Key won't turn ignition - ignition lock cylinder Chevy Silverado 1999-2006

Подписаться 79 тыс.

Просмотров 1,7 млн

50% 1

My ignition key will not turn. At least not right away. You have to wiggle it a certain way for it to work. It's time to change the ignition lock cylinder. It's easier than you may think. You 'll need to remove the cover from your steering column. From there it's a piece of cake.
Please subscribe to my channel and click the notification bell icon to receive notifications when I upload new videos to my channel. Thank you!
/ @thedaninator
For business inquiries, please contact The Daninator at:
the_daninator@hotmail.com
Instagram: @the_daninator_yt
Disclaimer:
Due to factors beyond the control of The Daninator, I cannot guarantee against improper use or unauthorized modifications of this information. The Daninator assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. The Daninator recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of The Daninator, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not The Daninator.

Авто/Мото

Опубликовано:

19 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 550

@sadiegirlwolf 5 лет назад

NOTE: if you do this procedure and you can’t get your new ignition to pop right in you have to take a big screwdriver put it in the hole and rotate the ignition square all the way back, after I did this my new ignition slid right and and worked great!! Thanks so much, Greg

@flyin2low2c 5 лет назад

Thanks for that info !!

@edwardeliyahhamner4340 2 года назад

Thanks because that's excatly what I was experiencing.

@jaybrown5985 Год назад

Someone try stealing my truck my key won’t turn at all

@SonnyThomasShow1 Год назад

I appreciate you also showing how to replace everything step by step as you put it all back together. Lots of times people just say "reverse procedure to finish it." You actually did it. 👍🏻

@YoBabyDaddy2023 4 года назад

Dude, thaaank you...got a cylinder for $60 bucks and did it...saved me hundreds of $$$

@johndefeo26 4 года назад

Daninator! This video saved my butt on a cross country trip. Did this as a last ditch effort to see if I could get my truck to start and it did the trick, safely back on the road an hour later! Hats off to you my friend!!

@TheDaninator 4 года назад

Glad the vid helped you out!

@lucasarielbarrera7313 4 года назад

You need to go until start position, but put in reverse and after that, turn the key until start position and push the retainer and pull it out. I'm a professional locksmith.

@shawnglover5768 2 года назад

THANK U!!!!!!!!!!! Im outside sweating my ass off trying to pull the cylinder out and it did not come out til I did what u said

@webrad98 2 года назад

Thank You! I was stuck in the driveway blocking other cars and after getting the covers off was able to press on the lock rod enough to park the truck to the side, I took the car and got the parts and now it works.

@gw4203 7 лет назад

Wow, thanks for posting this! You saved me another almost sleepless night and an expensive tow. Not to mention the mechanics charge.

@AgnesM 6 лет назад

G W you did it all yourself and it worked out?

@minnesota7010 2 года назад

Did mine for 12.99. Thanks. If you lived close id buy you few beers... Locksmith wanted 300.00

@rememberussliberty1822 4 года назад

I didnt want to give up my key and have to use a diffrent one for doors and ignition. Took out the lock cylinder like he did, got a very fine file. In my case it wasnt those two little pins causing my problem it was a sharp edge that had developed and it was catching. Rounded a few edges and bingo!! It is very easy to start these trucks without a key i discovered..

@brandenbeaverbone5564 2 года назад

I like your pepe pfp good sir I did not read your comment however, that is all.

@JeffL1234 4 года назад

Thanks, easy to follow instructions. Done in 30 minutes. We did have to use flathead screwdriver to line up inside parts to insert new ignition.

@johnorosz7477 3 года назад

@webrad98 2 года назад

Same Here. Glad I had a flashlight to see why things weren't lining up.

@nolancushing2811 2 года назад

Thanks so much for the video! It totally came in handy. I didn't want to pay an arm and a leg to fix it. Thanks

@rextorgerson8004 9 месяцев назад

Thanks for posting this video only difference was mine was a 2006 Z71 made my repair easy 👍👍 Just a couple different steps on mine. It didn’t have bolts holding column plastic together so all I had to do was use a small flat screw driver to start separation of plastics. Carefully Oh also I had to hold key all the way forward in start position to be able to push in release button to pull out old lock cylinder. Thanks again 👍

@CreekyGuy 6 лет назад

Totally pro! Excellent tutorial. Even the volume gain was good (often lacking elsewhere).

