"All things Kubota" including but not limited to - mods, tips, tricks, maintenance, implements, attachments , fabrication, customization & even operation. Almost everything I learned while attending Hogwarts Academy.
NOTE: Don't take me too seriously - I don't. I'm not here trying to make Google money. I don't think I'm some sort of an expert. I don't think I'm better than anyone else by posting videos here. I just want to provide an open mind with a different view - My only claim to fame is that I like cold beer, good whiskey and Cuban cigars. I've got a great wife who puts up with my non-sense & usually posts my bail without complaint. She's my heart & soul. I promise the good Lord above that when she goes, I'm right behind her! I am NOTHING without her and we both know it. So sit back, relax and enjoy - Feel free to contact me and I will answer all your questions unless you ask something rude or stupid that would normally get you a black eye if we're drinking in the same room!
I like Koeler engines. Much better than B&S engines. I too use non-ethanol gasoline in all my 2 and 4 stroke engines. Also as you did, I shut the gasoline shut-off valve off and allow the engine to use all the gasoline in the lines which ensures there's no gas in the lines and the carb is emptied. Hope you're finally getting some comfortably warmer weather. It's finally been getting in the 60's here. I'm down in NC but it does get quite cold. It's been in the 40's and 30's but the 60's is where it needs to be (smile). Enjoyed a full-watch. Thanks for the video. Stay safe and will see you on the next one. 👍🏽🙂
Hey there Houndsman! Good to hear from you again!....I too have been spending quite a bit of time lately in North Carolina. Looks like we're going to move down there in the next year. Yeah, something funny about that Kohler. Emptying the lines seems to be the key with this one. I'm disappointed that there's no priming bulb. Thanks for watching, commenting and supporting!!
Thanks for the video. Just picked up my new L2501 with install 3rd function valve. Just couldn't see $1800 for the Land Pride 54" grapple. The MTL grapple looks like the ticket! Just need MTL to display, " Proudly made in GA for Me in WI". Fly Navy!!
Great Joe....you're going to love that 2501 with grapple....lots of power and weight! Navy?? (LOL!) My son is an Airman down at Hurlburt field in FLA. They're ALL AMERICAN HERO'S. Enjoy the new - thanks for watching and commenting! Please don't forget to like, share and subscribe! Talk soon!
Problem with those knobs on sub compacts, (Regardless of make and model) is that they have internal leaks in hydraulic fluid, meaning if you install your wheel spinner at 5 oclock when wheels are straight, after a while you may notice it is now at 11 oclock when wheels are straight, they are better on electric power steering rather than hydraulic.
True..... True......I find I use it most while driving "turned around looking back." and while using the tractor "half-handed" with a beer in one hand the a cigar sticking outta my face. 😝 Thanks for watching - I really appreciate your comment and support!
I sent comments 8 months ago. On May 16, 2020, I ordered both the “Pat’s” and Mark’s stabilizers. The “Pat’s” showed up immediately whereas, as you warned, The stabilizers arrived this past Monday 02/22/21. They were worth the wait. You may have mentioned this in your video. One of the things I did not realize or taken into consideration is the fact that “Pat’s” devices extend your lift bars some 4”. I had a Ford 1220 previously (small sub compact, 13 hp @ PTO) I had to cut down a couple driveshafts for the brush hog and 4’ rototiller. These drive shafts were then too short when I went to the L3301 Kubota. I ended up selling both those implements. The extra 4” turned out to be a good excuse to move up to larger implements. Also, the stabilizers cost $250, not a game changer.
I appreciate your comment and thank you for your support!! I'm glad that you liked them as much as I do. I couldn't imaging doing it the old way anymore - how quickly we get spoiled! Enjoy the new toys!....um, I mean implements! Thanks again. Please don't forget to like, share and subscribe!
Purely my choice. I always try to get stainless if I know there's a high probability of having to wrench on them again. And, unless it's a big project with a lot of hardware - stainless doesn't ass that much to the bill. Thanks for your comment and for watching my video! Stay well my brother!
Is it a Coke or a soft drink? Is it a refrigerator or a Frigidaire? Is it a Victrola, or a record player? You really need to get some ramps for that trailer brother.
True..... True...... I just picked up a bunch of angle iron today just for that very reason! Thanks for watching - I really appreciate your comment and support!
Not a bad idea! But, anyone with a brain and the ability to reason could have done that. LOL! 😝 Knuckleheads like me have to do everything the hard way! Ha ha ha. I truly never thought of the car ramps. Thanks for your comment and for watching my video! Stay well!! Please like, share and subscribe!
