HOW TO Install a Fleece Cheetah 6.7L Cummins Turbo

Подписаться 120 тыс.

Просмотров 59 тыс.

50% 1

🔧 Watch Wade install a Fleece Cheetah turbocharger on a 6.7L Cummins. This is a drop-in replacement turbo for #diesels. It comes with a #fleece Performance Engineered compressor wheel and high flow Cheetah turbine wheel. This drop-in replacement turbo is guaranteed to enhance your driving experience. You’ll enjoy the spool up and throttle response of a small #turbo and still get the big top end power you're looking for. If you are towing during the week, and sled pulling on the weekend, the Cheetah is just the ticket.
Powerful Yet Responsive! These #turbochargers spool like stock, thanks to the variable nozzle technology (VNT) which allows the turbo to act smaller upon spool-up and then open up to flow more exhaust on the top end.
Fleece Cheetah Turbos Features:
✅ Forged Milled Wheels are Stronger than Billet
✅ Faster Spool-Up
✅ Increased Throttle Response
✅ Broader Torque Curve
✅ 2.5" Work Stock Legal
✅ The Ultimate Drop-In Replacement Performance Turbocharger
🔥 Want a Fleece Cheetah Turbo? Order One Today!
www.thoroughbreddiesel.com/fl...
✅ Check Out Our Other Install Videos Here:
• Installation Videos
⚠️ Saving Diesel Lives! Check out our online store for performance products at:
www.thoroughbreddiesel.com/
☎ Give us a call for IMMEDIATE FREE ADVICE: (859) 737-4966
🎉 Please remember to SUBSCRIBE, LIKE, and COMMENT if you like our videos! It really does help us out! Thanks for the support!
ru-vid.com...
❤️ Join Our Diesel Community ❤️
● FACEBOOK: / thoroughbreddiesel
● TikTok: / tbreddiesel
● INSTAGRAM: / tbreddiesel
● TWITTER: / tbreddiesel
● PINTEREST: / tbreddiesel
● BLOG: www.dieseladdict.com/
● SNAPCHAT: tbred_diesel
Chapters
00:00 Introduction
00:51 Install time (6 hrs) & Difficulty (8)
01:33 Installion begins (make sure to disconnect your battery cables)
01:53 Draining the radiator
03:53 Removing air intake
06:14 Removing air intake tube
08:49 Removing inner cooler tube
11:43 Removing coolant supply to turbo
12:16 Removing oil supply line
13:46 Explaining the wires going to the turbo
18:07 Removing the wheel well
19:28 Removing electical connector from the actuator
20:49 Removing the knox sensor
24:45 Removing exhaust from turbo
25:54 Removing brackets to down pipe
26:59 Removing turbo elbow to down pipe
29:58 Removing turbo oil drain
32:44 Lifting the engine
34:50 Removing the coolant line
36:45 Removing the bolts to the turbo
37:43 Positioning the old turbo for removal
40:00 NOW remove the battery
40:22 Removing the old turbo
43:53 Prep-work before installing the new turbo
47:04 We strongly suggest using a new Fleece oil drain tube
48:44 Removing old oil drain tube
50:24 Bolting new turbo into place (don't tighten all the way)
55:42 Attaching the coolant line
56:57 Tighten nuts on turbo now
58:00 Installing Fleece's flexible oil drain tube
01:00:22 Adding the exhaust elbow to the turbo
01:03:37 Re-installing the knox sensor
01:07:30 Pre-oil the turbo & recommend oil change when installing a new turbo
01:08:55 Installing oil supply line
01:10:19 Installing coolant supply line
01:11:51 Re-attaching intercooler pipe
01:15:19 Re-installing air box/filter
01:16:52 Re-installing solenoid
01:18:17 Re-installing turbo intake tube
01:21:14 Re-filling the coolant
01:22:41 Ride-along and summary
#fleece #turbochargerworld #turbo_xtreme #turbolife #turboprop #thoroughbreddiesel #whistlindiesel #dieselpower #diesellife #dieselporn #truckporn #cummins #whistlindiesel #cumminsdiesel #powerstroke #powerstrokediesel #duramax #duramaxdiesel #diesel #truck #trucks #truckproject #truckrepair #fordtrucks #fordtruck #ramtrucks #ramtruck #dodgetruck #isolator #dodgetrucks #chevytrucks #chevytruck #gmc #gmctruck #gmctrucks #fordtrucks #dodge #ford #chevy #shorts #short #shortvideo #youtubeshorts #youtube #youtuber #whistlindiesel #turbolife

