JOEL'S GARAGE GEAR 2 post 4.5 ton clear floor car hoist lift install and review | The Shed Sesh

Подписаться 1,3 тыс.

Просмотров 20 тыс.

50% 1

Hi guys,
This is huge. Not only the video length but "I have a hoist!!!". I go through the install of the hoist. Maybe in a bit too much detail, maybe not enough, but it should help you out if/when you purchase one. I did get a couple of questions after posting the last video but I hadn't got far enough into the install to answer.
Just a note to say this is not a sponsored video, I have no affiliation to Joel's Garage. I just love the fact they offer affordable options for well made Shed (Garage) Gear for the every day shmow!
Check out there range of Shed Gear at:
www.joelsgaragegear.com.au/
Specific featured hoist link is:
www.joelsgaragegear.com.au/pr...
Facebook: / theshedsesh
Instagram: / theshedsesh
Affiliate links:
Tools Warehouse: bit.ly/3t0pOke
Caravan RV Camping: bit.ly/3t1EqQl
Craft Cartel Liquor: bit.ly/3KuS9Fg
Hema Maps: bit.ly/3pUtd20
Mica Lighting: bit.ly/3MGLmdD
My Generator: bit.ly/3vXY9SQ
Olight Australia: bit.ly/3pVIzUi
Outback Equipment: bit.ly/3tO61np
The Man Shake: bit.ly/3hWaWx9
#theshedsesh #hoist #howto
Love your work! Now get in the shed!

Авто/Мото

Опубликовано:

1 июн 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 60

@joelsmith2905 3 года назад

Great video mate. We will take this on board and improve the instructions. As for the yellow lifting arms. The shorter 3 piece arms go to the front of the car generally. You can put the car either way but it's easier to have them to the front so you don't need to roll the car back and forward to get the arms under. Yes there is a Joel. Great job. 👍

@TheShedSesh 3 года назад

Ha, cheers mate. Thanks again for a great product ;)

@trevorthomas6013 2 года назад

I would have though that the short arms would go to the front of the car because that is were the weight is. Try to get the cg of the car to the centre of the post.

@dazzamac70 2 года назад

Great job mate! As a Work Health & Safety Advisor I was getting a bit nervous seeing you on the ladder and lifting that cross beam...🙈😆 You've inspired me to get my own hoist!!!👌👊

@TheShedSesh 2 года назад

Mate, I was a bit concerned myself. But I took all the precautions I could. To old to end up in hospital. Don’t bounce like I used to haha.

@vigorousvoices 3 года назад

Awesome video, Damo! Quite in-depth!

@kyleheppell2064 2 года назад

Very helpful video to help with the install of my JGG hoist. Cheers 🤙

@TheShedSesh 2 года назад

Glad I could help sir 👍👍😊

@MrCustomvs 2 года назад

brought one this week in Brissy. looking at a bulk purchase soon, pending quality. First impressions are great, along with phone ordering, easy and friendly, looking forward to seeing our hoist in use shortly. Thanx for the video.

@TheShedSesh 2 года назад

That’s awesome mate. You won’t be disappointed 👍

@Madbart66 3 года назад

Top video mate. My shed is going up next month with the hoist from Joel's soon to follow.

@TheShedSesh 3 года назад

Cheers bud. Good luck with it. Gotta love a good shed 👍👍

@EssentialOrigami 3 года назад

That is a nice looking hoist!

@TheShedSesh 3 года назад

Cheers mate :) She's a beaut!

@BADQ 3 года назад

Just stumbled across your channel, great work with it mate! Love the hoist install, Joel has an awesome hoist, I ended up opting for a different brand because of my height restriction I had, then they failed to deliver said height that was on their diagrams and had to go with their baseplate version, which sucked although the baseplate isn't as high as others I've used in the past so its not much of an issue. Ended up installing mine myself as well, very happy with it though, I also have a HQ coupe and it was scary lifting it for the first time also hahahha

@TheShedSesh 3 года назад

Awesome mate. Glad to have you along. You see the look on my face when the hoist clunked. I thought the q ee was gone. Haha.

