JUMPER R1 RECEIVER TELEMETRY SETUP

Подписаться 11 тыс.

Просмотров 24 тыс.

50% 1

JUMPER R1 RECEIVER - Today I take a look at the Jumper R1 full-range telemetry micro receiver and compare it’s physical characteristics and specifications to the FrSky R-XSR telemetry receiver. I’ll show you how to connect it to your flight controller with a detailed flight stack connection diagram then demonstrate how to set it up for telemetry in both Betaflight and your OpenTX transmitter, to include providing you with an easy-to-follow, step-by-step graphical checklist you can download through a link below. And, if you need a refresher on how to set up RSSI in both Betaflight and your transmitter, I’ve got your back on that as well with another Free BONUS RSSI Setup checklist also available through a link below. I’ll wrap things up with side-by-side received signal strength indicator (RSSI) comparison flights using the Jumper R1 receiver and the FrSky R-XSR receiver. Interested? 😉
Thanks for Watching! Please share the video with your friends. Your comments below are highly encouraged and greatly appreciated!
New or relatively new to FPV or a more experienced pilot looking to help others entering FPV? Enroll in our Fast Track FPV Course! 🎓 Learn more to include a complete course description and the detailed Course Curriculum through the link made available below!
⭐ FAST TRACK FPV COURSE: tmacfpv.thinkific.com/courses...
⭐ MORE FREE FPV LEARNING RESOURCES: tmacfpv.com/
✔️FREE Micro FPV 3" Frames Guide: tmacfpv.com/micro-fpv-quadcop...
👉 Join and Support YOUR TMacFPV Team at: / tmacfpv
👉 email: TMac@tmacfpv.com
TABLE OF CONTENTS
00:00 INTRO
00:39 R1 & RXSR physical characteristics & spec’s comparison
04:03 R1 flight stack connection diagram
05:49 Betaflight telemetry setup
08:56 Transmitter telemetry and voice warnings setup
13:12 RSSI comparison flights
JUMPER R1 GIVEAWAY RULES - winner will be announced Friday, Dec 13, 2019
FREE SHIPPING WITHIN U.S.
1. Subscribe and ensure subscriptions are public (for verification purposes) on Dec 12, 2019 2. Hit the bell (above) to be notified of each new TMac FPV video
3. Comment on this video below and include #flightpath2fun
RU-vid is not a sponsor of this contest and by entering you hereby release RU-vid from any and all liability related to this contest. Entries which do not comply with RU-vid's Community Guidelines ( ru-vid.compolicie... ) will be disqualified.
PRODUCT LINKS: Some (or all) of the following are affiliated links--when you use them to make ANY purchase (not just the linked product), at no additional cost to you, it supports your TMac FPV Channel & enables TMac FPV to earn small referral fees through affiliated sites. They are here for your convenience & there is no additional cost to you for using them.
Banggood: www.banggood.com/index.php?zf...
Airblade UAV: bit.ly/2vxQttS
ReadyMadeRC (RMRC): www.readymaderc.com/?referral...
FlexRC: flexrc.com/?wpam_id=48
HorusRC: www.horusrc.com/en?acc=13396
HobbyCool: hobbycool.com?afmc=9y
Tubebuddy: www.tubebuddy.com/TMacFPV
👉JUMPER R1 RECEIVER:
Banggood (China): www.banggood.com/custlink/K3K...
GetFPV (U.S.): www.getfpv.com/jumper-r1-d16-...
Grayson Hobby (U.S.): graysonhobby.com/jumper-r1-16...
Flying Tech (UK): www.flyingtech.co.uk/electron...
Phaser FPV (Australia): www.phaserfpv.com.au/products...
👉HOBBYMATE D16:
Amazon: amzn.to/2OCQljz
HobbyCool: hobbycool.com?afmc=9y
TheFPV The R1 Frsky D16 Compatible Receiver (UK - UnmannedTechShop): www.unmannedtechshop.co.uk/pr...
RESOURCES & LINKS MENTIONED IN THIS VIDEO:
⭐Jumper R1 Telemetry Setup Checklist & Connection Diagram: tmacfpv.com/jumper-r1-telemetry/
⭐RSSI Setup Checklist: tmacfpv.com/jumper-r1-rssi-se...
⭐CLI Useful Commands Video: • BETAFLIGHT USEFUL CLI ...
⭐Jumper T16 Pro Custom Sounds: • OPENTX CUSTOM SOUNDS
👉 JUMPER T16 PLAYLIST: • JUMPER T16
MUSIC:
Creo - Rock Thing (Copyright Free Music)
Creo: / creo_music / creo / creosound creativecommons.org/licenses/... Music provided by RFM: • Video
#jumperr1, #d16receiver, #jumperxyz, , #jumpert16, #opentx, #multimodule, #t16pro, #jumpertx, #tmacfpv, #beginnerfpv, #fpvbeginner, #radiocontrol, #rchobby, #fpv, #fpvlife, #dronelife, #flightpath2fun, #fasttrackfpv, #learnfpv, #drone, #quadcopter, #multirotor, #fpvracing, #rcgroups, #quaddiction