Авто/Мото

Опубликовано:

20 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 111

@thoroughbreddiesel Год назад

🔥 Want a Fleece Cheetah Turbo? Order One Today! www.thoroughbreddiesel.com/fleece-cheetah-turbo/

@matt3608 Год назад

This is what kids these days need to learn, not 3,479 genders

@GregElliott-uz6sp 3 месяца назад

can't thank you enough for doing this video, saved me $3000 dollars by doing it myself! i owe you a beer!

@thoroughbreddiesel 3 месяца назад

You're very welcome!

@elicampbell2786 Год назад

Wish this video was up a few days ago. Just replaced my turbo on 2016 RAM 3500 with a tow master from Thoroughbred Diesel. Had to fumble my way through it. Got it done but I will say the fleece cheetah drain tube is an absolute must have.

@thoroughbreddiesel Год назад

Shoot. Well, glad you got done.

@AquaticLogic Год назад

Thanks for the upload guys gonna be a big help. That poor Cummins still has an ERG on it, hopefully one day it can be liberated 👍🏻

@thoroughbreddiesel Год назад

You're welcome!

@user-sk4zb2ni6l 6 месяцев назад

That is a good video and is very descriptive! Thank you!

@thoroughbreddiesel 6 месяцев назад

Glad it was helpful!

@brysonrowe2262 6 месяцев назад

You are the man. Video really helped me with my install. Thanks a lot.

@thoroughbreddiesel 6 месяцев назад

You're welcome!

@HerbertPrince 4 месяца назад

Wade is correct. This Fleece Cheetah is what I went with with new tuning. It will awaken when I put it to the floor.

@jameskeen8063 11 месяцев назад

Good job Wade, have all new respect for you. Everything you said is true Put performance exaust manifold on my 2018 Ram 3500, much easier with emissions removed.

@POOLGUY100 6 месяцев назад

Re:Nox sensor. Thanks for the video. It is very helpful. The thing is, I sat down for a minute and realized there was no need to remove the nox sensor as i have 410km on my truck, so it's tight. Just take the whole elbow out with the sensor/cable and move it off to the side. There is enough cable once you cut the zip ties that it can sit on top of the steering linkage.

@thoroughbreddiesel 6 месяцев назад

Thanks for sharing.

@ontariocashcropfarmer4955 Год назад

Be nice to see you put one of those fleece cheetahs on your old Duramax, I've got an 02 lb7 was thinking about putting a cheetah on🤠😎👍

@thoroughbreddiesel Год назад

Maybe in the future.

@ontariocashcropfarmer4955 Год назад

@@thoroughbreddiesel I'll be watching for it 👍💪👌

@jakemerelli3934 Год назад

Just finished getting mine out. Watched this video step by step and followed to a T except that I did remove the battery tray and therefor didn't have to disconnect the alternator. I also opted to remove the coolant line from the block instead of dealing with the tight area under the turbo near the oil drain tube. Can't thank you guys enough for this video! New fleece goes in tomorrow morning 😃

@thoroughbreddiesel Год назад

You're very welcome!

@Bigdaddyy69 8 месяцев назад

Did you throw injectors in your truck or are you running stock injectors?

@timbrunner8050 28 дней назад

Great video!!! watched it a few times and just finished swapping mine out. I saved a little time by not removing the NOX sensor, just undo the 2 clamps and take the elbow out the side and set it on the suspension. the only other thing I did different was the bottom cooler line, if you massage the heatshild a little, you can get a 7/8" socket on it to undo it. all in all, one of the best if not the best video for this swap!! thank you!!