@iwinzeazy 8 лет назад

Be sure and try a factory key first. I had called the locksmith and told them I was gonna try key first. I had given my wife a key to my truck when I bought it 9 years ago and lucky for me she still had it and boom! It started right up!!!! Basics first :)

@tommurphy220 6 лет назад

Bless you, my new friend. I watched another video to diagnose and understand that this was something I could do. But I couldn't get the top housing off the steering column of our 2003 Chevy S10 until I saw you identify the problem bolt, AND suggest using a 4 mm socket wrench to get it off. (Watched 3 other videos before yours, and they suggested removing the steering wheel and airbag to get at it. No!) You saved me tons of time and money!

@TheDaninator 6 лет назад

Good deal! Thanks

@JBoysbarbershop 4 года назад

One thing I'd like to add that happened to me while I was replacing the switch was ,When I took the switch out and went to put the new one in. Inside the ignition itself, moved in there. so the new key switch wouldn't go back in until I put a flathead in there and turned it back the match the key cylinder ,Then it fell right in . Thanks for posting

@JBoysbarbershop 4 года назад

P.S. There was no 4m bolt in there. just used a finish nail to remove the switch.

@chilarue6279 4 года назад

You save my life!! You need a reward lol I couldn’t figure out why it wouldn’t fit!! Thank you so much

@tiffiny69 2 года назад

Bro!!! Thank you so much for this video. I'm having this exact problem, and no man in my life to help solve it. Lol I should be able to fix this no problem! You are a life saver!!! Bless you!!! 🙌

@spamwagon 2 года назад

So, my ignition switch would NOT move, NO way to rotate to the start position to remove/replace. I pried the plastic off the switch and located the keyway that pops up to lock the cylinder. The springs can fail and the keyway does not disengage from the housing. It's basically right where the arrow on the plastic is. I used a die grinder to cut off the shoulder of the cylinder right where that keyway is (careful not to damage anything else). Put the key all the way into the switch. Then, I took a baby (very small) flathead screwdriver and pushed the keyway down (back into the cylinder slot), tapping the screwdriver in as far as I could. Had to help turn the cylinder with some channel locks, but I got the cylinder to rotate clockwise to that start position and I could then pull it out. New one popped right in.

@lovetofly32 2 года назад

Just had mine all appart because mine was stuck in the crank position. That little gold plate under his tool on the tumbler at 3:57 was popped out. The corners of it are stamped into the casting of the aluminum tumbler. It looks like it holds the springs in the lock. I tapped the spots back down in the corners to stamp it back in place and now it works again. It's very soft aluminum. Mine does do the same thing this guys did and I also thought it was the pins catching on those ramps but I can hold them both IN and it still catches. I think its the little black block on the side of the tumbler that sticks out just a fuzz when the key is out but then goes in when the key is in. I believe it's what prevents you from turning the tumbler without the key in. I don't think it's coming out of the notch where it rides in the female part where it goes into the column. It seems a little cockeyed. I believe that's what catches and not the pins.

@salvadorbernal9392 Год назад

Finally a straight to the point video nice work you made it look easy thank you

@wrucker1000 5 лет назад

The video was great. I have a 1999 Silverado and my ignition lock cylinder needed replacing. I was nervous to tackle it at first, but with the video you created made it a breeze, once I purchase the right tools. The only thing that I would add is: When inserting the new cylinder, you may need to use a big flathead screwdriver to insert into the core space to turn the switch just a little to line it up to receive the new ignition. cylinder. I had to figure that out to get the cylinder to seat properly. When I put everything back together, it works like new! Thanks.... Oh yeah I had the dealer to set the cylinder to match my existing keys.

@anthonyg9389 2 года назад

How much did it cost for the dealer to set the cylinder to match the existing keys?

@chrisg1364 2 года назад

@@anthonyg9389 did u ever find out??

