How to Install 24v Cummins Fuel Injectors | Power Driven Diesel

Подписаться 131 тыс.

Просмотров 66 тыс.

50% 1

Baron returns to RU-vid to show you how to install 24V Cummins injectors. If you have a 1998.5 thru 2002 Dodge Ram 2500 or 3500 equipped with a 24V Cummins engine, this video is for you!
Get your own upgraded "Fueling Package" here: powerdrivendiesel.com/product...
Or if you just want a set of injectors and you already have a tuner like a Quadzilla, Edge, or Smarty, get your injectors here: powerdrivendiesel.com/product...
Find the best 24v Cummins parts at the lowest prices here: powerdrivendiesel.com/product...
Power Driven Diesel is a specialty performance shop engaged in the engineering and development of high performance turbo diesel technologies.
1 435 962 9555
powerdrivendiesel.com
/ powerdrivendiesel

Авто/Мото

Опубликовано:

1 июн 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 84

@CameronMatthews760 3 года назад

Recommendation on where to buy injectors from?

@pddofficial 3 года назад

A link for injectors is in the description, obviously we are biased but powerdrivendiesel.com/product-category/dodge-ram-diesel/1998-5-2002-2nd-gen-24v/24v-fuel-injectors/dodge-ram-cummins-1998-5-2002-2nd-gen-24v-fuel-injectors-budget-builder-24v/

@CameronMatthews760 3 года назад

@@pddofficial thoughts on reman for people on a budget?

@pddofficial 3 года назад

Bare nozzles are cheaper, we sell them and they work great!

@njdevi11 3 года назад

@@pddofficial recommendations for a pop tester setup for installing nozzles for the slightly advanced home gamer?

@andrewb9708 Год назад

@@njdevi11 There's quite a few options, they're typically $100-$400 for the testing unit. My local (and highly trusted) diesel shop charged me $50 to pop test and balance my injectors (brand new Bosch 245hp HO). Of course, all the installation work was done by me. It's not that bad of a job, it took me four hours to replace the injectors, cross over tubes, and do a valve lash adjustment.

@rubikrawler 3 года назад

I just installed my PDD 24v injectors on the Fummins and it’s running great. Looking forward to grabbing a quadzilla from you next.

@pddofficial 3 года назад

Sounds great!

@KREperformance 3 года назад

Best way I found to get the copper washers out of the injector bore is use a flathead screw driver because it has a slight taper. It’ll get the washer hung on the taper when you give it a few love taps and she’ll come right out

@njdevi11 3 года назад

Fire arm cleaning kit. Those copper brushes work great. I think .308 works best.

@niceguy4928 3 года назад

Thanks for the videos 👍🏻 wishing I had a Cummins.

@Rayraysrides 3 года назад

content is always great!

@devinmanderson 2 года назад

Tech tip: crows foot or offset wrench really helps with getting injector lines and any other tight space lines off. Use them all the time to pull hydraulic lines off valve bodies.

@digitalmuzik8086 Год назад

Thx for tip. having this issue atm.

@devinmanderson Год назад

@Digital Muzik808 if all else fails harbor freight cheapo wrenches and a torch bend them mofos to fit...not you have a special custom tool welcome to mechanicing

@jrod5045 3 года назад

Woooo finally doing a series for VP44S!!!

@pddofficial 3 года назад

Of course!

@jimg2885 Год назад

Thank you for the video. Great info. Just subscribed and look forward to watching more of your videos.

@pddofficial Год назад

Glad we could help comments like this is why we do it!

@jimg2885 Год назад

@@pddofficial Just ordered my injectors after watching your video. Will be watching it again when I start the install. I like how you explained the process. Again Thanks

@pddofficial Год назад

@@jimg2885 thankyou so much for showing your appreciation. doing these videos is very time consuming but comments like yours make it all worth it. Baron

@ericbenttech2234 8 месяцев назад

Thanks for a very professional vid!

@pddofficial 8 месяцев назад

Glad you liked it!

@electricamir248 Год назад

Great video. Thank you.

@pddofficial Год назад

You are welcome!

@davidspeyers5740 3 года назад

This guy has done that a few times... his hands were flying!

@astoltzfus4 3 года назад

I saw another PDD video and thought, "Yes! Finally the UCC video!"

@Mikheno 3 года назад

Just did this awhile back to install Bosch RV275 Injectors. Nothing more than common hand tools and a few hours of your time. I replaced the O-rings in the fuel tubes and adjusted the valves while I was in there. Make sure you get the copper washer out when pulling the old injector. You will probably need to leave a few injector lines loose when you start up for the first time. This will bleed the air out and save your battery from 20 minutes of cranking.

@pddofficial 3 года назад

Great to hear and good tip!

@1matdad362 6 месяцев назад

CANNOT BELIEVE THAT YOU DIDN'T COVER THE OPEN INTAKE ! Otherwise good Vid!

@lastkings6209 3 года назад

Can y’all do 6.7 Cummins next please?

@chadhester265 3 года назад

Keep em Cummins

@elemen7713 2 года назад

i just did my injrctor and now my truck is rought at idle is sound like is missfiring i know this truck dont have spark plug or glow plug but that the only way i can tell u how it sound like any help please

@prashantverma6811 7 месяцев назад

Thanks

@pddofficial 7 месяцев назад

Welcome

@Frankstgeorge88 2 года назад

How about one for a 5.9 common rail

@anaconda7540 Год назад

In process of doing injectors on my 06 5.9. Everything went together great I never cleaned out injector bore bc they looked shiney. Now I’m seeing guys are spraying and scrubbing out with a brush. Do I need to pull them back out and clean out bores with a brush?