Наука

Опубликовано:

21 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 142

@TMacFPV 4 года назад

What do you think? Is the R1 the perfect match for the T16, or for that matter, ANY D16 compatible transmitter? Let me know YOUR thoughts below. Thanks for watching and your support of TMac FPV! Clear Skies friend! 👍😀

@Barnz1980 4 года назад

They both clearly seemed like the best choices from any brands atm, all the features & the right prices.

@macelius 3 года назад

Next build is getting one for sure!

@h2o40fpv 2 года назад

The good things about old videos is that i cant always go back to get information about almost anything that I need to keep my drone on the air. Thank u Tmac.

@turboomni848 4 года назад

Thanks for the great info. When I get my Jumper your channel will be my first to go place for tutorials and answers. Subscribed

@TMacFPV 4 года назад

You're quite welcome Turboomni! 👍

@Sackenstein 4 года назад

Great video TMac! Glad to see there are other options for recievers. Looking forward to next video. Thanks

@TMacFPV 4 года назад

Quite welcome Lawrence! Hope your update goes well for you friend. Let me know how your Crossfire works for ya!👍Keep pluggin' away on your "Journey to Better FPV Fun!"🤩

@Barnz1980 4 года назад

Cheers Tmac 🤘, just got into FPV 2 months ago. You helped me hook up the R1+ to an Eachine Tyro79 with a Jumper T16. I used the Tx2 pad & went through cli like you showed 👍.

@TMacFPV 4 года назад

Outstanding Barnz1980! Thanks for sharing your success story! Happy Flying Friend!😀

@FauziNS 4 года назад

Crystal clear explanation and tutorial. Just got my r1, and you helped me with this great vid, as always. Thank you TMac!!

@TMacFPV 4 года назад

That's great to hear Fauzi NS, you're quite welcome! 👍😀

@sillysmoothfpv3666 4 года назад

Great video!!!! I'm glad I discovered your channel two weeks ago.

@TMacFPV 4 года назад

Thanks Darrell! Welcome aboard!😀

@MarkTurkel 2 года назад

Thank you, sir. The downloads are very helpful as well.

@PhAtlPrints 4 года назад

An awesome resource, keep the videos coming

@TMacFPV 4 года назад

Thanks PhAtlSun! Appreciate you taking the time to provide your feedback. More to come this afternoon!

@knightshado 4 года назад

Excellent video. Keep up the excellent work.

@TMacFPV 4 года назад

Thanks Edward, I truly appreciate you taking the time to comment. Have a great weekend friend!😁

@joshuajshmrh2473 4 года назад

Sir, you are one hell of an instructor.

@TMacFPV 4 года назад

Thank you Joshua🙏I truly appreciate your support 👍

@jacobxu 4 года назад

So helpful for me, Thank you bro

@Sub250gFPV 4 года назад

I've learned a hell of a lot from this video TMac Thank You 👏👏👏 and apart from the obvious info i've also learned that :- 1. FrSky is on the way down 2. The Jumper R1 improves the VTX image 🤣🤣🤣 3. You have beautiful Thumbs 😂😂🤣.

@TMacFPV 4 года назад

Ya got me on that last one mate! Couldn't stop laughing 😆👌

@W0KNI 4 года назад

Great job! Thank you sir.

@DUKE0010 4 года назад

nice video very interesting on the t16 stuff and accessories you explained it very clearly thank you for all your videos just got my 3 weeks ago t16 and don't know where to start with all these features firmware and accessories

@TMacFPV 4 года назад

Thanks Frank! Might I suggest to just "start" in between many, many awesome flights!😉😁Have a great weekend friend 👍

@kyon_03 3 года назад

Your tutorial are so useful :D

@TMacFPV 3 года назад

Thanks Paul🙏 Happy to hear they're helping out a little

@ikarus126 4 года назад

Excellent video, thanks for your efforts. I wonder if jumper rx has same range and reliability as r-xsr?

@TMacFPV 4 года назад

Range? Perhaps better! Reliability? No issues so far, we'll see😉

@h2o-fpv623 4 года назад

Great video thank u for the info.

@TMacFPV 4 года назад

You got it H20-Lobo! Thanks for your comment friend!