@anthonyg9389 2 года назад

@@chrisg1364 no, I just bought aftermarket ignition lock cylinder from amazon

@carlospaz209 Год назад

Thank you William, your comment saved my ass tonight. Small turn from 10 o'clock back to 12

@nuttinbetter2do451 Год назад

Thank you very much for posting this video my truck recently got broke into and they ruined my Ignition switch so I'm going to have to change it out. this video helps a lot thank you.

@Ray-hg3ie 7 лет назад

Thanks!!!!! I spent all afternoon trying to get the top plastic cover off. Never would have found that 4mm screw without your help. Probably would have had to rip that piece out before I found that damn screw.

@TheDaninator 7 лет назад

Haha. I'm sure that happens alot!

@brucejamison7809 Год назад

It is not actually a 4 mm screw. There are star sockets that are the correct tool for this.

@robertrutherford9438 3 года назад

THANK YOU FOR THIS VIDEO!!!!!!!! This is the easiest serious problem I've ever fixed. Life saver for real!

@Janzer_ Год назад

this is great. an option is to buy an "un-coded" ignition lock cylinder and code that (there's videos on how to do that) so you won't have to use two keys.

@deejay4839 5 лет назад

Thanks just replaced my ignition switch appreciate the video saved me $150.

@TheDaninator 5 лет назад

Awesome!

@anthonytorres5648 7 лет назад

Thanks for the video bro now my 02 escalade has a functioning ignition switch again

@TheDaninator 7 лет назад

Awesome!

@williamrush8370 Год назад

VERY GOOD INFO DIRECTION EXPLANATION AND PIC OF ALL POINTS NEED TO FIX THIS PROBLEM, THIS MAKES YOU MY FRIEND INDEED! THANK YOU THUMBS UP TO YOU. KEEP UP THE GOOD WORK!

@johnnybrents91 3 года назад

The ignition not turning has absolutely nothing to do with the spring pin as you referred to. It has to do with worn wafers in the lock that are not matching up with your key. All you would have to do is go to a locksmith and get him or her to replace the wafers and your lock is good as new. And you wouldn’t have two keys. You could’ve had the new lock rekeyed to match your old key so everything is on one key but then again you spent money on a new lock that was not necessary. That groove as you called it you said wore out does not happen. Always a good idea to ask a pro. You save money and you don’t misinform people with this nonsense.

@goldenstatepicker Год назад

Johnny is Mr. Know-it-all. Those guys are the ones you want to avoid taking your car too. @@jaysmokey

@CSpad 10 месяцев назад

Well Johnny know nothing. A locksmith is gonna cost you between $100- $180 to make you a transponder/chip key. While for $100, I got a new lock cylinder& 2 new transponder keys that I was able to program myself.

@Gumby409 8 месяцев назад

You’re the bastards people need to stay away from . Why the Fuck ramble on about this . Stay dumb

@yaboi5686 3 дня назад

@@CSpadunless you got a remote I’m sure you’re not worried about your ignition key not matching with the door anymore, better hope that battery doesn’t run out

@5150santana 6 лет назад

this video saved me alot of money by doing it myself thanks

@martytruelove5026 4 года назад

THANKS Buddy,nice to know the tools required going into something

@1320Jason 2 года назад

Agreed

@trueopsimath 8 лет назад

Good video. I've got the same problem, and now I'm confident I can fix this myself. I'll give it a try this week.

@TheDaninator 7 лет назад

Happy repairs!

@trueopsimath 7 лет назад

I decided to tear into it this week. Apparently the previous owner had struggled with the problem. To begin with, getting the covers off the steering column was a snap because he didn't bother to put the retaining screws back in. With only a moment's struggle, I was able to extract the old cylinder, to discover that it had been liberally slathered with grease. That would explain why everything worked fine when I bought the truck, but started going downhill soon after. I popped in the new cylinder without any issues and replaced the covers. The whole process took only a few minutes. Thanks again for posting your video!

@stefansmyle9369 10 месяцев назад

This video was very helpful for me because I learned how to pull the cylinder out mine was broke on the on position if your key won’t turn you need to push both pins in by sliding something that will lift them out and then it will turn to the start position I need to crank it all the way over to push in the pin you will see that if you buy a new lock like I did this video is very helpful thank you A+

@mattcox3373 4 года назад

Thanks for this video. You saved me a lot of money and stress. My key wouldn’t turn, but a flathead and hammer freed it up pretty easily.