@thoroughbreddiesel 25 дней назад

Glad it helped! Thanks and you're welcome!

@joekestner8354 7 месяцев назад

Great video helped so much. But, I found if you remove the compressor housing you have good access to the lower lines and you don't have to raise the engine 2015 Ram 2500

@thoroughbreddiesel 7 месяцев назад

Thanks! Good tip!

@jacksondaniels8169 Год назад

Great video, going to be doing my turbo soon. Recommend linking your products and listing your tools used used in this video. It makes it easier to locate them.. As I cannot locate the down pipe gasket at 1:01:30 you spoke of having on your site.

@thoroughbreddiesel Год назад

Give us a call at 866-380-3068.

@mylesm7947 6 месяцев назад

Use a bore scope to show the hidden work

@brentmcmahon8188 Год назад

I want you to do a second Gen swap with a Sneed Speed exhaust and a cheats turbo on my 05 3500 6 speed manual 4 door long bed dullay and it is used to haul a 10.6 Bigfoot truck camper so let me know I will pay for all parts and you supply the labor. This will be a good video for your customers !!

@brentmcmahon8188 8 месяцев назад

Wade I’ve been watching your videos for a long time because you use to have brown hair when to gray and now it’s white, this job is tuff on a old dude . Ha Ha and Iam 68 and tiny bit of gray .

@carlosmerino5547 7 месяцев назад

My Brother how are you doing there with your new Dodge , l am impressed how well and details you explained heviting on, l thank you very much , l do have 1999 Dodge Diesel 2500 , l am going to put a turbo like one but much older with not Egr , God bless you my brother your the best to explain step by step uninstall to put back together l thank you very much for your well video!

@thoroughbreddiesel 7 месяцев назад

Thanks and you're very welcome!

@Legoinry 7 дней назад

I feel like those manifold stud holes are to tight on all of my imports that have had that issues I take a drill and clean the holes up to get rid of the resistance, also yes I own a 2013 cummins so what I wonder would there be an issues with doing the same on the manifold of the truck seems like it would make siding the turbo back on and off much easier

@TheMinnow101 7 месяцев назад

6 hours to install and a difficulty of 8 out of 10 is not in my thinking a “drop in” part.

@The412Devil 2 месяца назад

I would not call that a 8 out of 10 job. 8 would be like a cylinder head. 10 would be a motor disassemble.

@Lparton1313 10 месяцев назад

So I put this turbo on my 2018 ram. Everything went smooth, Turbo works great. I installed the fleece drain tube with no added gasket at first( looked like it’s what you did in the video). About 5k miles it started leaking oil. Yesterday I took it off cleaned everything up and added a gasket with a fine line of RTV( used high temp red) … still leaking. I’m going to attack it again this weekend. Any advice as to why it could be leaking? Was going to try a new gasket with oil resistant RTV.

@thoroughbreddiesel 9 месяцев назад

Same thing happened to us. The drain tube does not require another gasket, as there is a recessed o ring in the flange. The first kit we had the bolts in it were too long to make a good seal, you might want to check bolt length. If you need help on this just give us a call.

@user-ki7hu8ub8u 11 месяцев назад

Can you show how to install it in the 5.9 Cummins

@skidoopwns 6 месяцев назад

@thoroughbreddiesel did you do anything special for first startup with the new turbo? Some recommend unplugging the injector harness and turning the engine over multiple times for 10 second intervals to get oil pressure at the turbo before first startup. Then plug injector harness back in and start the truck. What do you typically recommend?

@thoroughbreddiesel 5 месяцев назад

We recommend pre oiling the turbo, we also recommend an oil change when changing a turbo. And for that, we change the oil right before changing the turbo, so that the truck doesn’t have extended times without lube.