Great company. Great attachment - no complaints here. Funny thing is that my neighbor uses it more than I do and it still looks and functions like new. Thanks for watching and commenting! Please don't forget to like, share and subscribe! Talk again soon!
I honestly don't know. I would check your manual to see what the flow rate is 1st - that will determine what valve you get. Otherwise, the plumbing will be the same unless you have a rear sub-frame and backhoe. Hope that helps, I really appreciate your comment and support!! Please don't forget to like, share and subscribe!
My nephew has the l2501 he said the same thing you need to push the clutch in to start it just curious as to why? I have the l3301 and there is no need for that
Kubota safety crap. There's a solenoid that cuts the power to the starter unless the pedal is depressed. It make no sense on the HST model and is easy enough to bypass. But I'm sure somebody got hurt on a gear drive unit doing something stupid and went after Kubota. Thanks-a-million! I really appreciate your comment and support!
I didn't want to have to keep tightening them up in the event vibration loosened them. Just one of those things I didn't see coming. 😝 Now, I loosen and tighten them every 150 hours or so. I appreciate your comment and thank you for your support!! Please don't forget to like, share and subscribe!
I got 90s for my valve. The hoses going straight up was a recipe for disaster and looks ridiculous. The other issue with that kit is the crappy joystick. Fortunately, the Mahindra joystick had a plug in it that can be easily removed and a little time with a 3d printer had a nice adapter and I've got the perfect setup.
Sounds like your came out pretty nice. Any pics or video? Thanks for your comment and for watching my video! Stay well!! Please like, share and subscribe!
Glad it was helpful Gary. They're a great company and make a great attachment - no complaints here. I would definitely recommend this setup to anyone without hesitation. Many on this comment threat report having the same experience. Thanks for your comment and for watching my video! You're continued support means a lot to me!
Glad you enjoyed it....thanks for stopping by and checking it out. I really do swear by this stuff.Thanks-a-million for your comment and taking the time out to watch my video! Stay well!! Please like, share and subscribe!
bought Kubota L2501 2nd day started hiccups like misfire, Dealer kept for 12 days, put more than 4 hours, Got worse, make more damage to the tractor, Now I have nothing but REMORSE. I should have bought KIOTI ..!!
Yikes. What are they going to do about that? I've never had a single problem with mine outside of some hydraulic fittings that used to weep now and then. I'll keep my eye out for your answer. That shouldn't be and the dealer should be miking that right. I appreciate your comment! Please keep 'em coming!! also, Please like, share and subscribe!
It's not for everybody. I don't know what else I could do without sanding, welding and painting.....Thanks for watching and commenting! Please don't forget to like, share and subscribe! Talk again soon!
great video man. thank you. Would you happen to have any part numbers for those shims? The parts guys at my local dealer will not sell them to me and I think I’ll have to order online. Thank you- Steve Collins Groveland Ma
Hey buddy I appreciate the shout out! I have been thinking about getting the hero 8 black as a second camera either that or a second hero 7 black. The 8 has some features I really like tho but it’s a bit more money as of right now. I love your camera setup with the external battery holder it looks like a professial rig for sure! You should see the junk I’m working with 😂 lol. My tri-pod is all bent to hell, camera is all beat up too but I have an external power brick like you have that I got from Walmart and it’s really helped a lot with making my videos longer. One question I do have tho is what amperage are your USB outputs in your external charger? I got the high output when I charged mine I wanna say it’s 3amp and the issue I have is when it’s a warmer day and my hero 7 is connected to it the camera will easily overheat as I think the charger is just charging it way too fast while it’s recording in 4k.. if I recorded in 1440p this prolly wouldn’t be an issue tho but I like to do all my videos in 4k and have had a real tough time finding a camera that can do 4k consistently with out overheating by getting over worked.. the hero 8 I hear is a lot better tho.. be curious to hear what you say.
Ha, ha, ha, ha.......there isn't a tractor content maker out there who hasn't run over a couple of tripods 😝 from time-to-time....wait until after Xmas - the price will drop on the Hero 8 Black now that the 9 is out. Also, you are completely correct. The power banks use 2.1amp outputs and I only use OEM batteries in the camera's. (They get pretty warm but no shut-down's yet). I cheaped out and got the low output bricks and that probably worked to my advantage. I only record in 4K and when I turn on the camera, I don't turn it off until I'm done so it's not unusual (for me anyway) to have 90 minutes of footage for 15 minutes of video. The whole reason I sprung for the 8's was because my gear was dying and when I looked online - everyone was raving about how much better they were over the previous models. Hope this helps. As always, thanks A LOT for the comment and the support!
