How to Replace Rear Wheel Bearing on Discovery 3/4

Подписаться 24 тыс.

Просмотров 72 тыс.

0% 0

Sleeve Puller Kit: www.amazon.co.uk/gp/product/B...
How to remove the rear hub and replace the bearing on a Discovery 3 using simple tools.
- - - - - - - - - - - -
Due to factors beyond the control of FixItSam, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. FixItSam assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. FixItSam recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of FixItSam, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not / fixitsam .

Авто/Мото

Опубликовано:

22 апр 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@AndrewCleland1972 5 лет назад

Nice video - good to see it done with 'normal' tools and a bit of fabrication for those of us without air wrenches and 20 tonne presses. (Glad you replaced that backing plate as well!! ;) )

@chadbrandonstreet 2 года назад

Great video! Thank you for clear audio and good lighting/ video angles.

@v8trauma 4 года назад

Glad to see the bits are available these days. Did a d2 several years ago, cheaper to have the job done than buy the parts and diy. Bearings weren't available, just complete hubs. Priced the job up for a laugh, twenty quid cheaper to have it fitted by an independent.

@spuudercat 5 лет назад

I was looking for the parts to do it and came along this video. Really informative and clear on what to do. I'll be taking mine down to the garage now mind as I think in comparison to the fronts it seems a lot more work. Thank you for the upload

@dobsondwd 3 года назад

top tip put it the the freezer till you are ready to install it will pop back in easy

@turdbglr Год назад

Thank you for this!

@michaelminers2612 Год назад

Really clear, thank you

@morrellglassstudio6204 4 года назад

Clear and informative, many thanks.

@Comedyislandwilly 2 года назад

Class job helped me out

@davisscott8499 Год назад

This is a great video does anyone know will the half shaft pull out when the hub is removed?

@COM70 3 года назад

Could I be really cheeky and suggest you leave the camera on manual exposure or AElock once you have your exposure set, as under the car is a high contrast area, and putting your hands in and out of frame brightens and darkens your exposure and makes it difficult to see detail. Love the vids.👍

@CP-ok1gv 2 года назад

Great vid. What are the torque specs for this?

@medemo8953 Год назад

Thank you

@steveshih4622 5 лет назад

Thanks so much for the video. I’ve got a few questions I’d like to ask you. Were there any symptoms while your were driving? How many kilometers did you put on those old bearings before replacing them? Thanks again.

@FixitSam 5 лет назад

I caught it early before it started making noise. Just noticed a small bit of play in it when it was jacked up. Had put 70k on them, it has 220k so not sure if they are original or not.

@kapilamuni 4 года назад

Very clear and encouraging DIY. Can you tell me the source of the bearing and it's part no, please? Everywhere they sell the complete hub not the bearing. Thanks.

@dazz180 3 года назад

Check on line for advance factors based in Southampton quality parts

@cchevy100 4 года назад

Hi can you tell me how you got the parking brake cable pulled through the shield?

@deanc1320 Год назад

Great video. Like others can you please share the 1/2 plate dimensions?

@VDSG94 4 года назад

Anyone know the torque settings for the three bolts you have to take off to remove the hub?

@graemevass745 3 года назад

Does it matter what way round the new bearing goes in?

@adriancronin35555 Год назад

hi sorry quick question do i need to remove the bearing to.change the backing plate ? have an lr4 2013

@adriancronin35555 Год назад

hi, i need to replace the backing plate do i need to do the samd as you did its a lr4 .

@adriancronin35555 Год назад

hi, do i need to remove the hub to replace the break backing plate on the rear lr4 ?

@92m5 3 года назад

What's the messurements of your plate steel tool?

@CP-ok1gv 2 года назад

@<a href="#" class="seekto" data-time="560">9:20</a> anything special you have to do or just have to put it back on normal with tightening of bolts?

@Comedyislandwilly 2 года назад

Hey just wondering not sure if bearing is broke when I turn right around round about seems to feel Like it’s sliding mechanic said it could be hand brake catching could the bearing be problem thanks

@FixitSam 2 года назад

Is the traction control kicking in? Check all tyre pressures are equal as they can cause that.

@chrisdisalle2400 4 года назад

What were the dimensions of the steel plates you welded together. I know you said they were 1/2" thickness, but how long and wide did you space the three pieces?