@Ahmed.45 7 месяцев назад

Good evening sir. First, thanks for an incredibly useful video. I'm at the point of lifting the engine up 1" on the passenger side to clear the turbo studs and found that the engine does not pivot upward. Engine mount bolt has at least 1/8" of clearance on each end. What are the possible causes? Thanks in advance for your reply!!!

@thoroughbreddiesel 7 месяцев назад

That is odd. I would suggest loosening the drivers side as well.

@Ahmed.45 7 месяцев назад

Thanks for the answer! Turbo installation was very successful, thanks to your video, no leaks, great performance etc. FYI- I loosened the transmission shock mount bolts and it came right up. My next move would have been the driver side mount bolt as you suggested. Thanks again! B

@rajunace Год назад

Followed this tutorial, and came out just flawless, took me about 7 hours total. I do have one question, at 1000rpm I have a rough idle, any ideas?

@thoroughbreddiesel Год назад

Any codes? Check codes and look at actual vs. commanded fuel pressure. I don’t think its turbo related but we can help you figure it out.

@rajunace Год назад

@thoroughbreddiesel no codes. It's a 18, so I had to order gateway bypass, to check injectors and calibrate vgt module, should be here this weekend

@rajunace 11 месяцев назад

Recalibrate VGT, did a kill test and number 1 was no change to idle or 900RPM Is there anything else I can check before I tear down, to make sure u replace what needs to be done

@brentmcmahon8188 2 месяца назад

Man there is a ton if junk under that hood . Iam sure glad I bought a new Dodge in2005 and there is nothing under my hood is a hard pulling 5.9 been a great truck 1 ton 4 door long bed dullay 4x4 factory 6 speed manual and manual 4x4 selector Laramie.

@stephenbaker7960 2 месяца назад

Looks like a nightmare. 64.5 sxe with t4 mount went into my obs 7.3 way easier

@zacedward1 Год назад

Thanks so much for the video I have a 09 3rd gen Cummins is the install the same and does that turbo work for mine or just the 4th gens thanks so much

@thoroughbreddiesel Год назад

Here ya go www.thoroughbreddiesel.com/351-0712/

@thoroughbreddiesel Год назад

Install should be similar

@zacedward1 Год назад

@@thoroughbreddiesel thank you so much I greatly appreciate it

@thoroughbreddiesel Год назад

You're welcome!

@TD-cm7vw 6 месяцев назад

Is the fleece available in the 23 models, and would I need any additional tuning even though it’s just a drop in vgt?

@thoroughbreddiesel 5 месяцев назад

Give us a call 1-859-737-4966.

@rogerstewart5140 10 месяцев назад

So if you do a 2nd gen swap on a 18 ram 6.7. What price range would you be at all in?

@thoroughbreddiesel 10 месяцев назад

Give us a call 866-806-6142.

@garysmith643 6 месяцев назад

Was wondering advantages of this turbo ? Hp ? Torque? Website says "increase performance " thanks

@thoroughbreddiesel 5 месяцев назад

Truck setup will determine the HP capabilities of the Cheetah. This one, for the 13-18 Dodges will support up to 700 HP (with the right modifications).

@eddiebelt8582 10 месяцев назад

i think bringing the turbo from thr bottow is easier

@larryhaupert7305 Год назад

What is the advantage of changing out from stock turbo to a cheata?

@thoroughbreddiesel Год назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-YiwItqXuySI.html

@adamstehl7135 5 месяцев назад

Have a stock 16 ram 3500 if I upgrade to this turbo do I need to reprogram, tune, flash anything? Have a actuator code and figured I'd up garage the whole thing not much more to do so

@thoroughbreddiesel 5 месяцев назад

No reprogram necessary with this turbo and that’s the one of its best features. But the truck runs so much better with tuning that really takes advantage of the performance turbo.

@thoroughbreddiesel 5 месяцев назад

No, it is plug and play.

@Two_skoops 2 месяца назад

What size I/D for the hose to connect to the drain tube on the radiator? for a 2019+

@thoroughbreddiesel Месяц назад

I think I used a 5/16 line there.

