HOW TO REPLACE A TURBO - STOCK or UPGRADED

Подписаться 81 тыс.

Просмотров 155 тыс.

50% 1

Looking to Upgrade or Fix Your Turbo? Follow Our Step-by-Step Guide! Join our Community of DIY'ers: ru-vid.com... Follow us on Facebook for More DIY Goodness: / e.doityourself
Follow us on Twitter! / everything_diy
Check out our Pictures on Instagram! / e_diy
Parts Used:
- OEM K04 turbo
- New OEM crush washers for turbo coolant and oil lines
- New OEM gaskets for oil drain line
- Zerex Asian coolant
Tools Used:
- Ratchet
- Various sockets
- Extensions
- Flex ratcheting wrenches
- Jack
- Jack stands
- Pliers
- Flat head screw driver
- Torque wrench
- PB Blaster
- O2 sensor socket
- Drain pan and funnel
The DIY Rep in this Video is Ally!
To send letters, products for review/use, other correspondence - please use this address:
everythingdiy
P.O. Box 186
Pasadena, CA 91102
FTC Disclaimer:
All products mentioned were purchased by us. None of the companies mentioned are paying us for this video. All opinions are our own.
Other Disclaimers- Everything you do is at your own risk. Everything DIY or its affiliates are not responsible for any personal injury or property damages incurred.
SAFETY FIRST EVERY TIME

Авто/Мото

Опубликовано:

13 апр 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 255

@HUBBABUBBADOOPYDOOP 8 лет назад

Watching this, with both laying side by side- brought back a funny-but-not-so-funny memory: guy was "changing" turbo (not upgrade) and after a few beers and shots with his "Garage Buddies" ended up stupidly re installing the *same* seized unit again.

@joemilton7552 8 лет назад

Happened to a "buddy" of yours, I gotcha ;-)

@HUBBABUBBADOOPYDOOP 8 лет назад

Joe Milton Not me. Never turbo'd, don't drink.

@enriquerivera4909 5 лет назад

Stay thirsty my friends

@danielgabarron8578 11 дней назад

I did that last week with my sunroof gasket

@19MarkDavid 7 лет назад

Never seen an engine dismantled and reassembled with such clean hands, clean engine compartment without one broken nail or even a smudge on that a nice shirt and top outfit.

@JeffBNH 3 месяца назад

A very good video, all be it, staged to look like she did all the work! But well done, none the less!

@robw1031 8 лет назад

I thought teaching my daughter to drive a stick and change a tire was accomplishment.

@Notcminecraft 4 года назад

@Joseph Gross jack up the car than its 5 nuts.... i could do that at 10 years old

@devjlboy 3 года назад

Joseph Gross I don’t understand how people don’t know how to change a tire. I knew how before I ever saw anyone do it, common sense really. If you know how to screw a bottle cap on and of you can change a tire.

@LSWhat87 3 года назад

Just pulled my turbo on my '09 MS3 today following your guide. Clean tutorial and straight to the point. Thanks!

@tedjohnson64 6 лет назад

Wow, that was one of the best how-to videos I've seen in a long time! I'm very impressed by the high quality video shots, and the rigorous documentation of all torque values and tools used. I really liked the reassembly montage as well. Amazing (scary) keeping track off all the parts, hoses, connectors it takes to access the turbo.

@cwatson42785 7 лет назад

I have insane amounts of respect for this lady. That is keeper of a wife if I've ever seen one. Big props!

@13SyNtaX37 5 лет назад

I just replaced my first turbo today following your video on my pu, thank you for the detailed instructions and editing

@gonesailing 8 лет назад

Wow. That is quite an involved strip down for the turbo replacement. Gives me an idea of what's involved should the Audi go bad. Thanks for the super helpful and detailed video!

@scotthester2189 Год назад

Best video yet for Mazda turbo replacement. Great job.

@wumboptimus 7 лет назад

Everything follows up, I watched this video twice when I installed mine and is awesome!

@toberkitty 8 лет назад

Wow, good on you for replacing your own turbo! On the only turbocharged car I had (Shelby GLHS) it was easier to remove the head and exhaust manifold/turbo assembly together as a unit, and it was a PITA, as you can imagine. I can't get over how clean the engine bay is in your car too. I wish I could keep mine that clean. Great vid!