Hey buddy I hope all is well! I thought about you the other day not hearing from you in awhile and decided to check back at your channel since I haven't gotten any new alerts (wanted to make sure I wasn't missing anything) I Hope your staying safe!
Great video buddy! And here I thought you were slacking! I didn’t realize you had a few new videos out since I came over last.. def gotta hit that bell notification haha. You did a great job getting those trees out of the creek. If you had more ballast you easily woulda gotten that tree out. I would def consider getting a heavy hitch weight bracket with some suitcase weights or maybe just grab ahold of an implement next time. I’m sure you didn’t think about it as you were going out there tho cuz who woulda haha. Nice job as always!
Thanks Biff! I hear ya on the bell. I haven't been getting notified from several creators......I think YT is trying to funnel everyone towards posting to increase engagement. I honestly forget about using the post feature. I HAVE to get a heavy hitch and suitcase weights for both of my machines. Have a happy and safe Holiday bro. Thanks for the support - talk soon!
Yes - agreed! This helps make things a little easier. Thanks for watching and commenting! Please don't forget to like, share and subscribe! Talk again soon!
Super glad it was helpful! With the battery issue aside, you can concentrate on your content and not have to worry about your gear. I appreciate your comment and thank you for your support!! Please don't forget to like, share and subscribe!
I had to watch the out takes multiple times. That was rich! I am going to have to start saving mine. I nailed my shins good on my trailer hitch one time and it was unbelievable what came out of my mouth while the camera was rolling. That wasn't the only thing rolling. My wife was getting a good laugh at my expense.
Same thing Gary.....no one gets out alive around here. Everything is fair game around my place. The out takes are fun to produce by frustrating when the camera's are rolling. I think that's the appeal - you capture that frustration. Thanks for the comment Gary - have a Merry Christmas!
Very nice set up and a very easy way to do it. Thanks for the step by step and thanks for the shout out. I love you tube for these helpful hints and tips.
Thanks! Hopefully - this video will help alleviate some of the frustrations others GoPro users are experiencing. Especially during the time lapse mode. Thanks-a-million for your comment Gary! I really appreciate your comment and support!
Bota, a great video. I noticed you said you can get up to 3 hours recording time on your Go-Pro 8 with the handheld pod. So will your Go Pro record that long without timing out or getting too hot? My old Samsung DSLR camera will only allow 19 minutes of recording then it stops all by itself then I must restart recording from scratch. Thanks for this video. Full-watch. Had to chuckle at the bloopers. I surely have a truckload of them (smile). Have a fine Christmas.
Yessir! My GoPro 8 easily runs that long at my current settings without overheating or shutting down. I guess that was a problem with older models but like I said in the video, I'm running two of them from start to finish without any issues or having to change batteries. Help me stay focused on my content and not get distracted with messing around with my camera. Thanks for your comment and for watching my video! You're continued support means a lot to me!
I would comfortably say that the small increase I did increased lifting capacity a few hundred pounds easily at a guess. I appreciate your comment and thank you for your support!! Please don't forget to like, share and subscribe!
Sure: 0.1 Shim 31351-37970 0.2 Shim 31351-37960 0.4 Shim 31351-37950 The gauge and connection can be found here: www.boltonhooks.com/product/hydraulic-pressure-test-gauge/ Thanks for your comment and for watching my video! You're continued support means a lot to me!
Great video I just installed 3 Rd function value on my mx4800. Have grappler coming in tomorrow. Was thinking of adding hydraulic top link in the back. I don't have any rear remote. Here's my idea to utilize the 3rd function value. Change hose ends that goes to the front with quick connectors. build a quick connect bracket in the rear. Have top link cylinder plumbed to bracket, with quick connectors. So I can simply disconnect hoses from front to rear and use function value as you demonstrated. Your thoughts much appreciated. Thanks Darryl
Absolutely YES! That works too and saves on some $$. Hydraulics can be intimidating and confusing to some. They were to me when I first thought about installing rear remotes and a 3rd function kit. I watched A LOT of RU-vid videos to try and get a handle on how hydraulics are plumbed. Once I figured it all out - I realized that there are several ways to make a similar installation. Thanks for watching and commenting! Please don't forget to like, share and subscribe! Talk again soon!
I DO HAVE a hydro drive and I honestly can't say that I NOTICED a speed difference. You would think that by increasing pressure - you would be increasing speed. The only difference I noticed was the lifting capacity in the loader AND in the rear lift arms. Thanks-a-million! I really appreciate your comment and support!