@BADQ 3 года назад

@@TheShedSesh Hahah yeah those safety locks are are much louder than my hoist, would have freaked me out for sure!!! even freaked me out watching it a little haha

@bigal878 2 года назад

Good video mate. I’m now subscribed 👍🏻

@TheShedSesh 2 года назад

Cheers mate, welcome along. I’ll try and keep you entertained haha 😉

@TheRealPatrickStarOfficial 2 года назад

Couldn’t agree more about the amazing customer service after sale mate. My hoist turned up 2 weeks ago looking rather sad missing paint & wrapping all torn. I immediately sent photos and within 15 minutes I had a phone call & email response with the hoists paint code & reassurance of when it comes to installation if there are any issues to just reach out.

@TheShedSesh Год назад

That, right there, is awesome to hear. Hope she went up ok 👍

@TheRealPatrickStarOfficial Год назад

Went up like a dream. Have had plenty of cashies done on it already & currently got my partners kombi we're giving a birthday to on it now.

@TheShedSesh Год назад

@@TheRealPatrickStarOfficial outstanding 👍👍

@rixtrix11 9 месяцев назад

Put a very similar looking 2-post lift in my new "shop" as we call them in America. Can't wait to actually use it. Thanks for sharing your experience! Question: why are Aussie sheds uninsulated metal? Seems it would get terribly warm, or cold. Or is it a building code thing?

@lauchlanmenegon5916 3 года назад

Good job.. you did the cross beam a safer way than me. I had a ladder in between the posts, climbed the ladder with the cross beam on my shoulder and placed it on top. It was very dodgy I wouldn't recommend doing it my way.

@TheShedSesh 3 года назад

Haha, gotta do what ya gotta do but ideally a 2 man 2 ladder job 👍

@corybice6520 3 года назад

Glad I had a forklift for that part

@billyray4272 3 года назад

I just done the same can vouch it’s scetcky

@ezelk1337 3 года назад

Great job. Loved the explanation or all of the steps involved. I have a couple of questions. I am also going to install a second hand lift soon, How close is the driver side lift post to the wall? Do you have any problems getting out of the car with it that close? Also will you have to back in the car to say remove a driver side wheel. Thanks

@TheShedSesh 3 года назад

Hey mate. The hoist is a set width and if the car is in the middle you can get out of the car fine. The post is pretty close to the wall though but it only stops me getting between the wall and the post. But when the car is up in the air or on the floor I can get between the car and the post..... if that makes sense. On the wall side which if I drive th car straight in is the passanger side I have some shelves that are kind of in the way but I'd still be able to remove the front wheel, it's just a bit tight. I'd like to move some things around so I have a bit more room though..... I'll get there ;) The bay is 4 meters wide by 6 meters long...... ideally it'd be say 5 meters wide by 7 meters long but it is definately usable the way it is. You always need/want more space haha.

@KimboFromTheWest Год назад

How thick was your concrete floor? Mine is 100mm, thick enough for those anchors do you think?

@rixtrix11 9 месяцев назад

Cool car on the lift! What is it?

@CraigsAdventure Месяц назад

Any photos of Wire diagram for limit switch and possible motor if possible?

@pugmac6749 2 года назад

Hey mate. Enjoying you videos! I've ordered a Joel's hoist for my shed😎, a base plate model as i dont quite have the height. I have a bay 6mts long like yours. What distance do you have the post from your roller door?