@MISHASHOOTS 5 лет назад

thanks a lot for uploading this! I got 08 mazda cx7 and the turbo went out on it, and your video is gonna be the same guide for my car!

@Fivallify 5 лет назад

great video, I’ve owned my mazdaspeed6 for a couple weeks now, stock ko4 has seen better days and is smoking on most starts and cool downs, I am swapping a bnr s3 way quicker than I imagined. I haven’t been able to find any helpful videos in the mazdaspeed platform and this was by far the best. kudos to you for being a girl and owning a speed👍🏻

@bravalin8872 8 лет назад

the MZR engine is such a pain in the ass to work on. The harness is a nightmare. I love my speed 3 but god damn!

@adamjeppson7677 6 лет назад

Well done on the install and editing video. Best video I've found on the Mazda turbo.

@broGabiza 6 лет назад

Great job dear! So good to see a lady getting down to some serious business. Awesome💪👍

@jamesgreen3901 4 года назад

Wow your engine bay is so clean kudos!

@davidsullivan7867 7 лет назад

I envy how you're able to work on this car without getting dirty! Excellent video as always.

@adrianslk1 3 года назад

I think its imposible

@ricardoluna9369 8 лет назад

am glad I found your channel I got a ms3 as well, now I know how to get stuff done by myself thanks for this :D

@patrickwills8984 3 года назад

Almost 100k on my 2012 and my turbo just went out. This was a great find, thanks!

@xMattJew 8 лет назад

Awesome video! I'm in the process of doing exhaust manifold because I have a leak, not sure if it's the manifold gasket or the manifold itself but those 4 bolts from the manifold to the turbo were loose, i tightened them and it's not as bad as before but still there and I can still notice it. They were easy to get off and here you are saying they're super tight. Then when I went to torque them down 45-50 ft-lb, I was scared I was going to snap them so I'm not sure if its that that's loose and thats why I have a leak or if it actually is the manifold/gasket. Any advice/input on this would be great! I love watch your guy's videos, always super informative and easy to follow!

@stevenoliveroliver4950 5 лет назад

you are awesome! I'm being changed 850 for a recon and they have had it just over 3 weeks....

@ErnestoValdezJr 8 лет назад

Great video. I found it looking for any help I could find with replacing the turbo in my 2008 CX-7 which failed yesterday. With our cars both being Mazda's do you think the procedure is pretty similar? Also, did you use a maintenance manual and if so which one? Also, about how long did it take to do the work?

@TMERUNNR 8 лет назад

What band was that playing at the end of the video? Great music! I've been learning a lot from your channel as I'm a new MS3 owner, thank you and keep up the Fantastic Work!

@samgillham4243 7 лет назад

Do you know? I find watching these videos on cars is much more informative and much easier to understand! Plus the presenter is good on the eye also, bonus.

@Darus2013 4 года назад

Fantastic! Now to attempt this on my rusty bolts :( great video how many hours did it take you?

@jewllake 8 лет назад

very nice detailed videos. Keep them coming.

@AnthonyAwada 6 лет назад

That vacuum hose in the back that you removed when taking the intake off (one near the turbo). Where does that go to? Thank you.

@debraj.billings3011 8 лет назад

Wow I can't believe you did that yourselves....Damn good video! Thanks for sharing!

@wyattoneable 8 лет назад

A very well organized video and you did a good job explaining the process.

@Fixing_Everything. 8 лет назад

Yes great video and well done to you for doing this job. One question. I have been working on cars / vans / HGV's since the 1970's and in all my years I have Never worked on a car and not ever gotten away without getting covered in... yuk, oil, crud. You say the turbo sized but dam... that is the cleanest turbo and cars engine bay i have ever seen. Keep up the good work.

@weykon 2 года назад

True.

@johnlukic986 6 лет назад

Thanks heaps for this video Just doing my Cx7 turbo And the video is very helpful.