Thanks. After taping, editing and producing - they're just funny. My wife likes them! But she doesn't get out in front of the camera like your wife does! Thanks again for the comment Gary!
I have a MS390 that I have had for nearly 10 years. It does all my blocking and my heavy cutting. It will wear you out just carrying it around. I use my MS180 and my MS 250 for the lighter stuff.Great video Both Trac, as always.
Thanks for sharing Gary. I bought that a couple of years ago and I remember the day I got it.....I cut up everything I could find. The balance and power of a Stihl you can FEEL in your hands. My neighbor is a canuck - he runs Jonesred exclusively and shakes his head at my German log slicer! Thanks for the comment and the support!
Good thing you got it out before the creek filled with water. I had 28"dia, one fall in my creek that has water running year round. It goes from 6" to 3' depending on the time of the year. It was not fun removing it. Later
Yessir! I would have been a bit screwed if I waited until spring. the running water moves a lot of debris that can cause a dam. I can't imagine trying to pull one in 3 feet of running water. Did you get it all out?? Thanks for watching, commenting and supporting!!
@@BotaTrac Yes I got it out. It was a lot of work. When it fell the water was only 8inch deep. I have videos of it on my channel. Merry Christmas and Happy New Year! Later
Just note Teflon tape and paste is not a sealant it is a tread Lubricant, and you do not use it on flare fittings. Its for use on tapered pipe threads and Lubricants the threads allowing the male / female metal fittings to fully tighten with out galling. Possibly the Teflon paste you used actually Lubricanted the nut threads on the flare fitting which may have been already over tighten and galled, this could have allow a higher flare compression force thus stopping the leakage. Just my opinion 36 year instrument mechanic.
I'm sure that you're 10,000% right. I'm not a mechanic. I am a plumbers son. We do use Teflon paste on black iron pipe carrying natural gas so I had it on hand. The situation I have is that I have 2 Kubota tractors. for the longest time - I would develop leaks at the flare fittings. I thought that because they were already tighter than I was comfortable with, maybe they were just Chinese quality crap (???). Of all the thread paste I had on hand - the teflon paste was successful in stopping the leaks without over tightening them. I do use it sparingly and you have offered the best explanation so far, (.....And I have received my fair share of criticism for using teflon on those flare fittings) the paste lubricates the threads and prevents distortion to the thread surfaces due to excessive heat or friction during the tightening process. Thanks for your comment and for watching my video! You're continued support means a lot to me!
Ha ha ha ha ha ha! I gotchu! All things aside, except for this silliness - I really like the tractor. I have this which comes with a loader and backhoe and a L2501 (larger) with just a loader. What implements are on yours?? Thanks for watching!! I really appreciate your comment and support!! Please don't forget to like, share and subscribe!
Very informative! Much appreciated. Couple questions: How do you find the correct wire from the ignition that gets hot (12v +) when turned on? And when you find it, do you just strip it back a bit and solder your wire that goes to the switch onto that one? (And then of course tape it up and protect it.) Thanks again!
Hi Matt and thanks for watching and your comment! I don't know what your working on or what you're looking to do. You have to be very careful when cutting into the wire harness....you may void your warranty, or worse. My neighbor was replacing his car stereo and speakers on his Audi and he (accidentally) cut into a fiber optic wire - $960.00 to get his car fixed. I saw the fiber optic cable. it was brown and orange just like the speaker wire was supposed to be. I probably would have made the same mistake if I didn't know. That said, if you're sure about what your doing, I would start with a 12V electrical tester with a fine point on the end and try to find a wire that isn't "hot" when the ignition is off and is "hot" when the key is in the "on" position. I would also take the time to look over your fuse block for an "accessory" circuit with a 5-10amp fuse. Hope this helps. Good luck and if your not sure - try to find some help at the dealer or accessory store.
Matt, I have the same two questions. I guess one answered and also suggested finding an accessory fuse to use. Was this in place of spicing into ignition? Also second question -how do you make the connection into hot wire? I guess 3 way wire it.
@@BotaTrac Matt, I have the same two questions. I guess one answered and also suggested finding an accessory fuse to use. Was this in place of spicing into ignition? Also second question -how do you make the connection into hot wire? I guess 3 way wire it.
Yes! you're right! all we can do is adapt and overcome! Thanks for your comment and for watching my video! Stay well!! Please like, share and subscribe!