@vinceywinceyspider 2 года назад

Would you know how to set up on inav. I'm new to this. I cannot get telemetry on my t16s. I'm using an f4 fc. Eachine tyro quad. I soldered to the sbus tab on the underside. And tried tx5 and tx4 for s port. Switched it on in ports tab. My transmitter finds only 4 basic sensors but is receiving telemetry. I've not shorted the 2 tiny tabs for inverted as I think not needed using the underside connection that says sbus Or am I wrong. Any help appreciated as I'm going mad now lol. Thanks

@FPVDiverBomber 3 года назад

I tried hooking up my r1 via sbus to my old Mantis F3 FC, but the signals were jumping all over the place in beta flight reciever tab? I never like to try to fix things that are working,,, My Flight controller is old and wont update so I went back to using it as it was with old spek sat... But I wonder what the problem was and if there is an ez fix? I see you video and think I could try putting the r1 on a different urt,,, but the mantis manuel says the sbus is where you connect sbus soI'm stumped...

@junebugpetty7386 4 года назад

Great videos

@TMacFPV 4 года назад

Thanks Junebug! Have a great weekend friend!😀

@christopherbigelow1323 3 года назад

I have Mamba F405 MK2 Stack 30x30. It has an RSSI pad, but no s.port. My receiver is R1+. Can I use the rssi wire?

@bayuocta7042 2 года назад

Hi Tmac, thank you for those awesome videos, i just want to ask about incorrect rssi value in my OSD display. It always displayed "99" and never change at all. But ive already have correct value in my jumper T12. Cant yoy tell me what isnt right? (I used junper R1F + T12 remote) Thanks a lot

@TMacFPV 2 года назад

try these few things ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-egVxZuyoxho.html If you're using an F4 flight controller, check this out ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hwJtnkVq274.html

@shinuza 4 года назад

Great video, and dude... I didn't even know you could add a table of contents to videos on RU-vid...

@TMacFPV 4 года назад

Thanks Shinuza San! Yes, you can. I do it to help my viewers out when I have a longish video. Most content creators do not because it tends to decrease watch time (people then have to hunt for places in the video manually which increases watch time)

@shinuza 4 года назад

@@TMacFPV And then, the top comment is a dude listing each sections with timestamps 😂😂 Anyway, I ordered two of those using your affiliate link as I trying to get away from FrSky's stranglehold. Bonus: your schematics including audio wiring is huge help!

@luismanchego6856 3 года назад

I am building a 3" quad and using the mamba mini MK2. It came with betaflight 3.5.1. Do you think is worth updating to 4.1or higher? People reported some problems with the update... Have you updated it? If so, what do you think? By the way really helpful video, thanks Tmac👍

@TMacFPV 3 года назад

Hey Luis! I'm running BF 4.2 on all my micro's with RPM filters. The RPM filters to me are very much worth updating. When you enable them correctly, they get rid of all motor noise from gyro. Having said that, I do no know your level of experience. So, this video may help guide you a bit if needed (its the last micro build I did and goes through most, if not all, of the stuff you need): ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-4KUz4Z8ejTA.html

@normanjeckel9502 4 года назад

Thanks for the video and all the info , love my t16, can't wait to try one of these out #flightpath2fun

@TMacFPV 4 года назад

Hey Norman! You're welcome & good luck friend!😀

@seba2038 2 года назад

what is the distance to operate this receiver on plane? I am using Jumper t8SG.

@eruktationcx14 3 года назад

Can I see the rssi without soldering the rssi wire to the board or can I see rssi with only the sbus wire?

@TMacFPV 3 года назад

Please see 4:03 of video

@bennedictbyy 3 года назад

Hi there, I would like to ask a question, recently I accidentally broke one of the antenna on the Jumper R1 receiver. However, I am not sure what is the name of the antenna for replacement. Is the antenna on the Jumper R1 an IPEX connector or an UFL connector? or neither? I am very confused. Thank you very much in advance.

@TMacFPV 3 года назад

See this link and scroll down to "Replacing R1 Antenna" www.graysonhobbyshop.com/jumper-r1-drone-receiver/

@olMadMaxlo 4 года назад

TMac, hello good sir. Have you had any range issues with the R1 or the R1F? I picked up 2 of each from Grayson Hobby and all four of them had me pulling my hair out for over a month. My range in optimal conditions for all four of them is 100 feet before RSSI starts to plummet and i mean fast right to failsafe (90 rssi to 50 in a couple seconds). I bought new tx antenna, new rx antenna, A NEW TX (had Jumper t16, picked up a T12) installed on multiple quads in every mounting possibility imaginable, even mounted as incorrectly as i could just because, mounted them 1 foot off the quad on a stick to get completely away from everything on the quad, incrementally trimmed antenna through the "range" of lengths trying to tune it...........I could go on. And yes, flown in optimal conditions, perfect line of sight, no rf interference, flew friends bird same day no issues (xm+). I picked up xm+ and installed it and what do you know, I can fly to the end of the field, into the next field and oh happy days. But whats the deal with the jumpers? Four lemons! No way....right? Sorry for the long comment. Tried to keep it short while answering what i know people are going to ask. Is there anybody out there with this issue? Thanks y'all and thank you TMac for your superb videos.