@xzaviermartinez7825 8 лет назад

Just happened yesterday thanks for this!!! 👌👌👌

@johnlu1527 8 лет назад

I Just wanna say, Good Job to you and Steve

@jorgehumbertoreyes9616 6 лет назад

Excellent video, using this video I was trying to replace the turbo in a Mazda CX7, I bougth a new turbo in Ebay, i did all the upper disassembly but when I lift the car and I try to start the lower dismantling my surprise was that the access to the turbo was impossible, I guess the 4x4 transmission is bigger that the Mazdaspeed3, so in a CX7 it's necessary to take out the engine to replace the turbo :(

@randomroadstraveled3710 3 года назад

Good job and good video. Thanks for the upload.

@haziqahh2206 Год назад

What intercooler you're using? Looks great !!

@DikkiSetiawan 8 лет назад

Hi Ally!... Love from Indonesia !

@Puneet_Sidhu 3 года назад

Amazing work!!!

@stevenspence2804 7 лет назад

when you took out the turbo. did u take it out from the intake side? or did u take it out through the exhaust side?

@mjl6425 5 лет назад

Where there any symptoms from the turbo seizing? Also was there noticeable shaft play?

@DevCom666 6 лет назад

This was a huge help. I just ordered a new turbo and DP b/c my stock K04 (for an '07) is smoking and burning a ton of oil. Would love to save $1500 and not pay my dealer to do it.

@brianburke396 6 лет назад

Great job ally, how on earth do you stay so clean??? Good video,,, who says ladies can't be mechanic's, very well done, more power to you.

@crue3139 3 года назад

OMG thank you so much for this video. About how long did this take? I'll be using this video for a guide to replace my turbo here in the next few weeks, hopefully I'll have some help. Pretty sure my turbo is going out. Its been smoking under hard pulls for a while now. And I just noticed a weird noise under hard acceleration that sounds something like turbo whistle and really weird rattling sound. I'm going to do some inspecting before I jump right into replacing the turbo to make sure its the turbo and not something else like the timing chain or AC compressor, but I'm almost positive its the turbo.

@hyoungseo1106 7 лет назад

잘보고 갑니다..차 다이 실력이 대단하십니다..

@bissine1 7 лет назад

Wow I really Love this girl !!

@kevinmorales8094 4 года назад

Is there a break in period when you put in a new oem ko4 turbo?? I can’t seem to find my answer anywhere, it’s a he said she said thing.

@Malkav 6 лет назад

Where did you buy your used oem turbo?

@RTM459 8 лет назад

nice work

@snarzai3860 7 лет назад

How long did it take all together 3-4hours including putting back together?

@NguyenFamandChavez 7 лет назад

is that socket 3/8 for the o2 sensor

@jonah9165 4 года назад

Can I clock my turbo for under-route piping kit like this ? Without taking out downpipe ?

@mkirefu 8 лет назад

Why is everything so dam clean?

@meeks726 7 лет назад

the car is basically brand new. has like 50k something miles as mentioned before

@holdshiftt2run308 5 лет назад

@@meeks726 but they usually don't look that clean.

@TSloanorthologisticslab 5 лет назад

Get a decent paint brush and brush down your motor when you change your oil and wipe it down afterwards. Neglecting to clean your motor can cause other problems with rust etc.

@modeljetjuggernaut4864 4 года назад

@@holdshiftt2run308 ikr.. The 'car repair guys' videos r a bit more realistic when it comes to filth and grunge with Mazda. I think that's the name of the channel.... You'll know when the speaker sounds like a cross between Jean Claude Van Damme and Kermit the Frog

@adrianslk1 3 года назад

@@TSloanorthologisticslab i doubt that cleaning your engine of oil will protect your engine from rust, i think its a contrary result, washing it a lot will get it rusted

@everest0411 8 лет назад

Another quick question....if you have car lifter to rise the car....will it be easier to do the work from the chassis compare to doing it from the top???

@Ready_Fire_Aim Год назад

im about to do this first time on my GT-T. practically the same im guessing except i dont have to remove rad/cooland or dump

@efrenolguin5469 7 лет назад

Where did you bought your used turbo?

@King-og4hp 7 лет назад

..thats why i love neon srt4 and cobalts ss tubros, soooo easy

@ledmk2 8 лет назад

Nice job

@kngkrmson2179 7 лет назад

Is there a difference between turbo brands? Does quality effect on speed for example?