Thanks-a-million....that really means a lot to me. I really appreciate your comment and support! Hopefully, good Lord willing - I'll keep putting out great content!
Great video man! Love the way you loaded and unloaded your tractor, sometimes you gotta do what you gotta do, I didn’t see that as being unsafe so long as your in flat level ground like you said. Also nice job bush hogging, I always enjoyed bush hogging it’s a lot of fun, anytime you can get out in the sun and do a little work is a good day! Keep up the great work. Love the intro!
Yessir! Level ground is the key! I saw my neighbor do it and decided to scrap the ramp idea. When I said "Anything can go wrong, and usually will" I was referring to getting the shot in one take without something stupid happening - making me look like a fool!! Also, I agree with your bush hogging statement - pop the earbuds in and spend a few hours in the bubble......it's good for the soul. 😎 Thanks again for watching, commenting and supporting!!
@@BotaTrac Absolutely man! And oh yah I knew exactly what you were talking about cuz the minute the camera is on you that's when things go right to hell! lol. When I don't record myself welding i do fantastic welds and when I got the camera recording my welds look half as good, goes with anything I do! lmao. Great video keep up the great content!
I used one of my loader tractors to lift the back end of my GR2120 this summer when I ran the belt off. Took a couple tries to get the right height. I will try this next time. I bet that will work very well. Never thought of that. I learn something from every one of your videos.
WOW! Thanks! That means a lot to me. I'm too beat up to crawl around on the ground - seems I'm always expanding my collection of metallic body joints (shoulders, knees, a hip). I can remember my father saying "work smarter, not harder." now I know why. Thanks for your comment and for watching my video! You're continued support means a lot to me!
Hey Both Trac, how did that feel the 1st time that you backed of that trailer? Those are the kind of moments that give you pucker power. Bummer about the plow. Love the out takes. That never happens to me,Lol. Your video quality is amazing. You have a great camera. I use a Go Pro Hero 7 Black and Barb's I phone for my channel. Advantages and disadvantages to each, but it's nice to have options.
Yessir! It'll wake you up if you're not paying attention - that's for sure. After you do it a couple of times it's no big deal. The key is to be on level ground and have the tractor square to the trailer when you begin to climb. It could go to shit real quick it I tried to crab it on the trailer or the truck/trailer started to roll. Also, thanks about the videos. I have upgraded to the GoPro Hero 8 Black also. If I don't use that - I'll a 4K DSLR camera. Check out Biff's Equipment at ru-vid.com/show-UCOp1iElsFqVnWKVZc_A04rw. He got me into the GoPro. The out takes were my wife's idea. She could care less about tractors, but when she sees the raw videos and the out takes - she suggested that I add them in. They make her laugh! Thanks for your comment and for watching my video! Stay well!!
@@BotaTrac , you are like me. I just do the channel for a hobby and really enjoy it. I love watching other channels and have had a lot of fun with it. My channel is growing. I get a lot of views but not so many subscribers. The ones that I do get are pretty loyal to the channel. Thanks for the response and stay warm and well, not to mention safe. On a side note, you must be prior military as well. It would sure appear so.
Glad you like them! I'm always trying to improve the channel. I bought a video drone and I'm working on getting that involved too. I appreciate your comment and thank you for your support!! Please don't forget to like, share and subscribe!
Thanks! That seemed to be the highlight of this video for a lot of folks! I believe that anything can be done given enough time and motivation. I really appreciate your comment and taking the time out to watch my video! Stay well!! Please like, share and subscribe!
I like to condition my work boots too. I usually don't wear boots over my shoes as I like to travel light. One of the videos that I have done for my channel is "Tractor Talk With Gary's Best Buys". I show a pair of boots that I got from Cabellas. They have a unique fastening system that uses wire instead of laces. They fasten with a ratcheting system where you simply push in on the knob and turn to tighten and pull out to release. I got them when I was a volunteer firefighter for the speed and ease. Cabellas no longer carries these but Red Wing makes a shoe that has nearly the same fastening apparatus but it is a much heavier shoe and nearly double the price. Thanks for sharing Both Trac. Shoes are a very important part of the garb and a very poor place to be cutting corners.
And I couldn't be happier! You're a great guy with a great channel and I'm honored to have watching my videos. Thanks for watching, commenting and supporting - God bless!
I've been looking for exactly this comparison. I wonder if I should buy the grapple first, then my wife will say I HAVE to get the tractor for it, right? :)
Great point! Thanks for watching and commenting! Please don't forget to like, share and subscribe! Talk again soon.....good luck with the new tractor! LOL!😝
