EPB Rear Discs & Pads Without Using Any Diagnostic Scan Tools.

Подписаться 13 тыс.

Просмотров 73 тыс.

50% 1

MG HS, Replacing rear discs & pads without using a diagnostic computer to wind the caliper pistons back.
Before all the keyboard warriors kick off, yes I left the caliper hanging by the brake pipe, it weighs vertually nothing so it wont hurt it.
No brake grease. If it doesn't have any from the factory then I don't use any. Simples.
Right that's that out of the way, enjoy the vid.

Авто/Мото

Опубликовано:

16 фев 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 94

@blakemiller3078 4 месяца назад

Very well explained video. Getting ready to change out rear pads on my wife's '19 rouge w/ EPB. I wasn't sure about not having a scan tool. This helps me out tremendously! Thanks

@CyprianPhilogene Месяц назад

I used your method today, and it worked beautifully. Thanks for this video.

@marcvarga2087 2 месяца назад

thanks my friend - took 3 hours to find you... 2020 GMC AT4 6.2 💪😉

@017hamilton 8 месяцев назад

Brilliant, just what I needed. Thank you

@jaimelopez7801 3 месяца назад

very good video, excellent work. Thanks for sharing knowledge. greetings from Chile

@gazzafloss Год назад

Yes Steve, I was thinking, "now those discs don't look like the non ventilated ones that came off...brake upgrade, oooh". Great tip for the diy epb crowd, good one.

@pistonbroke Год назад

I didn't even look. I'd already done one side and the disc was right. Wasn't expecting to have one right disc and one wrong one.

@graham3282 4 месяца назад

Brilliant ! PBG Thank you from near London UK.

@pistonbroke 4 месяца назад

No worries 👍

@markholian3506 Год назад

The hose Steve! The brake hose we’re all going to die 😂😂😂😂😂

@pistonbroke Год назад

Started something now eh? I Should have said nothing 🤣🤣

@stuforbes3967 Год назад

Excellent video, thanks

@jeromeestrera8386 Год назад

Interesting tips for EPB.

@user-ti5en4ug2y 4 месяца назад

Just how I would have done it. Brothers got skills 👍

@stevewaghorn2029 Год назад

Totally agree about the brake flexi caliper hanging thing, never seen a problem. If the flexible brake pipes were that fragile, they should not be on a vehicle!. Thanks for another great tip Steve!.

@pistonbroke Год назад

If it's a big cast iron 4 pot caliper then i'll tie it up, they are a bit heavy. But a little caliper like this one, it weighs bugger all.

@markholian3506 Год назад

Sorry Steve, you got there before me

@train4905 4 месяца назад

Very nice job😊

@terenceparkinson3097 7 месяцев назад

Thank you very good video.

@mattyboy7807 3 месяца назад

Awesome video

@khaledeljanati 5 месяцев назад

Good work 👏

@nissanquest2002 Год назад

Great Video Sir , just my thought if disconnecting the battery terminals could help for the computer not to recognize the rear brake service and would it be convenience to do same time both Rr. LH and RH My point is not to have a check light pop up on the dash on normal driving for most viewers that doesn’t have a special scan tools .

@644jac Год назад

Does anyone know if there is a scan tool that can be used on MG cars. Mainly looking for MG3 use thanks.

@oldbiker9739 Месяц назад

not worry about brake hose with aluminum cast calipers , here in Canada in cold weather they carry many pounds of mud and ice on them all winter long , .

@kieranself9844 3 месяца назад

Legend

@Kampup 5 месяцев назад

Great video thank you, can this be done on a Hyundai 140 back calliper? what happens if the brake doesnt work? cheers

@pistonbroke 5 месяцев назад

If it has the same type of caliper as this then yes it can. I've never had one not work after doing this so I couldn't tell you.

@memedaddyz 4 месяца назад

amazing, man, does will it work same way on VW CC 2023. 2.0 Diesel manual gear?

@pistonbroke 4 месяца назад

If it has the same type of caliper as this then yes.

@johnharland2336 Год назад

Just reverse the polarity to the motor with a small 12 volt battery, which will depress the drive. No need to put apart the motor.

@pistonbroke Год назад

Quicker to wind it back than piss about with wires and a battery.

@Ally.MacMillan Месяц назад

The ECU in the car will stop the actuator when it meets resistance each way, the battery method won't, even if you are careful with a battery, you risk damaging the internals of the actuator. If you don't have a scan tool, phone app etc. then it's best to remove the actuator.

@simonwass6315 Год назад

Does connecting a power source to the motor terminals not work on this caliper? Also no one covers releasing the brake before commencing work, my car automatically engages it when ignition is off.

@pistonbroke Год назад

Quicker to wind it back than piss about with wires and a battery. You need to put it in service mode to stop the brake coming on. The procedure varies from one make to another.

@ThorEgilKittelsen Год назад

How do I put the mg's epb in service mode?

@pistonbroke Год назад

All doors closed, Engine running, seatbelt fastened behind your back so you can get out, foot on brake, release epb and hold switch down, turn engine off while holding switch down.

@ThorEgilKittelsen Год назад

@@pistonbroke Thank you. I have the electric version, the zs ev, but I'm hoping the procedure is the same. The caliper looks identical.

@eliezerbrito301 7 месяцев назад

It doesn’t damage the motor?

@edwardking9989 Месяц назад

How not to do calipers and pads,you never leave calipers hanging on brake pipes,where is the copper slip,no torque wrench.

@pistonbroke Месяц назад

Right, this really is the last time I'm going to say this. The caliper weighs fuck all, it aint going to hurt the pipe. Copper slip on brakes? You're one of them are you? I bet you put that shit on battery terminals too eh? Find me someone that uses a torque wrench on calipers. I've been doing this nearly 40 years, I know way more than you.