@henryoakley7027 5 лет назад

How did you know your turbo was messed up? I don’t have a boost gauge but I’ve felt a loss in power recently and I think my turbo is messed up as well. It still kicks on but it sounds really weak and it sounds different all of a sudden. Any advice would help! I just don’t want to replace the turbo if I don’t have to, thanks!

@zombockerman Год назад

So helpful, thank you!

@zombockerman Год назад

I do wish you guys went a bit more into depth about how to remove the nuts. Most of mine were completely locked and many of them stripped! It took me three weekends to finish because of multiple road blocks. In the end, I wish I spent the 800 dollars for a professional

@samlee1802 9 месяцев назад

My girlfriend drives a 10 mazdaspeed3 and I drive a 07 mazdaspeed6. She pushed her speed crazy and I found this video very helpful in the future when she blow up her turbo.

@ericcirne3034 3 года назад

would this be the same way to change out a turbo seal??

@dreamrealitysyndrome 8 лет назад

is that a v-band clamp on tip?

@gavinderecola3849 2 года назад

How long did the whole process take you

@michaelwerger3722 Год назад

That was a great video

@minhn9853 6 лет назад

what about 07 cx7 w trans diff all wheel drive?

@mikeowens6291 6 лет назад

I just blew up the turbo in my Hyundai i30 Diesel, and halfway through getting the old one out, I thought I should go check a youtube video, as it seemed so hard, and difficult to get to. But after watching this video, mine is just a walk in the park! I think I should just get back to it and stop whingeing, and maybe look for a new girlfriend! Well done girl, a great video, and you've put me back on track!

@carlosaraujo7491 2 года назад

What size is you're t bolt clamps intake & inlet pipe

@emtae3 4 года назад

Was the turbo you bought rebuilt?

@craigzilla100 5 лет назад

Where did you find a lightly used turbo for $100 (if I heard that right)?? Thing looks brand new.. great videos!

@javibramasco2690 8 лет назад

what about the corksport turbo upgrade?

@anthonycrane16 5 лет назад

Same steps for a gen 1?

@huberv12 7 лет назад

Where do u get the turbo? Ebay or do you think that buy a remanufacturade its a good idea its a oem

@luccianoc7363 8 лет назад

You should make a video like this for every part on every vehicle ever.

@Thomas8892Q 7 лет назад

👍 great job. A husbands dream wife. Now I just need to teach my wife about cars- especially my Golf R. Cheers

@ricardocalderon9823 7 лет назад

Is oil passing through the oil drain when the car is off? I'd like to ignore draining the oil If I can.

@saucey_vn7346 6 лет назад

How long does it takes

@baggiestpanther2884 8 лет назад

sucks that you had to do it cause the turbo seized :/ but at the same time, (dunno about anyone else) but I found this video SUPER helpful, as I was thinking of upgrading the turbo on my speed in the future. At least now I know how :) so thanks for the video!

@jasonstavros Год назад

Thank you

@numinous4789 8 лет назад

Love my BNR S3. 385/380 @ the wheels when on the E28 tune, in good weather. And it's still very responsive. Actually, the lack of K04 "insta-spool" helps get the power down even better as well. S3 is just about perfect for stock block, IMHO. S4 or bigger if you're going to build, for sure.

@everythingdiy 8 лет назад

+Numinous Impressive numbers, looking forward to an S3. And yes the instant spool of the K04 can make driving a bit scary sometimes. One second your just having a good time then suddenly your torque steering towards a wall.

@smallputt 3 месяца назад

currently doing mine and i’m now at the 2nd o2 sensor waiting on my new turbo to be shipped

@truthlva3560 Год назад

I want to swap out the turbo engine altogether to a non turbo engine. Any mods I'd have to do?

@hilltop533 4 года назад

Thank You

@modeljetjuggernaut4864 4 года назад

christ u gotta pretty much dismantle the entire engine compartment to do this.. Another win for brilliant engineering.