@mmillich87 5 месяцев назад

Been trying for an hour to get the bolts in on the bottom of the turbo to the fleece oil drain tube. Only way I can see to line up the bolts is under the truck with an extension. If I remove the passenger front tire will I be able to access it?

@mmillich87 5 месяцев назад

Do you have the engine lifted still when you install the fleece oil drain tube?

@thoroughbreddiesel 5 месяцев назад

Extension and a universal socket works the best.

@jellymolina6972 Год назад

Question I have a 2018 ram 2500 mega cab it’s already has tunes is there anything that I have to change as far as parameters?

@thoroughbreddiesel Год назад

Tuning is not required.

@jellymolina6972 Год назад

@@thoroughbreddiesel thanks

@brandonhirdler 4 месяца назад

fleece speed sensor is a low cost part? It's $140.00!

@jaredc9462 8 месяцев назад

Do you have to Jack or lift engine on a 2019 ram??

@thoroughbreddiesel 7 месяцев назад

The turbo is angled on those trucks and doesn’t have to be lifted.

@brentmcmahon8188 2 месяца назад

What kind of your battery operated ratchet what brand is and do you like it ?

@thoroughbreddiesel Месяц назад

It’s a snap on 3/8 ratchet 14.4 volt. I really do like the ratchet, but I haven’t had very good luck with these batteries. I know a lot of guys like them but I haven’t been very impressed. Great ratchet though.

@michaelfraser2614 Год назад

I was looking at the 3000 because you put it on one of the trucks I got on the web and it has a lot of bad reviews it looks like 90% of people likes the s300’s what do yea think

@thoroughbreddiesel Год назад

I am very happy with this turbo on my truck, for what I do at less than 400 horse, it does well.

@SuperWD9 11 месяцев назад

What's the part # for that shallow 1/4" 10mm wobble?

@thoroughbreddiesel 11 месяцев назад

Snap On TMUSM10A

@SuperWD9 11 месяцев назад

@thoroughbreddiesel thanks, ordered the whole set!

@matthewdouglas4817 4 месяца назад

Does the fleece cheetah come with a CARB sticker for us that have to smog?

@thoroughbreddiesel 4 месяца назад

Both models of the 6.7 Dodge Cheetahs have EO numbers and come with the sticker for your truck.

@martinchavez246 Год назад

Is lifting the engine absolutely necessary? Could you put a tool list needed for this

@thoroughbreddiesel Год назад

Lifting the engine is a must unless you jack up the motor from underneath. You will need to do this so the turbo clears the studs when it comes out.

@jacksondaniels8169 Год назад

@@thoroughbreddieselI’ve seen videos that did not do this step.. Going to be working alone so anything to make this easier the better.

@kx125rcr21 11 месяцев назад

The only way to do it without pulling the manifold and the turbo is to lift the motor. If you take the manifold out and want to deal with the 12 gaskets that are behind it also, you don't have to lift the motor.

@Kamikazekyle05 8 месяцев назад

It’s easier to pull the manifold with the turbo as one unit.

@mylesm7947 6 месяцев назад

Is there a better intercooler tube available

@thoroughbreddiesel 5 месяцев назад

Yes, we offer upgraded intercooler tubes for these trucks from some great manufacturers. Give us a call.

@mikezaloudek4893 Год назад

Was that dent in the intercooler pipe supposed to be there?

@thoroughbreddiesel Год назад

Yes, that is factory clearance for the intercooler pipe. Crazy.

@mikezaloudek4893 Год назад

@@thoroughbreddiesel that’s horrible. I though for sure it was damaged.

@kellydavis4954 18 дней назад

what a nasty beach

@TwitterSucks-yl1ir Месяц назад

Hey Wade, only wanted to punch you a couple times 😉 for helping give me the confidence to tackle this project… definitely learned to listen carefully to your warnings…my favourite new sayings are uga duga and grab it and growl…kidding aside, thanks, best video on the net…

@thoroughbreddiesel Месяц назад

This made my day. Thanks! Glad I could help!