@mattcox3373 2 года назад

@The Masked Hoodie luckily no. I was just careful

@mattcox3373 2 года назад

@The Masked Hoodie my ignition switch wouldn’t even turn for me to be able to get it out to change it. So I had to stick the flathead in where the key goes and hit it with a hammer until it broke lose. I was changing the switch out anyway so I didn’t care if I messed that one up

@DrSexiiful 2 года назад

@The Masked Hoodie you could stick a flat into the ignition while using vice grips to turn the ignition itself have to remove the plastic ears first though make sure u clamp onto metal

@eugeneirby228 5 лет назад

ALL I CAN SAY IS THANKS THAMKS THANKS MADE IT SO EASY, DAM GOOD VIDEO!!!!!

@edpotts9168 5 лет назад

very well done, straight and to the point..kudos !!

@pedjastanich4347 6 лет назад

Thank you for sharing. You are a gentleman and a scholar.

@TheDaninator 6 лет назад

Why, thank you kind sir.

@ireuel357 4 года назад

Key won't turn...except that yours does, so it's easy to switch out the cylinder. Not helpful.

@boggy6060 Год назад

@romangarza6037 Год назад

79 dodge brougham rv installed new ignition

@geraldturner8377 Год назад

Same issue

@davidhoneycutt1965 11 месяцев назад

Take the key out and smack it with a screw driver handle and keep working it. She'll give

@jasonboyko 11 месяцев назад

@@davidhoneycutt1965smack her around a bit, and she'll comply, lol

@eshacooper8741 2 года назад

Thanks for the thorough explanation. Top cover was giving me a time.

@gagewade2946 3 года назад

Someone broke into my truck and snapped that part off so thanx for the video now i can replace it myself thanx man

@urbanbluecollar7813 3 года назад

Me too

@gagewade2946 3 года назад

@@urbanbluecollar7813 sorry to hear that i got a new part put it in and got theft insurance👌

@thycarguru4252 3 года назад

@@gagewade2946 did it work

@gagewade2946 3 года назад

@@thycarguru4252 like a glove i appreciate this guys video

@captprice1b-06 Месяц назад

Thank you sooooo sooooooo much, this helped me and my grandpa ALOOOOOTTTT 5 Stars! ⭐️⭐️⭐️⭐️⭐️

@surftoryblue 8 лет назад

Thank u! I just fix a my Girlfriends 96 Chevy 1500 Silverado Ignition Cylinder , it took me a minute jiggling it back and forth but slid out, thanks for the pointer !

@TheDaninator 8 лет назад

Awesome! Glad my video helped.

@brainyak7408 Год назад

For $28 + around $12 shipping, you can get one with a GM stamped key from Classic Industries. That GM stamp is important to some folks.

@discmotoslots 4 года назад

perfect! just what I needed for my sticky key! thanks

@lilgrover69 3 года назад

That's the AC delco that costs 258 bucks right?

@bobthomas143 3 года назад

How do you get the cylinder out if the key won't turn to the on position???

@bobthomas143 2 года назад

Got it out by getting a thin metal strip and pushing the tab in. After that 15 minutes , new one installed and job complete.

@minnesota7010 2 года назад

@@bobthomas143 Thanks Bob did mine today I got a thin piece of metal like you said and it work thankkkkkkk youuuuuuuu! I want a by you a case of beer if you drink... Peace out....

@Beliefacy Год назад

@@bobthomas143 please can you be more descriptive? Thin metal for what piece? Wtf

@brucekolkebeck8054 8 лет назад

Worked like a charm! Thanks

@ramirez23456 8 лет назад

gracias amigo me ayudo mucho tu video llevo 2 anos con ese problema porfin pude arreglarlo thanks

@tupito45 7 лет назад

thank you it worked good for me and I didn't have the old key so I just used my new key to turn it as I put pressure with bar and boom...thank again

@drolnady 6 лет назад

Replacing the rubber shift lever 'boot' while in there is also a good idea. And, if you have tow/haul switch, the orange wire is prone to breaking because factory stretched too tight.