@greddy1010 8 лет назад

my 2010 speed3 is 6 years old never had a problem with the turbo. thank god

@MichasQGP 8 лет назад

+greddy1010 well, k04 turbo problems on Speed3`s are not uncommon. However, there are a lot of them, pulling strong, without any problems. Sadly, mine died on my last year, even though the car was stock. Changed mine to an BNR S1, hope this one last a lifetime ;) Good luck with your Mazdaspeed. Cheers.

@luckywest1467 4 года назад

Don’t even have a ms3 yet and watched all of your vids lol

@carlosduprey1778 5 лет назад

I going to share this video on my Facebook

@flee78 6 лет назад

Kudos!

@culturegarvey4912 3 года назад

Wow I’m very proud of u

@amirgoldline 3 года назад

You are amazing unbelievable and most inspiring ....!!! My God 😮😭😭 I simply can not believe it. God bless you really . VOW 😮👍👍👍👏👏👏 I am glad i found this video and got to know such skilled and amazing lady who gives me courage to do things far simpler than this job. Thank you so very much 😄🙏🙏

@ajdeltoro2449 4 года назад

So after i finished installation i started it up and immediately began to hear intermittent squeaking with a rough vibration and shortly after some smoke began to rise from the engine. Any ideas why this is happening???

@gcphotographers-channel 8 лет назад

nice work. took you long enough to upload how videos again

@pauljmagson3645 7 лет назад

heheheh i love how hard it is or rather how long this takes just to get a Turbo off and put a new one on! was so simple :D

@cooldude2245 6 лет назад

That was a lot of work!

@philh9238 8 лет назад

what is your full time job? not a technician?

@Funrunner008 5 лет назад

What is that a cx9? If it's a 7 my airfilter doesn't look anything like that is that a CAI?

@jonkR96 7 лет назад

Did you remove the plastic shroud thing over the intercooler to improve air flow? Any noticeable increase to power or efficiency from doing that? Thought about doing that to my MS3.

@everythingdiy 7 лет назад

Don't, that plastic shroud is important for proper airflow and cooling of the intercooler. If you remove it, you will for sure see higher boost air temperatures and reduce the effectiveness of the cars cooling system. The shroud has two important features first it creates a funnel for air to flow through the cooling channels of the intercooler and second it regulates air pressure over the intercooler and around the engine bay. In order for air to flow through something there needs to be an area of high pressure on one side and low pressure on the other. If both sides are equal or close in pressure you will see little to no airflow. This is what happens when you remove that shroud, you allow more air to flow around the intercooler which will end up pressurizing the engine bay and stopping air flow for not only the intercooler but the radiator as well. It's been tested may times on this car and the results of removing the shroud always equated to worse cooling performance. We actually do have a shroud; but it’s different because we run an aftermarket intercooler.

@jonkR96 7 лет назад

everythingdiy oh, ok. I was curious about that being a possibility too. Thanks for the response!! Great Vids by the way! I'm a commercial electrician and work with my hands daily but working on cars has always worried me, excluding the "simple stuff", i.e, oil change, filters and such. But now I'm pretty confident I can do a lot more. So thanks for the Great videos! Subscribed!! I've only just started watching but do you work exclusively on the MS3? I have a 2012 "base" model. No Nav,HID or any extras. All Stock too, but I've recently put Hawk Pads and Centric Cyro-reated rotors. Nothing special, really.

@MatthewMaranan 8 лет назад

Holy crap they make O2 sensor sockets? That is awesome! haha

@everythingdiy 8 лет назад

+Matthew Maranan Yup. This one was made by Tekton and cost around $12.

@MatthewMaranan 8 лет назад

+everythingdiy Awesome! Tekton is pretty legit, I have a set of punches by them and they are awesome.

@KrustyKlown 8 лет назад

+everythingdiy (very nice job with your videos) ...a flare nut wrench can work also .. all these specialty sockets & wrenches can only apply limited torque, since they are split or relieved to allow the O2 wire to pass through ... PB Wrench may help, but my experience is, get the torch out, heat it up real good, then you stand a chance of getting it loose by dead blow hammering on one of these special wrenches. If you reuse the O2 sensor, expect to have to replace the metal gasket (they corrode from heat / humidity and can disintegrate when loosening the sensor).