@TheShedSesh 2 года назад

Awesome mate. I have them smack bang in the middle at 3 meters. I’ve run into an issue with putting the commodore on it though, driving in forwards, the spoiler hits the roller door roll at the top. Not sure if I can fix it by swapping the arms around. The front and back are different. But I’d probably have installed it say about 300mm closer to the back wall so giving say 3.3m from the roller door. But as I said, I may just be able to swap the legs and it’d be ok 👍 👍

@pugmac6749 2 года назад

@@TheShedSesh cool thanks. I'm aiming at 2.9 but reversing the car in. I might have to try to measure my car on another hoist ist. Thanks again 👌

@jimmyji2334 2 года назад

Quick question. Whats the clearance under the HQ (eg at sill height) when its fully up? Trying to work out if I can fit an clear floor or have to go a baseplate model. Cheers

@TheShedSesh Год назад

Jimmy, I let you down brotha. Just saw this. Let me know if you still need details.

@amanrandhawa3087 Год назад

Great video mate. I picked up a used one. Almost new. Will install next week. Did you use a 20mm drill bit? Thanks

@TheShedSesh Год назад

Sorry mate, just saw this. Assuming you’ve already installed. Can check the drill bit size tomorrow 👍 let me know 👍👍

@amanrandhawa3087 Год назад

@@TheShedSesh Thanks mate. Ye already installed. Your video was great help.

@TheShedSesh Год назад

@@amanrandhawa3087 great to hear mate 👍👍 enjoy 😊

@leonmissen2934 2 года назад

Hi did u have to change the hydraulic fitting on the pump it's changes side's in your video ?

@TheShedSesh 2 года назад

Hey mate, I did have to change from one side to the other as the fitting came in the wrong side. It was an easy swap. Any issues message Joel on their Instagram account and send photos. They help out pretty quickly.

@lachlanrowntree4412 2 года назад

Awesome video mate, super useful! The manual is terrible and glosses over way to much stuff.

@TheShedSesh Год назад

Mate, as long as it helped out a bit, I’m a happy man 👍👍 hope you’re enjoying it! 👍

@scottwatto 3 года назад

Good explanation video mate What is the overall height of the hoist, says on website need 3.8 but highest point is 3650

@TheShedSesh 2 года назад

Sorry mate, just saw this. Not sure of height will have to measure.

@scottwatto 2 года назад

@@TheShedSesh all good mate I bought one aswell

@tonymontana897 2 года назад

Good stuff mate. Can I ask, what happens when after you've measured and set the posts and start drilling, you hit rebar in the concrete ? What do you do then ?? Also, are the hydraulic hoses good quality and not that Chinese crap ?

@TheShedSesh 2 года назад

Hey mate, in regard to the rebar just keep on drilling. I was lucky enough to avoid them. May have skimmed a couple in a couple of the holes. Can’t talk to the hydraulic hoses. They seem well made to me. 👍👍

@tonymontana897 2 года назад

@@TheShedSesh Thanks mate. I'm going to be building my dream shed/man cave (9x15x3.6) and definitely going to install a hoist. All the best to you !

@Outback_Truckie Год назад

How is it still going? I am just about to pull the trigger on one very soon. Thanks

@TheShedSesh Год назад

Hey mate, still going good mate. Doesn't get heaps of use but it's doing well :) Go for it.

@Outback_Truckie Год назад

@@TheShedSesh Ok mate. I would have to get it sent to my Linfox yard and then I can get a tilt tray to deliver it to my shed

@mannycalavera121 2 года назад

Shed size and wall height? Congrats on the hoist

@TheShedSesh 2 года назад

Hey mate. Cheers. Shed is 6 x 12. Each bay is 6 x 4. I reckon a perfect minimum for a bay would be 7 x 5 but it works. Better than not having a hoist haha.

@TheShedSesh 2 года назад

Forgot to mention. Wall height is 3m to the eves with a harsher than usual pitch on the roof.

@mannycalavera121 2 года назад

@@TheShedSesh cheers man. Building a house atm, looking at 12 x 9 3.6m walls. Good to see it all fits nice. Like you, bout time I got myself a hoist lol.

@iamasmurf1122 2 года назад

Anything to Do with cars is a lose lose system financially ! I have a nice car ; I do work on cars myself but geez people I have to say after buying all the tools … people complaining about the price over and over it’s not a trade that’s really worth doing … I make more money investing in crypto than anything Automotive