@ultraman50 2 года назад

Great video. Thanks. I R/R one on my 1995 f150 long ago and it was so much easier. Didn’t have to take anything apart. But still looks easy enough. Thx agsin !

@irwinjoseph4825 5 лет назад

Great video, I changed mine yesterday .

@encoencomen8361 2 года назад

Great video. Some amateur Jackass broke into my truck this morning and boogered up my ignition switch. Didn't get the truck. If only I was up I could of put 6 slugs through his partner's windshield.

@cemetery76 5 лет назад

don't know if mine froze up from moisture got in it,or it's jacked up. I sprayed PB Blaster in the key hole got it to turn,it's not gonna hurt it. you can use WD40 to it should work, hope this helps.

@midos6767 4 года назад

My 1995 Chevy S10 has the same problem with the ignition switch not turning sometimes. I just jiggle it a little and it works. But I like to keep it that way so that my girlfriend can't drive it. I don't want anyone else driving my old truck but me.

@24chikillin 7 лет назад

Wow that was fast thanks for the help

@jamarlewis3050 7 лет назад

Hey man just wanted to say thank you for your guidance ...

@TheDaninator 7 лет назад

Glad it helped you out

@TKWkw 3 года назад

We cant turn the key to the on position even after pulling cover off!! Whats next?

@whistlinframer6812 3 года назад

Where are you man? This helped me so much that I want to buy you a case of beer

@johnorosz7477 3 года назад

1996 Chev. C-1500: This works great but the fact is you need the ignition to go forward in order to even remove the core/barrel. I cannot turn the key at all. So it refuses to let me remove the barrel cylinder and replace it. Both keys refuse to work on this ignition. May need to call a specialist.

@wallace2157 2 года назад

im in same situation key broke off and 2nd set was a gmc set from csnada?

@wallace2157 2 года назад

just got it towed bit took column apart can get out of park still wont turn ignition though

@klolwtf5602 6 месяцев назад

There aren't any torx screws under my steering wheel. 2003 2500hd.

@andrewstartek5846 2 года назад

Looks like you were able to turn the key lot of help

@scottherrin5812 3 года назад

Many thanks. This made it too easy!

@stephanlapointe6771 6 лет назад

Thanks for the video! When I put my new cylinder in it fit but it won't turn all the way back to off. Does this mean something else is wrong?

@studyfamily145 4 года назад

My car was broken into and the column was destroyed can find the parts how do you modify an ignition switch in 2001 crown Victoria ltd five point oh or can i wire a toggle switch to start it

@1320Jason 2 года назад

I gotta do this to dad’s truck. Thanks for the video!!!!

@johnsmith9150 2 года назад

I'm having a great problem taking egnition switch out.ive pressed the pin in the hole to release cylinder but still won't come out

@truthaboveagenda 8 лет назад

. Well stated, well done video. -Joseph

@meatyman925 7 лет назад

Thanks for the video worked for me I have 2002 chevy Silverado

@davidcollins6956 7 лет назад

Jonath an

@Lore-wv5mt 6 лет назад

Jonathan did u haded to program it???

@bghankhernandez 6 лет назад

Perfect instructions. But when I pulled ignition out,inside tumbler turned so new ignition wouldnt go in...aaahh thought for sec then i used a 5/16 closed end..to turn a little to line up,went right in. Thanks.

@johnorosz7477 3 года назад

Special Note: if you do this procedure and you can’t get your new ignition to pop right in you have to take a big screwdriver put it in the hole and rotate the ignition square all the way back, after I did this my new ignition slid right and and worked great!! Thanks so much, Greg

@rodop5656 5 лет назад

Good stuff. Appreciate it

@DirtRoadDude 5 лет назад

great help! thank you! just did mine and found out have to turn the key to the "start" position to remove the cylinder. so unhooking the battery is the way to go.

@angelrosario6052 2 года назад

What if you can’t move the key to start

@GPski 4 года назад

Hi any idea what the little white switch block is just on top of the key block with the long white plastic "finger" on it ?