@TMacFPV 4 года назад

I have not had any issues with the R1 receivers I have used the few times I have used them. I normally fly Crossfire. Additionally, a fellow pilot I gave an R1+ to reported he got 1.7 miles of range with it (and could have gone farther if not for his VTX limitation) on a fixed wing. This was back in December of 2019, so perhaps something has changed since then?

@olMadMaxlo 4 года назад

@@TMacFPV Yeah I made the jump over to crossfire as well (which is awesome), and thanks for you vid on signal strength. I'm baffled with these jumper receivers. I haven't heard back from Grayson Hobby which is dissapointing. Maybe that's why they were so cheap ($10 each) but I doubt that they would willingly sell a bad batch if it were. I might fiddle with them again and if I get the same results maybe I'll send you one as a sanity check if you would be willing. Thanks for the reply and take care.

@samavella8831 4 года назад

Hi, Thank you for the excellent video. I’m very new at this, and very reluctant to do my own modes and installs. I have a brand new Beta85X with a faulty Frsky FCC receiver and BetaFPV is giving a hard time in that because I’m in Canada they are only offering me a $25 refund - crazy night!! I’ve been dealing with their support for over a week and this is all that they are offering. I was thinking that maybe I purchase another receiver and have installed by a local hobby shop, hence my following question! Can this receiver be installed on the Beta85X HD 2S-3S version and still get the full range of telemetry? Thank you

@TMacFPV 4 года назад

Hey Sam! You're welcome. Let's see if I can help. Just did a search for your version of Beta85X HD 2S-3S. If its the original version (which I believe is what you're talking about) and does not have the F4 V2 flight controller but has the original V1 instead, here's the link for the flight controller: betafpv.com/products/f4-2s-brushless-flight-controller-and-esc . What this link shows me is you have a 5v pad, a ground (GND) pad, an SBUS pad, and a spare UART TX pad (the 4 pads I mention in this video). That's all you need for this telemetry receiver. So, "Yes" it will work. It MAY be a little big in physical dimensions for that size quad though. If you only want/need RSSI displayed on your OSD in your goggles, the XM+ is a smaller size RX. If you want/need the voice alerts you may want to go with the FrSky R-XSR which you can get at SH Hobbies up there in Canada at this site: www.snhobbies.com/advanced_search_result.php?keywords=frsky+r-xsr . As mentioned in the video, the connections for the R-XSR and the Jumper R1 are the same except the SBUS and S_Port wires are swapped. Hope this helps Sam. Clear skies friend!

@samavella8831 4 года назад

Hi TMac, You’re the best. This is the first time I received such a detailed answer to a question and so quickly. I like the second option of the Frsky R-XSR. All I would need is to have my local hobby shop install it. I would love to join your patronage.

@TMacFPV 4 года назад

@@samavella8831 You're very welcome Sam, happy to help friend. You may want to check out the Fast Track FPV Course on a page of my website at tmacfpv.com . Might find it useful. Other cool resources are there too! In any case, good luck and let me know how it goes; Clear skies!👍😁

@hanquah 3 года назад

Hi sir this jumper can bind to good ol accst qx7 radio without problem? Im thinking of switching to this wonder if its work with accst qx7

@TMacFPV 3 года назад

Hey HelioGenesis-HS! I believe the Jumper R1+ receiver comes with the ACCST D16 protocol firmware prior to FrSky updating all their ACCST stuff to version 2.1. So, if your QX7 firmware has not been updated to the new ACCST ver 2.x firmware, it should work fine with the Jumper R1. It will definitely not work with ACCESS protocol transmitters

@hanquah 3 года назад

@@TMacFPV ahh nice. Thanks for clarification

@GeezerGramps 4 года назад

Another informative video TMac nice that Jumper also has rx though we can use most of what’s out there. #flightpath2fun

@TMacFPV 4 года назад

Thanks Gramps Ramblings! Yep, with the T16, we're fortunate to be able to use can whatever suits our needs! Very nice to have options 😊

@entertainmentunlimited3256 2 года назад

Which is better? R1F of R1 V2 Mini. What is difference between R1F and R1?

@Grumpyoldtwit 4 года назад

If my full size mamba F405 DJI stack has an RSSI pad, should I still not connect the RSSI cable? I’m having difficulty trying to find some guidance on hooking up my R1 rx to the full size mamba DJI stack. The pads in the ‘receiver’ part of the flight controller, according to the card that comes with the FC are: GND 5V RC Invertor[TX1] Uninverted[TX1] RSSI There is a note re; ‘RC’ that says (TBS/SBUS/IBUS/DSM(RX1) It’s all Russian to me. Could you clarify the connections for me please?

