HOW TO REGEAR A SUPERDUTY DANA 60 (part 1) - Project Maple Leaf Jeep Build (no. 11)

Подписаться 15 тыс.

Просмотров 3,6 тыс.

50% 1

Learn how to regear a Ford Superduty Dana 60 in this video series. Part 1 will show you how to remove the factory carrier and pinion, how to install a new ring gear, and inner axle seals.
Please SUBSCRIBE to show your support! It’s FREE and allows me to continue building things to provide you guys with good content and work toward the vehicle giveaways!
Check out my website to see the brands I choose to support!
WarPaintoffroad.com
LINKS:
IMPACT GUN
www.amazon.com/dp/B01MCQ5VO1?...
FILE
www.amazon.com/dp/B07DNNYGS4?...
TORQUE WRENCH
www.amazon.com/dp/B07MKSJ4SG?...
BRASS PUNCH
www.amazon.com/dp/B00BNSIUU0?...
GLOVES
www.amazon.com/dp/B0001VNZQY?...
SPRING LOADED AUTO PUNCH
www.amazon.com/dp/B00004T7RF?...
DANA INNER AXLE SEAL PRESS
www.amazon.com/dp/B087WRCD2F?...
CASE SPREADER
www.amazon.com/dp/B06XDDZBS8?...
HOW TO DISASSEMBLE A SUPER-DUTY DANA 60
• HOW TO DISASSEMBLE A S...
***Disclaimer*** This video is just meant to show how I do it. Injury may occur by trying to replicate what is in this video. Attempt at your own risk, with proper equipment and training.

Авто/Мото

Опубликовано:

10 окт 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@BuildItWheelItExploreIt 4 месяца назад

Best explanation video ive seen yet!!! Thanks

@WarPaintOffroad 4 месяца назад

Thank you! I hope it helps. I made this because there are some others but they don’t explain it all that well. I am currently in the process of building a frame from scratch. That will be a fun one. Should be out in a couple weeks.

@petemiller519 Год назад

Hey Dan, once again great content. A little suggestion, don't worry about your videos being too long. You opted not to show the carrier in the vice, but if the viewer thinks the content is too simplistic, they can just skip ahead or fast forward the video. Your content is amazing, the more you show, the more relevant your content becomes.

@WarPaintOffroad Год назад

Thanks Pete! Love to hear the advice. I appreciate the suggestions. Always looking for ways to make them better.

@TomSmith-nx3hx Год назад

Once again, really well done! A ton of info that will help and guide anyone to take a job like this on. I've got two constructive comments... 1. When you knock the pinion seal off, use a chisel instead of a screw driver. They are sharp, which will help get under the edge, they won't get damaged, and it will be easier. 2. Use RTV to lube the inner seals into the tubes; they slide right in and any imperfections get sealed up. Awesome job presenting a LOT of highly technical information. You are diving into stuff that no-one has done before on the www.

@WarPaintOffroad Год назад

Great tips! And I love the idea of the RTV on the seals! I never thought of doing them like that! Great idea! Thanks for the support! The video on Thursday is going to be really good. As you know the pinion isn’t the easiest to set up. Especially the aftermarket pinion which gets depth shims on the other side of the inner bearing. So it gets a little complicated. But I think o explained it in a very simple way. Time will tell. Thanks again.

@TomSmith-nx3hx Год назад

@@WarPaintOffroad You're welcome and I look forward to it.

@TomSmith-nx3hx Год назад

@@WarPaintOffroad As I'm sure you know, setup bearings make life much easier for trial and error.

@WarPaintOffroad Год назад

@@TomSmith-nx3hx oh yea. That is in part 2.

@candycook3131 Год назад

You have some of the best how to videos on RU-vid when it comes working on JK installs.

@WarPaintOffroad Год назад

Thanks Candy! I have been doing it a long time. Just working in building the RU-vid channel and trying to give back. This jeep will be put on super flexy leaf spring suspension. It’s going to be reall wild getting coilover flex out of leaf springs.

@bassment03 Год назад

Super sweet

@WarPaintOffroad Год назад

Thanks for the support

@bassment03 Год назад

@@WarPaintOffroad sure bud you're killing it

@WarPaintOffroad Год назад

@@bassment03 working on it. Just trying to grow the RU-vid so I can continue to give back and do more stuff. But it’s getting there.

@mrbrettdimarco Год назад

Very informative 😎 one bite at a time

@WarPaintOffroad Год назад

Heck yea! Step by step!

@maverick_jl Год назад

BAD ASSSS!!!!!!!!! This is such great information.. I learn some S**T everytime I watch!!

@WarPaintOffroad Год назад

Thanks buddy! I appreciate that. Tomorrow’s pinion set up video will be good for people. It basically takes what makes the D60 so confusing and simplifies it. Just wait until I put leaf springs under the rig and get coilover flex! Going to be so cool.

@moejr14 5 месяцев назад

Where did you find the torch holder?

@WarPaintOffroad 5 месяцев назад

Tbh I don’t remember. But I’d bet you could find one on Amazon. I have had that for probably 10 years.

@moejr14 5 месяцев назад

Is it better to install/weld the truss before the gear install?

@WarPaintOffroad 5 месяцев назад

The only reason I would say no….is because it’s easier to drill the housing and install the air line fitting before the truss is on. But have it handy to determine where to drill or how to drill and notch the truss. I’ll be doing another set of axles soon here and going into all of that in detail.

@moejr14 5 месяцев назад

What about inner axle seals? Will they get torched with preheating the cast?