snow dumping of 8 inches and 5 inches of snow.

@jimd2652 3 года назад

Where do I get a Service Guide ?

@AriensChannel 3 года назад

You can find one at the link below, Jim: www.ariens.com/en-us/manualsdownload Just keep in mind that a service guide may not be available for all units. In that case, the operator's manual should be able to help you through the procedure.

@jimd2652 3 года назад

Wow ! Thanks for the quick reply. That was really fast. Appreciate the link, unfortunately no service manual. Will work with owners manual and the RU-vid vids. Any way of eliminating the auto-turn ? Tried all adjustments, tire pressure, bolts connecting auger etc., to no avail. Like the machine except fighting to keep it straight.

@AriensChannel 3 года назад

@@jimd2652 You're very welcome, Jim! And no, the Auto-Turn feature cannot be modified. However if you're experiencing issues, there is an adjustment procedure that might help: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-fDVAnmvbovs.html

@jimd2652 3 года назад

@@AriensChannel Thanks for the link. Saw that one already. Did the adjustment, no change. Thanks again for quick reply though.

@robertisaac4357 4 года назад

You didn't clean the argur friction disc.........

@diverdave4056 4 месяца назад

WOW the video close ups of your hands wearing blue gloves made it very difficult to see what you are actually doing !

@Mark_Winters 3 года назад

Wow. With a tiny bit of effort, a few more pictures/different angles and that could have been really helpful. Lazy

@AriensChannel 3 года назад

Sorry about that, Mark. This was actually one of the earliest service how-to videos we piloted. Getting much better now with new equipment and new methods. Check out some of our latest videos to see where we're at now!

@christophers7059 2 года назад

I have a 2013 Ariens Platinum 30 SHO that I just bought used. Paid a LOT for such a model, relatively speaking to what I could have got for less. Thought process was it is a quality name and model. It looks new, hardly used. First time out the damn wheels don't engage enough to move the unit. Very disappointed; I could have stopped at any hardware store and bought a generic model brand new for the same price with no issues. This is a snow blower, it should not require maintenance like this for its basic operations at such low useage state. My God, there are units out there older than me still going. I like buying Ariens bc its local, but it will be hard to go that way next time.

@gramps5157 3 года назад

Poor lighting and you talked to fast and went to fast.

@AriensChannel 3 года назад

One of our earlier videos. A little rough back then, but getting better every day 😉

@GIBKEL 4 месяца назад

These friction discs had to have been defective. Not a single warning about faulty friction disc rubber peeling off issues. I had replaced it last year after many years of use. In less than a year, a new friction disc failed; peeled right off. It had to have been a defective batch as when I went looking for reviews of the Arien’s part, nearly all the reviews on their own site stated the same problem. Ariens doesn’t look after their customers and they are not cheap. Also, where I live in MT., their is no other choice. I’m buying a Honda next time if I have to drive 600 miles and spend twice the money as it is t worth the hassle , money or time to repair with faulty parts. Your company stinks as does the pot metal parts you build out of. You also miss tapped the spark plug threads to be at an unachievable for the spark plug wrench. I ended up having to grind down and existing wrench to change the factory plug. Garbage! The money saved on the front end of this piss poor design will be spent in winter hellscape when you have to repair it in the cold damp spring. Am I angry about this….damn straight!