@TMacFPV 4 года назад

Receiver GND goes to Flight Controller (FC) ground, Receiver 5V goes to FC 5V, receiver SBUS goes to FC 'RC' (which your documentation shows as SBUS along with the other TBS/IBUS/DSM protocols). Receiver SPORT goes to the pad right next to the 'RC' pad which is labeled SPORT in your FC wiring diagram documentation you can find here bit.ly/MambaF405DJIFC_Diagram

@Grumpyoldtwit 4 года назад

Thanks for the wick reply TMac. Hmmm. It’s not labelled SPORT in the wiring diagram I’m looking at. Mine says Invertor (TX1) and Uninverted(TX1). That’s why I asked the question.

@TMacFPV 4 года назад

ok Muzz, no problem. The pad next to the 'RC' pad in the wiring diagram on the site URL I gave you shows as the SPort pad (in yellow writing). If your documentation does not show that, your SPort signal from the R1 is inverted which means you need to connect it to the dedicated "Inverted" TX1. This will then uninvert the signal (i/e/ 2 inverts = 1 uninvert)

@guguslangit2230 3 года назад

why my rssi still in 90-85, even in my remote was RSSI low

@lofifpv6814 3 года назад

Hi! I followed this guide but am unable to get any stick input to show in Betaflight. I have confirmed that the rx is bound to the radio, so it seems to be an issue between the R1 and the FC. I am using the Mamba F405 Mini. Any ideas?

@TMacFPV 3 года назад

When connected to Betaflight (with props off) do you have your quad powered with a LiPo also? Some flight controllers require to be powered with LiPo also for receiver to be powered while connected to Betaflight. Check to make sure your R1 receiver RX pad is going to TX pad of flight controller and R1 receiver TX pad is connected to flight controller RX pad of the same UART

@lofifpv6814 3 года назад

@@TMacFPV Yup, lipo is connected and receiver is giving the correct lights. According to the diagram for the FC everything should be fine. gnd to gnd, 5v to 5v, sbus to sbus and s.port to ppm.

@TMacFPV 3 года назад

@@lofifpv6814 ok, a couple more things to check . . . .since you connected to the PPM pad, did you enable softserial for it per the video? In Configuration Tab of Betaflight did you enable Serial Based Receiver and below that, select SBUS? in the PORTS Tab of Betaflight did you toggle on Serial RX for the UART you've connected your receiver to? Make sure to click on Save button in Betaflight after each change you make. Only other thing I can think of is perhaps you held the bind button down too long (see this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Wx24PQ0sceI.html )

@rogergravel6638 4 года назад

Thank t mac your the top

@TMacFPV 4 года назад

Thanks Roger! Very much appreciate your support!🙏Have a an outstanding weekend and a very Merry Christmas 🎄

@stuartmacdonald6754 4 года назад

hi Tmac would this apply to an RXSR RX and a T16 as well? i have an RXSR in my quad and only see a few sensors and things like VFAS are missing even when i try to discover them.

@TMacFPV 4 года назад

Yes, should be the same type of setup. I mention this between 4:43 and 5:09 time marks of the video. The SBUS and S_Port wires of the R1 and the R-XSR are swapped. Other than that, connections should be the same. Some flight controllers have an S_Port pad and you don't need to use a spare Tx pad or PPM pad and go through remapping, etc. I've got a checklist you can download in the video description if you'd like. Also, you need to pay attention to what firmware you have loaded on the T16 multi-protocol module. You should be able to update your MPM firmware using the process in this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-EJx9mz-DI_g.html Reason ot do it is if your R-XSR has FrSky ACCST D16 V2 firmware on it, you'll need version 1.3.0.91 or newer firmware since the MPM didn't work with ACCST D!6 V2 receiver firmware. Of course, there's not way to know what firmware you have on your receiver really unless you put it there. With MPM firmware 1.3.0.91 or newer, you'll either want to use FrSky x or FrSky X2 protocols on your MPM when binding to your receiver. That's explained in this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-y6wg-_PmiL8.html

@stuartmacdonald6754 4 года назад

@@TMacFPV thanks TMac. i actually got hold a Jumper r1 today and have updated firmware to 2.01 via the t16 which appeared to work perfectly. i have connected the R1 to my mamba mini board in the same config as you describe in you video however i am unable to get the R1 to bind to my t16. T16 is running latest firmware as is multimodule and i am trying to bind to R1 using the new FrskyX2 protocol to match the version of the firmware i put onto the R1. the R1 goes into bind mode at boot (solid green and red leds) but i never get any response (flashing) from the LEDS when attempting to bind from the t16. ive tried changing the fine tune settings to vairous points along the scale (+ and -) but still no joy. any ideas?