@joserodriguez3418 8 лет назад

Thank you that will help me on my truck it when out today

@Tristatehooligan 7 лет назад

Mine got stuck while it was on, after about 1/4 of gas wasted. I disconnected the battery and alternator. The. Key cylinder was also stuck. Do you have to reprogram a new key or is just plug and play with the new one

@abrahamaragon3365 2 года назад

Thank you very much for the information

@seeyeshua 7 лет назад

thanks buddy. ..u made it look easy & it was thx again

@TheDaninator 7 лет назад

Awesome!

@z4u68 4 года назад

Good job, Hey do you think if I put an electronic ignition switch on my 98 astro Can I do it without taking the steering wheel off? Thanks in advance.

@oesco96 6 лет назад

On the ignition cylinder housing, what do those 3 wires do? (yellow, orange,red wire?) My 2000 chevy does not have that piece and the wires sre just there.

@Val_Halla777 5 лет назад

Nice job. Thanks for this..exactly what I was looking for. I think I have related issue..in my situation it takes several random turns before the key actually engages the starter/ignition..do you think this is also some type of wear on the cylinder ? Thanks again - great vid👍

@TheDaninator 5 лет назад

Val Halla it’s possible. But I would guess that may have something to do with your ignition switch...but that’s just a guess.

@Val_Halla777 5 лет назад

The Daninator ok..Thanks for the reply. Really appreciated. Cheers

@mikemckenzie1796 3 года назад

Saved me a pretty penny thanks!!!

@bigbeniv 5 лет назад

you're a lifesaver Bro!

@dneuman7455 5 лет назад

what if you cant turn the key to the on position ?

@stunner_wolf2231 4 года назад

That's what I'm askin.

@bigmike3455 4 года назад

Thats my problem 😂

@ConnieFoster1 2 года назад

Well, great video. I was able to get thru all the steps until the part where the key has to be turned on in order to release the lock cylinder. But that's my problem! The key won't turn. Very frustrating

@angelrosario6052 2 года назад

Did you ever figure it out?

@chadrudeseal5503 3 года назад

Excellent video. Thanks

@adrawagodfrey6313 5 лет назад

Good lesson learned 😀

@lowpricekeys6629 3 года назад

Thank you for sharing this detailed amazing video great job 👍⭐⭐⭐⭐⭐

@renekravmaga8564 3 года назад

Thanks so much, It help me a lot

@jonathanbertke8396 7 лет назад

I have a 2000 chevy silverado... I can turn the key and start it but the key doesn't turn back so the starter just keeps running so I have to manually turn it back. Do u think I need a new cylinder?

@KaneadshaJones 8 лет назад

#homemaker, great video i am not mechanically inclined at all and i was able to so this

@poolnoodle5311 2 года назад

Awesome video. My 1999 also have the GM Jiggle. You didn't have to program your new ignition to the pickup?

@taknmybeatings7036 3 года назад

Well sir that key did in fact turn. So how DO you do it when the key WON'T turn?

@jamescox9650 3 года назад

Yeah because my lock cylinder won't move at all.

@bassaddicts5744 4 года назад

Will this work if you don’t have the factory key. I lost mine and the locks have previously been changed. Thinking about doing this instead of having it towed to the dealer ship for someone to make me a new one

@johnhelkenn3025 4 года назад

So they key turns... not what it means when your title say "key won't turn"... thanks for the "help".

@joaquincarranza7569 Год назад

Thanks alot it was so helpful thanks you very much appreciate

@kevinschmidt2301 7 лет назад

I did what another video showed drilled a small hole in the cover and came out fine ,but it was not the problem it is the ignition switch,on to find those videos now.

@user-wj6pu6wo2q 8 месяцев назад

Excellent video about 30 minutes and I was up and running

@texantracey Год назад

Excellent video!

@thedetailcompany3091 6 лет назад

But what if you can't turn the key????..

@ericmartinez6692 3 года назад

Inhave 97 k1500. Turning on key wont start at all. Fuse 40 A / ignition keeps blowing out.I am getting a/c and light power all around interior. Battery seems to be fine.Can you guide me to my issue please from your experience on issue like mine. Thanks in advance.