@johnmcminn9455 9 месяцев назад

Finally someone using an impact ...zip ...done

@michaelk3819 3 месяца назад

Great video, no p1ssing about. Gotta call you out tho, how the f are your hands so clean? Everybody goin on about hanging the caliper. The pressure this pipe handles under braking way out weighs hanging for a few minutes. Very helpful, thanks 🍻.

@pistonbroke 3 месяца назад

The caliper weighs next to nothing, if it was a big twin pot caliper then I'd support it. Dunno why my hands are clean, maybe the brakes just weren't that dirty.

@Antsummerfield83 5 месяцев назад

Is this the same on a 308 2019 with electric handbrake. I’m confused did you have the handbrake enabled to begin with or disabled as my 308 will auto enable it upon turning the engine off so I’m not to sure what I need to do

@pistonbroke 5 месяцев назад

You would need to put the brake into a service mode so that it stays off while you are working on the car. There will be a video floating about somewhere that will tell you how to do this.

@Antsummerfield83 5 месяцев назад

@@pistonbroke so as long as the parking brake is not on, I just need to remove the motor and then wind the piston back?

@pistonbroke 5 месяцев назад

Yes, you push the piston back and wind the drive on the back of the caliper.

@brandonbegay-yk6zd Год назад

How do u do it on a 2019 silverado 4x4 drive 1500 to change a brake pads on da rear brake

@pistonbroke Год назад

I don't know. We don't have the silverado in the UK so I've never worked on one.

@edwardmoody4253 Год назад

@@pistonbroke same way

@Darton-ok5xt Год назад

thank you

@connectlogic 3 месяца назад

another guy on here says you cant unplug the electrical connector or it needs sorting with diagnostic tool? is that right he was on a \hyundai i40. i dont want to unplug it and cause a problem.

@pistonbroke 3 месяца назад

As long as the ignition isn't on or the switch pulled while it is disconnected then it will be fine.

@salvadoralvarez2093 27 дней назад

Just tell the people what kind of car is that gracias de Guatemala..

@pistonbroke 26 дней назад

Doesn't matter what car it is as most will have the same type of caliper.

@caiprice6262 Год назад

Where is your garage located?

@pistonbroke Год назад

South Wales

@caiprice6262 Год назад

Have you got a work email I could send a inquiry to?

@kyraimack5788 Год назад

What size T socket is that ?

@pistonbroke Год назад

Can't remember, T40 or T45.

@DJP3stControl Год назад

@@pistonbroke T45

@joshdaniel-qs8oh 11 месяцев назад

What if piston is extended to far Can this still be done?

@pistonbroke 11 месяцев назад

Should be able to as long as it starts on the threads without crossthreading.

@joshdaniel-qs8oh 11 месяцев назад

@@pistonbroke not budging will go further out but not in

@pistonbroke 11 месяцев назад

@@joshdaniel-qs8oh wind the caliper till the screw comes to its stop then squeeze the piston back with grips or a G clamp. It should go back.

@joshdaniel-qs8oh 11 месяцев назад

@@pistonbroke anyway i could call you I been stuck here 4 hours trying 😭

@pistonbroke 11 месяцев назад

If it wont go back, lift the rubber boot and see if there is rust on the piston. If so then you need a new caliper.

@alexanderdowds1487 3 месяца назад

no torque values, no copperslip,caliper hanging by hose, impact driver for everything messy work

@pistonbroke 3 месяца назад

🤣🤣🤣 copper slip ffs. Bet you're the type that puts that shit on battery terminals.

@cessealbeach 6 месяцев назад

Shade Tree Techniques

@pistonbroke 6 месяцев назад

Whatever the hell that means.

@brian623 6 месяцев назад

Y u not use Greece on anything 😮

@pistonbroke 6 месяцев назад

Nope, unless it has grease from the factory, then I will.

@edwardmoody4253 Год назад

you should of cleaned the caliper up with brake clean and never hang the caliper by the brake hose says this ASE MASTER TECH.

@lamueljimmy338 Год назад

😮WoW less than 15mns, dealer at Rico motor home in Gallup NM will charge me $2,000

@sergeantmajordyi7049 11 месяцев назад

Cheers mate

@PatelJagCanuck Месяц назад

Thanks, but I won't let brake caliper hanging unsupported on its own weight. too dangerous for brake hose !

@pistonbroke Месяц назад

Whatever! I've already been through this god knows how many times. The caliper weighs next to nothing so it wont hurt the pipe. If it was heavy then I would support it. This is the last time I'm repeating myself.

@PatelJagCanuck Месяц назад

Good luck brother! I never wanted to challenge your skills. Wonderful video. Thanks

@nickgolding5786 12 дней назад

They were fronts

@javadkarimbeigi Месяц назад

سلام از آموزشتون سپاسگزارم ولی با اون آچار کلاغی به پیستون ترمزدستی آسیب میزنید و این کار غلطی بود

@pistonbroke 12 дней назад

I love it when people watch my videos because they don't know how to do something and then proceed to tell me that I'm doing it wrong. You couldn't make this stuff up.

@javadkarimbeigi 12 дней назад

@@pistonbroke شرمنده اگه ناراحتت کردم رفیق

@pistonbroke 11 дней назад

@@javadkarimbeigi you didn't upset me, I just find it ironic and amusing.

@Evil-Jesus 4 месяца назад

Gotta call you out, It's a little bit hacky. Don't let your caliper hang like that Number one, And number two, don't open up that motor if you don't have to. Just get a power probe and hook it up to the battery and reverse that motor.

@pistonbroke 4 месяца назад

Caliper weighs next to nothing so it won't hurt the pipe. I didn't open the motor, I took it off. As long as the seal is intact then it will be fine. Far quicker than pissing about with a power probe.