@stuartmacdonald6754 4 года назад

update Tmac....ive got it to bind now but i had to do two things. i reflashed the firmware from EU LBT to FCC as i read somewhere that these R1s only support international (FCC) firmware. I then tried binding using Frskyx2 again but got nowhere and then tried the normal Frsky D16 and it bound straight away!

@user-nl4xv2fr6k 4 года назад

Hello, i need help! I'm connect SBUS only and i get RSSI only, but RxBatt is 0.0V. Can i get RxBat without S.Port connection? Sorry for my English i'm from Russia.

@paulh7189 4 года назад

Алексей Макаров read this thread: www.rcgroups.com/forums/showthread.php?3407837-Jumper-R1F-Receiver-two-way-full-duplex-Sbus-Compatible-Frsky-D16-Mode-Radio-support the voltage divider on the rx is wrong jumper switched the resistors!

@skyzeus3198 3 года назад

Thanks sir. pls show how to make omnibus f4 v3 smartport telemetry by using Jumper R1 receiver.

@TMacFPV 3 года назад

Here's a video using the Omnibus F4 v3. Just remember the R1 wiring is different than the XSR. See my video you commented on here as to how they are different ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-umokmFLR3wM.html

@user-bh7fb5cp3h 4 года назад

I hope your channel grows fast... #flightpath2fun

@TMacFPV 4 года назад

Thanks friend!

@davidchillton1744 3 года назад

Helpful tip if buttons stop working on your jumper ( unplug and replugin the ribbon cables that go to the buttons that stopped working)

@OrLove13 4 года назад

Спасибо большое ,помогло.

@TMacFPV 4 года назад

пожалуйста 👍😀

@OrLove13 4 года назад

@@TMacFPV Если по русски то будет правильно ,"не за что " 😁👍

@TMacFPV 4 года назад

@@OrLove13 Я попытался . Спасибо 👍

@TheSolla45 3 года назад

Is this this reciever compatible with the taranis x9 lite with the accst D16 mode?

@TMacFPV 3 года назад

The "newer" version of this same receiver comes from RadioMaster. Its the RadioMaster R161 receiver that uses the ACCST D16 protocol. In the images, it appears big. It is not. That's just the plastic case it comes in. That plastic case separates (opens) and inside is the exact same receiver (Jumper R1) you're looking at. It can be found on Banggood here (affiliate link): bit.ly/RadioMaster_R161_RX OR at RacedayQuads (only $9.99) here: www.racedayquads.com/products/radiomaster-r161-sbus-d16-2-4ghz-rc-receiver OR at DefianceRC (Alabama, U.S.) here: www.defiancerc.com/products/radiomaster-r161-16ch-frsky-d16-compatible-sbus-s-port-receiver?_pos=1&_sid=73ed0e676&_ss=r

@TheSolla45 3 года назад

@@TMacFPV In the description it says it's frsky D16 compatible does that mean is ACCST 16?

@TMacFPV 3 года назад

@@TheSolla45 yes ACCST D16 is an FrSky protocol. It's the exact same thing

@michaelsantoro9670 3 года назад

Why can’t I bind my R1 receiver to my Taranis X9D+ access Radio?

@TMacFPV 3 года назад

Your R1 receiver doesn't use ACCESS protocol, it uses ACCST D16 (FrSky D16) protocol

@devingable8467 4 года назад

Will this work with the R9 Frsky module?

@TMacFPV 4 года назад

R9 is a 900Mhz system. This is a 2.4Ghz receiver so, no it will not

@coolboarder654 4 года назад

If your receiver has an inverted SmartPort signal like the Jumper R1+ then make sure to set the tlm_inverted = off. Run these two commands: set tlm_halfduplex = on set tlm_inverted = off

@shogo8633 3 года назад

I can only see TRSS, TQly, RSSI and RxBt (showing 0V by the time..) what can I do?

@TMACFPVShorts 3 года назад

Try using the telemetry setup checklist available in the video description above under Resources & Links Mentioned in This Video

@shogo8633 3 года назад

@@TMACFPVShorts Hi! Thanks for your response. I did everything step by step but I only can see 4 sensors and rxbt 0V. What else can I do?

@TMacFPV 3 года назад

@@shogo8633 Fernando, Here3 are some things you can check (if you wired it correctly, and set it up correctly in your transmitter and in Betaflight it should work fine). As I have no ide what transmitter or flight controller you're using, perhaps its a limitation of one (or both?) of those. Try checking th efollowing: Is it the Jumper R1, the Jumper R1F or a different receiver? Did you make the connections from your receiver to the flight controller as indicated at the 4:04 time mark of this video? Did you set it up in Betaflight per the instructions at the 5:49 time mark of this video and also in your transmitter per the checklist (Discover New Sensors)? Do you have RSSI set up in your transmitter as an Input Line and also as a line in your Mixes Page?