@pddofficial Год назад

No you should be just fine.

@hambuga69 Год назад

Seen this video quite a few times. I’m about to put some 7x0.010 vco injector nozzles on my 24v. Wonder how bad egts will be with stock hx35.

@pddofficial Год назад

will need to watch the gauge for sure.

@Mike-qu8bh Год назад

If you’re upgrading injectors, to a bigger injector, do you need to upgrade the connector tubes as well?

@pddofficial Год назад

No not unless you are running 7x.013 and bigger

@blackout394 Год назад

Just installed the injectors from your PDD 24v 475hp fuel kit. Not sure what went wrong but got it to start up and it runs rough. Rough idle and rough acceleration until you get pretty high in the rpms. I bled the injectors good enough to my thought but could air still be trapped in the system? Should i try to re-bleed them again?

@pddofficial Год назад

Sounds like cross over tube not seated. Redo them and see if that fixes it. Please feel free to call our tech support team they would be glad to help you. 435-962-9555

@1matdad362 6 месяцев назад

APOLOGIES, NOTICED YOU FINALLY COVERED THE INTAKE, 👍

@jimg2885 Год назад

Question for you, do you not install new gasket at the air horn and valve cover? Did not look like it in the video. Thanks for your input.

@pddofficial Год назад

At the valve cover it is usually not necessary as the o ring rarely goes bad as for the intake horn depends how it comes out

@jimg2885 Год назад

@@pddofficial Thank you so much for the reply. You're awesome and again best video that shows the details. You are the most informative and I really appreciate a person that takes the time to do it right. Again ThankYou

@pddofficial Год назад

@@jimg2885 love to hear it!!

@bluebird5100 3 года назад

What did you spray into the injector lines to clean them?

@pddofficial 3 года назад

brake clean and shop air

@riverguy988 6 месяцев назад

Do I need to buy brand new cross over tubes to go with the new injectors? Can I just inspect my old ones?

@pddofficial 6 месяцев назад

If the tubes are not damaged yes you can reuse them.

@ArturoGarzaID 2 года назад

4:38 what were you unscrewing 4:52 what were you pulling out, what did you drop?

@pddofficial 2 года назад

At 4:38 he is pulling out the hold down bolt for the injectors. At 4:52 still pulling bolts on the hold down but he set the impact down and the socket fell

@hounddog8862 2 месяца назад

Problem I’m having is high pressure on the fuel return to the fuel tank, there is vapor fumes and when filling the tank engine running it’s pushing fuel out . Any suggestions on why

@pddofficial 2 месяца назад

Could be a restricted return or the tank vents clogged

@hounddog8862 2 месяца назад

@@pddofficial all seams free of restrictions or clogs, I believe there is a bad o ring on one or more injectors causing the pressure to push back towards the return

@johnv.v.9716 3 года назад

Now you guys should do the proper way to do head studs. Do we need to pull the head and install a head gasket and adjust vales? By the way where is Todd, I miss Todd.

@drake_24v_hawkins 3 года назад

Do your headstuds one at a time, I do it in the torque sequence for the head, never bad an issue. Done it on several trucks.

@drake_24v_hawkins 3 года назад

100% adjust valves. Anytime you do anything with headgasket/torque the cylinder head, easy to do

@doorymcfly3488 10 месяцев назад

Is it uncommon to just replace the o rings and clean the injectors out because they are leaking?

@pddofficial 10 месяцев назад

Yes they should be pop tested to insure proper working order.

@jacobltrotter 3 года назад

Made me nervous on that hold down bolt I snapped mine off in the head and was using a torque wrench lol

@Joker-rx6xw 3 года назад

Where can I get me a set of those fancy coppers at?

@pddofficial 3 года назад

They come in our install kit

@rrr3r2 3 года назад

We’ve all forgotten the connector tubes at one point

@evangriebe3861 8 месяцев назад

thanks for showing how you got the 6th injector line off 🤦🏻‍♂️

@pddofficial 8 месяцев назад

No problem 👍

@loopernite5747 6 месяцев назад

Get your hands dirty its not that hard figure it out 🤦🏽

@mmmontague9048 3 года назад

Lol this would have been good 3 days ago when i did mine oh well lol

@pddofficial 3 года назад

Dang guys forgot to upload this video, it's been ready for a few weeks now.... sorry about that!

@mmmontague9048 3 года назад

Haha all good its a great video gives me reassurance i did everything correctly

@dixiemae5042 3 года назад

Behind the curve today 😑

@pddofficial 3 года назад

Yep, you were asleep and got treed! LOL

@benitogordito5676 3 года назад

Slow. Down.

@wizardsleevesteve5256 3 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hEcuVR2vHwM.html

@zslemp 3 года назад

hard to take yalls advice when everything yall build blows up

@pddofficial 3 года назад

We've never blown up a mild/moderate build, kinda like what most guys see day-in/day-out. The 2000+ HP stuff commonly has failures, parts breakage, etc.... BUT that big power carnage is hidden from Joe Public by most performance companies, we simply choose to share it so everyone can get an insider's viewpoint. If you don't like the free content, feel free to leave!

@zslemp 3 года назад

@@pddofficial just don't forget your throttle return spring and blame it on the pump builder. And don't show Joe public tods booger welds y'all do.

@DOAD_Diesel 3 года назад

@@zslemp it’s almost comical seeing people like you comment. Never built a 2000+ hp truck yet know everything about it and knows how to do it without failures. If you had half a clue why these engine fail under a high torque spike or why their last engine blew up the way it did your comment wouldn’t look so ignorant.