@shogo8633 3 года назад

@@TMacFPV Hi again! It´s a Jumper R1, Radiomaster T16 and omnibus F4 clone from aliexpress. I also tried with a ZEUS F722 and I get more sensores but rxbt shows 0V also so I think I have 2 problems.. Jumper R1 not sending any voltage measures and the omnibus F4 port reversed or whatever. Yes, I checked the video and the guides a lot of times. I wired it with the soft serial method. I am able to get the rssi measures. My problem is that I only get 4 sensors with the f4 board (a lot more with the f722) and Rxbt shows 0V

@ruftime 4 года назад

Thanks TMac! Technically the R1 is 60% larger than the r-xsr and many micro receivers.... fine for 3” heavyweights and up:-)

@TMacFPV 4 года назад

You're welcome Canyon Racer. and 67% heavier! Doing math in public again, I gotta stop that!😁

@lucan3361 3 года назад

How do you bind this receiver?n I have been having a bit of a problem.

@TMacFPV 3 года назад

"Binding method: Press and hold the receiver's bind button, turn on the power (i.e. plug in the LiPo with bind button depressed), the receiver will now enter binding mode. The red light is always on and the green light is flashing slowly. Turn on the remote control and begin the bind procedure according to your radio. After the bind is successful the red light is off and the green light is always on."

@lucan3361 3 года назад

@@TMacFPV When I plug in the lipo with the bind button held down, the green and red light are solid. Is there something wrong?

@TMacFPV 3 года назад

@@lucan3361 Are you attempting to bind in FrSky X or FrSky X2 sub-protocol? Should be FrSky X (if you did not attempt to update firmware). Have you attempted to finish the binding process even if both lights are solid (it might work)? Sometimes the lights don't always match the instructions. I always turn the radio on first. Then get ready to hit "bind" in the radio. Keep the bind button pressed while you power up the Lipo/receiver. Hit "bind" on your transmitter, then I select ch9-16 telemetry On. Sometimes the lights don't always match the instructions, however, if you use this process, to include FrSky X, and it doesn't work, check your connections and solder joints to make sure two are not connected together. The bind process should be the same as in this short video (it appears to be the same receiver re-branded). ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-1K7QpjJO_s0.html

@TMacFPV 3 года назад

Use RadioMaster's R161 instruction manual (its the same receiver). RadioMaster has better "customer support/user manuals). User manual is here: drive.google.com/file/d/1KiPtPaTAoMKRd1g9-0IfgLyfwrdGNa_-/view

@MrChefpilot 4 года назад

#flightpath2fun awesome job

@TMacFPV 4 года назад

Thanks MrChefpilot! Appreciate your support friend 🙏

@entertainmentunlimited3256 2 года назад

Hello sir, how to wire Jumper R1 V2 Mini receiver. It has 3 wires. I can't find any guide for it. I am new to hobby and this is my first built. I am using F3 flight tower.

@TMacFPV 2 года назад

See SBus, VCC, and Ground connection under Full Description" of this link usa.banggood.com/JumperRC-R1-V2-Mini-2_4GHz-16CH-Over-2KM-D16-SBUS-Full-Range-RC-Receiver-Compatible-T-Lite-T18-T16-T12-T8SG-Radio-Transmitter-for-RC-Drone-p-1894214.html

@entertainmentunlimited3256 2 года назад

@@TMacFPV I know about this. Can you tell me where sbus wire connect on flight controller?

@TMacFPV 2 года назад

@@entertainmentunlimited3256 SBus pad if your flight controller has one or try RCin pad if it has that. Check your specific flight controller's documentation on its product page (or manual in came with) for how to connect a FrSky protocol receiver to it

@entertainmentunlimited3256 2 года назад

@@TMacFPV can I wire sbus to RX of the controller?

@TMacFPV 2 года назад

@@entertainmentunlimited3256 yes

@Gabe-reis 3 года назад

thank you thank you thank you thank you thank you thank you thank you thank you thank you

@TMacFPV 3 года назад

😂 you're very, very, very, very very welcome! Fly Fearlessly my friend 💪👍

@macelius 3 года назад

Awesome! Now if I could only get my 'battcheck' widget working in the top bar..

@TMacFPV 3 года назад

what "battcheck" do you mean? are you talking about your LiPo battery voltage reading? What transmitter do you have?

@macelius 3 года назад

@@TMacFPV Hey! I have the T16, the 'battcheck' widget is for the top bar. I have the VFAS (from frsky XSR) displayed in the value widget right next to it as well as voice alerts working fine, but battcheck (shows percentage, voltage, and little battery icon) might take more setup than just pointing to VFAS, possibly lua scripts from what i gathered(?), and i don't think i'm ready to dive in to that yet lol.

@TMacFPV 3 года назад

gotcha, understand. Have fun flyin'!👍

@toddbeal4373 4 года назад

#flightpath2fun. Good video. I was doing the x6b tonight and I was getting constant rssi lost and on again? Not sure why this is. But I am going to try and get that figured out. My flit14+ dont do that. Keep the videos going man. Thanks for the giveaway

@TMacFPV 4 года назад

Hey Todd! It's great to have various options like the R1😁

@mikeduncan2127 4 года назад

Are you planning on reviewing and setup for the Jumper R1F?

@TMacFPV 4 года назад

Hey Mike, great to hear from you! I don't have an R1F, so I'd have to get one. But it should be fairly simple to setup. Ground wire to ground pad, Power wire to 5 volt pad. FPort to SBUS pad on your flight controller. Toggle ON Serial RX in Ports Tab of Betaflight for the the UART associated with SBUS pad on your flight controller (see your Flight controller documentation for this as it varies by flight controller). In Configuration Tab select Serial RX and FPort under it. Toggle ON Telemetry in configuration Tab. Type the following commands into Betalfight CLI: set serialrx_halfduplex = OFF set serialrx_inverted = ON Hit Return on keyboard Type SAVE into CLI then hit return on keyboard FPort instructions from Betaflight page are here: github.com/betaflight/betaflight/wiki/The-FrSky-FPort-Protocol Grayson Hobby video for R1F is here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-cUEvQ4xcU7k.html

@mikeduncan2127 4 года назад

@@TMacFPV You must have watch the only RU-vid on setting up the R1F for a F4 from Grayson Hobbies which was wrong. Connecting to SBUS only provides rx functionality but no telemetry. I spent several hours on trying to get full telemetry. Below is how I get both rx and telemetry to work: Enable softserial Connect rx FPort to softserial tx (not SBUS as Grayson Hobby outlined) set serialrx_inverted = ON set serialrx_halfduplex = ON or OFF depending on firmware (BF or iNav) set telemetry_inverted = OFF set telemetry_halfduplex = ON (BF or iNav 2.3) set telemetry_uart_unidir = ON (iNav 2.4)

@TMacFPV 4 года назад

Hey Mike, great you got it working! Thanks for the info!👍I should've caught that Mike, my bad. Inverted telemetry signal going to F4! Been a long weekend for me!😉

@TMacFPV 4 года назад

Hey Mike, I've decided to do a video on the R1F (per your suggestion) as I'm getting a lot of questions on it. I've ordered one and am awaiting its arrival. Hopefully I can get video on it out this week. When researching stuff on it, I recalled you said you're doing it over Softserial. I've learned myself although it CAN be done this way, it's not recommended as your control signal is now also going over this Softserial. Softserial is software emulated and not meant for high data rate applications like control signals. You MAY not encounter issues, however, by doing it this way you're taking a chance on losing your control signal (and quad?). Just thought I'd pass the info on to you. I'd be interested in hearing from you as to whether or not you've flown with it yet and if so have you encountered any issues? Thanks! Also, what flight controller are you using?

@mikeduncan2127 4 года назад

@@TMacFPV Yes, I'm aware of the issues using a softserial UART for a rx channel. The issue with get full telemetry is only the F4 FC's. Though I did connected the R1F to a F3 with no problems. As far as for a F4, there are really only two solutions: 1) use a SBUS inverter or 2) wait for someone to figure out how to connect to an un-inverted pad on the R1F. I have a couple of SBUS inverter but decided just to shelf the R1F until an un-inverted hack is identified as on the FrSky X-series rx's. You are going to find out that binding with a T16 that you are going to have to change the freq offset be either 40 or -40. Though, binding to a FrSky Taranis is straight forward. My understanding is the current version of the T16 multi-protocol module firmware does not do freq optimization during the bind process like the FrSky radio does but they are apparently working the go firmware to incorporate these feature at some time. The only information on binding and configuring the R1F that I’ve come across has been on the Grayson Hobby website but neither of these issues are discussed. Good luck on the video. You will probably be the first to explain how to setup a R1F properly.

@mccolld11 4 года назад

Wanting to convert to Jumper! Dig your videos.....good info.

@TMacFPV 4 года назад

Thanks Ferociter! Welcome aboard!👍😁

@briansowder10 4 года назад

Sign me up id like to test one of these out #flightpath2fun Is a great resource thanks for the best tutorials on the jumper T16 on RU-vid to date Tmac.

@TMacFPV 4 года назад

You got it Brian! Thanks for your comment & good luck friend!😀